Explore the vast range of titles available.

In this work, we present an absorption cooling system with 35 kW capacity driven by solar thermal energy, installed in the school of Puertecitos, Mexico, an off-grid community with a high level of social marginalization. The cooling system provides thermal comfort to the school’s classrooms through four 8.75-kW cooling coils, while a 110-m2 field of evacuated tube solar collectors delivers the thermal energy needed to activate the cooling machine. The characteristics of the equipment installed in the school were used for simulation and operative analysis of the system under the influence of typical factors of an isolated coastal community, such as the influence of climate, thermal load, and water consumption in the cooling tower, among others. The aim of this simulation study was to determine the best operating conditions prior to system start-up, to establish the requirements for external heating and cooling services, and to quantify the freshwater requirements for the proper functioning of the system. The results show that, with the simulated strategies implemented, with a maximum load operation, the system can maintain thermal comfort in the classrooms for five days of classes. This is feasible as long as weekends are dedicated to raising the water temperature in the thermal storage tank. As the total capacity of the system is distributed in the four cooling coils, it is possible to control the cooling demand in order to extend the operation periods. Utilizing 75% or less of the cooling capacity, the system can operate continuously, taking advantage of stored energy. The cooling tower requires about 750 kg of water per day, which becomes critical given the scarcity of this resource in the community.

By the year 2020, 90% of the population with access to electricity worldwide was surpassed. However, the reality is very different for many countries, especially for those on the African continent that had more than 572 million people without electricity service at the end of 2019. This work studies the implementation of an isolated microgrid activated with photovoltaic energy and energy storage in batteries under the case study of the community of Bigene, located in the African country of Guinea-Bissau. This type of project is a potential solution to the problem of access to energy, but as the cost of the energy storage system is typically very high, this work technically and economically addresses the effect of using absorbed glass material (AGM) and lithium batteries. A simulator was developed using TRNSYS software to analyze the operation of the microgrid under a defined annual demand profile for different types of users, and economic analysis was conducted considering a project lifetime of 25 years. The results showed no significant differences in the solar fraction of both types of batteries when the photovoltaic power was less than 600 kW, regardless of the capacity of the storage bank. The analysis of auxiliary power requirements showed that lithium technology leads to a lower consumption from 800 kW of PV capacity, and utilizing less than this capacity did not have a significant difference with AGM batteries. In this microgrid with a photovoltaic capacity of less than 700 kW and an energy storage of less than 2580 kWh, the type of storage technology, AGM or lithium, did not represent a considerable difference in the levelized cost of energy, indicating that AGM technology could be selected considering its low initial investment cost compared to lithium batteries.

This paper is a summary of the last ten years of work on the study of parabolic trough collectors (PTCs) and compound parabolic collectors (CPCs) coupled to photovoltaic and thermal solar receiver collectors (SCR-PVTs). While reviewing the state of the art, numerous review papers were found that focused on conventional solar receiver collector (SRC) technology for solar thermal generation. However, there is a lack of review papers summarizing SRC-PVT hybrid technology for solar electric/thermal generation, which would be beneficial for researchers interested in this area of research. This paper provides a review of SRC-PVT hybrid technologies. The theoretical foundations for analyzing and modeling PTC and CPC concentrators coupled to SRC-PVT are described, with an emphasis on modeling through thermal resistances and energy balances. Additionally, this section provides a concise overview of previous studies that have addressed the modeling of PTC and CPC collectors coupled to SCR-PVT, as well as experimental information useful for the validation of new mathematical models of SRC-PVT.

This study presents a mathematical model of a parabolic trough solar collector with photovoltaic cells integrated into its solar receiver. A case study is presented, utilizing meteorological data obtained from the localities of Cuernavaca and Mexicali in Mexico. The results demonstrate moderately variable electrical and thermal energy production for Cuernavaca (387.93 kWh to 239.38 kWh and 1036.11 kWh to 641.26 kWh, respectively). In contrast, the production of electrical and thermal energy in Mexicali exhibited considerably greater fluctuations (515.16 kWh to 177.69 kWh and 1424.39 kWh to 448.88 kWh, respectively). Furthermore, a parametric study is presented, which analyzes the impact of solar receiver geometry and mass flow on the model’s behavior. The results demonstrate that the pipe length exerts the most significant influence on the electrical and thermal power output (1.21 kW to 2.22 kW and 3.7 kW to 6.9 kW, respectively). Additionally, the diameter has an impact on the thermal power output (5.23 kW to 7.1 kW) and the electrical and thermal efficiency (0.18 to 0.15 and 0.54 to 0.74, respectively). Modifying the mass flow facilitates the enhancement of electrical power and efficiency (1.54 kW to 1.72 kW and 0.16 to 0.18, respectively) while concurrently preventing a significant reduction in thermal power and efficiency (5.4 kW to 5.3 kW and 0.56 to 0.55, respectively). A script with the developed model is provided.

This work presents the results of indirectly coupling an Earth to Air Heat Exchanger to a 35 kW absorption cooling system. The study considers the weather, building, and soil conditions of a school located in the off-grid remote community of Puertecitos, Baja California, Mexico. TRNSYS simulation software was used to analyze the thermal behavior of the Earth to Air Heat Exchanger under different operation modes, in order to reduce the thermal load of the classrooms. The results show that during the months of May and June an Earth to Air Heat Exchanger with a diameter of 0.15 m, operating from Mondays to Fridays with and mass flow of 715 kg/h, is capable to reduce the thermal load of each classroom by 268.4 kWh t , equivalent to 25% of the energy to be removed for maintaining the classrooms at 25 °C, which is reflected in a reduction of 12.89% and 18.25% of the electrical energy and water consumption, respectively. For the period from August to October, the thermal load was reduced by 225.2 kWh t , equivalent to 15.4% of the energy to be removed for maintaining the classrooms temperature at 25 °C, causing an increase of 1.33% in electrical energy consumption, but reducing the consumption of auxiliary heat and water by 94.82% and 11.07%, respectively. The annual savings in auxiliary heat, electrical energy and water are 513.52 kWh t , 136.05 kWh e and 6,084.03 kg, which represent 94.82%, 4.61% and 14.3% of the annual consumption of these resources.

This work presents a novel trigeneration system for the simultaneous production of desalinated water, electrical energy, and cooling, addressing the challenges of water scarcity and climate change through an integrated and efficient approach. The proposed system combines an 8-stage Multi Stage Flash Distillation (MSF) process with a 6-effect Multiple Effect Distillation (MED) process, complemented by an expander-generator to optimize steam utilization. Cooling production is achieved through a dual ejectocondensation mechanism, which enhances energy recovery and expands operational flexibility. The system’s performance was analyzed using Aspen Plus simulations, demonstrating technical feasibility across a broad operating range: 28.3 to 0.8 kPa and 68 to 4 °C. In cogeneration mode, the system achieves a Performance Ratio (PR) of 12.06 and a Recovery Ratio (RR) of 54%, producing 67,219.2 L/day of desalinated water and reducing electrical consumption by 12.03%. In trigeneration mode, it achieves a PR of 17.81 and an RR of 80%, with a cooling capacity of 1225 kW, generating 99,273.6 L/day of desalinated water while reducing electrical consumption by 3.69%. These results underscore the system’s capability to significantly enhance the efficiency and capacity of thermal desalination technologies, offering a sustainable and high-performing solution for coastal communities worldwide.

Solar energy is one of the main alternatives for the decarbonization of the electricity sector and the reduction of the existing energy deficit in some regions of the world. However, one of its main limitations lies in its storage, since this energy source is intermittent. This paper evaluates the potential of an underground thermal energy storage tank supplied by solar thermal collectors to provide hot water for the activation of a single-effect absorption cooling system. A simulator was developed in TRNSYS 17 software. Experimentally on-site measured data of soil temperature were used in order to increase the accuracy of the simulation. The results show that the underground tank reduces thermal energy losses by 27.6% during the entire hot period compared with the air-exposed tank. The electrical energy savings due to the reduction in pumping time during the entire hot period was 639 kWh, which represents 23.6% of the electrical energy consumption of the solar collector pump. It can be concluded that using an underground thermal energy storage tank is a feasible option in areas with high levels of solar radiation, especially in areas where ambient temperature drops significantly during night hours and/or when access to electrical energy is limited.

This research paper presents a review of the state of the art of desalination in Mexico, with the aim of clarifying the main challenges and opportunity areas for desalination as the main solution to overcome water stress. First, the current situation and forecasts on the availability of water resources in Mexico are described, followed by the main economic, social, and legislative issues of desalination. Mexico’s installed capacity for the different desalination technologies and their evolution in recent years was investigated, followed by a comparison with global trends. The current state of research and development in desalination technologies carried out by Mexican institutions was also studied. The results show that membrane technology plants account for 88.85%, while thermal technology plants account for the remaining 11.15%. Although Mexico presented a 240% increase in its desalination capacity in the last 10 years, it has not been enough to overcome water stress, so it is concluded that in the future, it is necessary to increase its capacity in greater proportion, specifically in the areas with greater scarcity, which can be achieved with the joint participation of academy–industry–government through the creation of autonomous organizations, social programs, and/or public policies that promote it.

Water is a necessary resource for life development. Its excessive consumption has a negative impact, generating scarcity problems worldwide. Desalination is an alternative to solve these problems; its objective is to reduce the concentration of total dissolved solids to levels suitable for consumption. The most widely used desalination technology is reverse osmosis, which works by means of semipermeable membranes; however, lack of knowledge or wrong operation cause phenomena such as concentration polarization, which reduces the effective area for mass transfer in the membrane, increasing the energy consumption of the process. The objective of the present study is to evaluate the concentration polarization (β) of the concentration in reverse osmosis membranes by varying the temperature in the feed water (23, 25.5, 28, and 35 °C) for different concentrations (5000 and 10,000 mg L−1) in order to reduce its impact on energy consumption (kWh m−3). The results show that as the temperature increases, the specific energy consumption decreases for both concentrations. In the 5000 mg L−1 tests, the specific energy consumption decreased by 0.590 kWh m−3, representing 12.5%. For 10,000 mg L−1 tests, the specific energy consumption shows a reduction of 0.72 kWh m−3, which represents a percentage decrease of 14.54%.

In this work, the analysis of a hybrid LiBr/H2O absorption-cooling and flash-desalination system, using solar thermal energy as heat source, is presented. An absorption open-cycle with three pressure levels is used in combination with a single-stage flash-desalination process to use the coolant as product water, resulting in an increase in cooling and desalination efficiency. For the application, a 20-room coastal hotel complex in San Felipe, Baja California, Mexico, is taken as a case study and the sizing of the solar collection and storage system is carried out for the operation of the proposed hybrid system, during the summer operative period. The operational dynamics during the week with the highest ambient temperatures are presented. The dimensioning of the solar collector’s area and the energy storage resulted in a collection area of 620 m2 with 30 m3, respectively, reaching a solar fraction of 69%. The absorption-cooling subprocess showed an increase of 13.88% in the average coefficient of performance (COP) compared to conventional LiBr/H2O absorption systems. Also, considering that the system provides cooling and desalination simultaneously, the average COPG is 1.64, which is 2.27 times higher than the COP of conventional LiBr/H2O single-effect absorption units. During the critical week, the system presented a desalinated water production of 16.94 m3 with an average performance ratio (PR) of 0.83, while the average daily water production was 2406 kg/day; enough to satisfy the daily water requirements of four people in a coastal hotel in Mexico or to cover the basic services of 24 people according to the World Health Organization.