Explore the vast range of titles available.

Given the good performances in terms of geometrical acceptance and energy resolution, calorimeters are the best suited detectors to measure high energy cosmic rays directly in space. However, in order to exploit this potential, the design of calorimeters must be carefully optimized to take into account all limitations related to space missions, due mainly to the mass of the experimental apparatus. CaloCube is a three years R&D project, approved and financed by INFN in 2014, aiming to optimize the design of a space-borne calorimeter by the use of a cubic, homogeneous and isotropic geometry. In order to maximize detector performances with respect to the total mass of the apparatus, comparative studies on different scintillating materials, different sizes of crystals and different spacings among them have been performed making use of Monte Carlo simulations. In parallel to this activity, several prototypes instrumented with CsI:Tl cubic crystals have been constructed and tested with particle beams (muons, electrons, protons and ions). Both simulations and prototypes showed that the CaloCube design leads to a good particle energy resolution (< 2% for electromagnetic showers, < 40% for hadronic showers) and a good effective geometric factor (> 3:5 m2 sr for electromagnetic showers, > 2:5 m2 sr for hadronic showers). Thanks to these performances, in 5 years of operation it would be possible to measure the ux of electrons+positrons up to some tens of TeV and the uxes of protons and nuclei up to some units of PeV/nucleon, hence extending these measurements by at least one order of magnitude in energy compared to the experiments currently operating in space.

The direct measurement of the cosmic-ray spectrum, up to the knee region, is one of the instrumental challenges for next generation space experiments. The main issue for these measurements is a steeply falling spectrum with increasing energy, so the physics performance of the space calorimeters are primarily determined by their geometrical acceptance and energy resolution. CaloCube is a three-year R&D project, approved and financed by INFN in 2014, aiming to optimize the design of a space-born calorimeter. The peculiarity of the design of CaloCube is its capability of detecting particles coming from any direction, and not only those on its upper surface. To ensure that the quality of the measurement does not depend on the arrival direction of the particles, the calorimeter will be designed as homogeneous and isotropic as possible. In addition, to achieve a high discrimination power for hadrons and nuclei with respect to electrons, the sensitive elements of the calorimeter need to have a fine 3-D sampling capability. In order to optimize the detector performances with respect to the total mass of the apparatus, which is the most important constraint for a space launch, a comparative study of different scintillating materials has been performed using detailed Monte Carlo simulation based on the FLUKA package. In parallel to simulation studies, a prototype consisting in 14 layers of 3 x 3 CsI(Tl) crystals per layer has been assembled and tested with particle beams. An overview of the obtained results during the first two years of the project will be presented and the future of the detector will be discussed too.

Future space experiments dedicated to the observation of high-energy gamma and cosmic rays will increasingly rely on a highly performing calorimetry apparatus, and their physics performance will be primarily determined by the geometrical dimensions and the energy resolution of the calorimeter deployed. Thus it is extremely important to optimize its geometrical acceptance, the granularity, and its absorption depth for the measurement of the particle energy with respect to the total mass of the apparatus which is the most important constraint for a space launch. The proposed design tries to satisfy these criteria while staying within a total mass budget of about 1.6 tons. Calocube is a homogeneous calorimeter instrumented with Cesium iodide (CsI) crystals, whose geometry is cubic and isotropic, so as to detect particles arriving from every direction in space, thus maximizing the acceptance; granularity is obtained by filling the cubic volume with small cubic CsI crystals. The total radiation length in any direction is more than adequate for optimal electromagnetic particle identification and energy measurement, whilst the interaction length is at least suficient to allow a precise reconstruction of hadronic showers. Optimal values for the size of the crystals and spacing among them have been studied. The design forms the basis of a three-year R&D activity which has been approved and financed by INFN. An overall description of the system, as well as results from preliminary tests on particle beams will be described.

The 11-yr variation of galactic cosmic-ray flux lags behind the variation of the sunspot number. An average ~1-yr time-lag is expected from the outward propagating solar wind with the frozen-in photospheric magnetic field varying in the solar cycle, and from the inward diffusive transport of cosmic-ray particles. The long-term neutron monitor data, however, show that the time-lag is significantly longer (shorter) in the odd (even) solar cycle. In this paper, we analyze the time-lag in proton and electron fluxes observed by the CALET. It is found that the time-lag is similar in proton and electron fluxes during an A > 0 polarity epoch of the solar dipole magnetic field. In an even solar cycle 24 including a polarity reversal from A < 0 to A > 0, on the other hand, it is found that the time-lag of proton (electron) flux variation is significantly shorter (longer) than the average ~1-yr lag by analyzing the combined data with CALET and AMS-02. This is the first observation of the charge-sign dependent time-lag. We demonstrate that these observations can be qualitatively interpreted in terms of different 11-yr time profiles of proton and electron fluxes in A > 0 and A < 0 epochs expected from the drift effect.

Abstract The 11-yr variation of galactic cosmic-ray flux lags behind the variation of the sunspot number. An average $\\sim$1-yr time-lag is expected from the outward propagating solar wind with the frozen-in photospheric magnetic field varying in the solar cycle, and from the inward diffusive transport of cosmic-ray particles. The long-term neutron monitor data, however, show that the time-lag is significantly longer (shorter) in the odd (even) solar cycle. In this paper, we analyze the time-lag in proton and electron fluxes observed by the Calorimetric Electron Telescope (CALET). It is found that the time-lag is similar in proton and electron fluxes during an $A > 0$ polarity epoch of the solar dipole magnetic field. In an even solar cycle 24 including a polarity reversal from $A < 0$ to $A > 0$, on the other hand, it is found that the time-lag of proton (electron) flux variation is significantly shorter (longer) than the average $\\sim$1-yr lag by analyzing the combined data with CALET and AMS-02. This is the first observation of the charge-sign dependent time-lag. We demonstrate that these observations can be qualitatively interpreted in terms of different 11-yr time profiles of proton and electron fluxes in $A > 0$ and $A < 0$ epochs expected from the drift effect.

Current research in High Energy Cosmic Ray Physics touches on fundamental questions regarding the origin of cosmic rays, their composition, the acceleration mechanisms, and their production. Unambiguous measurements of the energy spectra and of the composition of cosmic rays at the \"knee\" region could provide some of the answers to the above questions. So far only ground based observations, which rely on sophisticated models describing high energy interactions in the earth's atmosphere, have been possible due to the extremely low particle rates at these energies. A calorimetry based space experiment that could provide not only flux measurements but also energy spectra and particle identification, would certainly overcome some of the uncertainties of ground based experiments. Given the expected particle fluxes, a very large acceptance is needed to collect a sufficient quantity of data, in a time compatible with the duration of a space mission. This in turn, contrasts with the lightness and compactness requirements for space based experiments. We present a novel idea in calorimetry which addresses these issues whilst limiting the mass and volume of the detector. In this paper we report on a four year R&D program where we investigated materials, coatings, photo-sensors, Front End electronics, and mechanical structures with the aim of designing a high performance, high granularity calorimeter with the largest possible acceptance. Details are given of the design choices, component characterisation, and of the construction of a sizeable prototype (Calocube) which has been used in various tests with particle beams.

CaloCube is an R&D project borne to develop a novel calorimeter design, optimized for high-energy cosmic ray measurements in space. A small prototype made of CsI(Tl) elements has been built and tested on particle beams. A final version, made of 5×5×18 crystals and with dual readout (two photodiodes for each crystal), to cover the full required dynamic range, is under construction and will be tested at CERN SPS in Summer 2016. The dual readout compensation technique were developed and the feasibility to extract Čerenkov signals from CsI crystals verified.

The multi-TeV energy region of the cosmic-ray spectra has been recently explored by direct detection experiments that used calorimetric techniques to measure the energy of the cosmic particles. Interesting spectral features have been observed in both all-electron and nuclei spectra. However, the interpretation of the results is compromised by the disagreements between the data obtained from the various experiments, that are not reconcilable with the quoted experimental uncertainties. Understanding the reason for the discrepancy among the measurements is of fundamental importance in view of the forthcoming high-energy cosmic-ray experiments planned for space, as well as for the correct interpretation of the available results. The purpose of this work is to investigate the possibility that a systematic effect may derive from the non-proportionality of the light response of inorganic crystals, typically used in high-energy calorimetry due to their excellent energy-resolution performance. The main reason for the non-proportionality of the crystals is that scintillation light yield depends on ionisation density. Experimental data obtained with ion beams were used to characterize the light response of various scintillator materials. The obtained luminous efficiencies were used as input of a Monte Carlo simulation to perform a comparative study of the effect of the light-yield non-proportionality on the detection of high-energy electromagnetic and hadronic showers. The result of this study indicates that, if the calorimeter response is calibrated by using the energy deposit of minimum ionizing particles, the measured shower energy might be affected by a significant systematic shift, at the level of few percent, whose sign and magnitude depend specifically on the type of scintillator material used.

Detailed measurements of the spectral structure of cosmic-ray electrons and positrons from 10.6 GeV to 7.5 TeV are presented from over 7 years of observations with the CALorimetric Electron Telescope (CALET) on the International Space Station. Because of the excellent energy resolution (a few percent above 10 GeV) and the outstanding e/p separation (10\\(^5\\)), CALET provides optimal performance for a detailed search of structures in the energy spectrum. The analysis uses data up to the end of 2022, and the statistics of observed electron candidates has increased more than 3 times since the last publication in 2018. By adopting an updated boosted decision tree analysis, a sufficient proton rejection power up to 7.5 TeV is achieved, with a residual proton contamination less than 10%. The observed energy spectrum becomes gradually harder in the lower energy region from around 30 GeV, consistently with AMS-02, but from 300 to 600 GeV it is considerably softer than the spectra measured by DAMPE and Fermi-LAT. At high energies, the spectrum presents a sharp break around 1 TeV, with a spectral index change from -3.15 to -3.91, and a broken power law fitting the data in the energy range from 30 GeV to 4.8 TeV better than a single power law with 6.9 sigma significance, which is compatible with the DAMPE results. The break is consistent with the expected effects of radiation loss during the propagation from distant sources (except the highest energy bin). We have fitted the spectrum with a model consistent with the positron flux measured by AMS-02 below 1 TeV and interpreted the electron + positron spectrum with possible contributions from pulsars and nearby sources. Above 4.8 TeV, a possible contribution from known nearby supernova remnants, including Vela, is addressed by an event-by-event analysis providing a higher proton-rejection power than a purely statistical analysis.

The measurement of cosmic-ray individual spectra provides unique information regarding the origin and propagation of astro-particles. Due to the limited acceptance of current space experiments, protons and nuclei around the \"knee\" region (\\(\\sim1\\ PeV\\)) can only be observed by ground based experiments. Thanks to an innovative design, the High Energy cosmic-Radiation Detection (HERD) facility will allow direct observation up to this energy region: the instrument is mainly based on a 3D segmented, isotropic and homogeneous calorimeter which properly measures the energy of particles coming from each direction and it will be made of about 7500 LYSO cubic crystals. The read-out of the scintillation light is done with two independent systems: the first one based on wave-length shifting fibers coupled to Intensified scientific CMOS cameras, the second one is made of two photo-diodes with different active areas connected to a custom front-end electronics. This photo-diode system is designed to achieve a huge dynamic range, larger than \\(10^7\\), while having a small power consumption, few mW per channel. Thanks to a good signal-to-noise ratio, the capability of a proper calibration, by using signals of both non-interacting and showering particles, is also guaranteed. In this paper, the current design and the performance obtained by several tests of the photo-diode read-out system are discussed.