Explore the vast range of titles available.

This research presents a dual-pronged bibliometric and systematic review of the integration of phase change materials (PCM) in asphalt pavements to counteract the urban heat island (UHI) effect. The bibliometric approach discerns the evolution of PCM-inclusion asphalt research, highlighting a marked rise in the number of publications between 2019 and 2022. Notably, Chang’an University in China has emerged as a leading contributor. The systematic review addresses key questions like optimal PCM types for UHI effect mitigation, strategies for PCM leakage prevention in asphalt, and effects on mechanical properties. The findings identify polyethylene glycols (PEGs), especially PEG2000 and PEG4000, as prevailing PCM due to their wide phase-change temperature range and significant enthalpy during phase transitions. While including PCM can modify asphalt’s mechanical attributes, such mixtures typically stay within performance norms. This review emphasises the potential of PCM in urban heat management and the need for further research to achieve optimal thermal and mechanical balance.

This work describes the development of a capacitive-type sensor created from nanoporous anodic aluminium oxide (NP-AAO) prepared by the one-step anodization method conducted in potentiostatic mode and performed in a low-cost homemade system. A series of samples were prepared via an anodization campaign carried out on different acid electrolytes, in which the anodization parameters were adjusted to investigate the effect of pore size and porosity on the capacitive sensing performance. Two sensor test cases are investigated. The first case explores the use of highly uniform NP-AAO structures for humidity sensing applications while the second analyses the use of NP-AAO as a capacitive touch sensor for biological applications, namely, to detect the presence of small “objects” such as bacterial colonies of Escherichia Coli. A mathematical model based on equivalent electrical circuits was developed to evaluate the effect of humidity condensation (inside the pores) on the sensor capacitance and also to estimate the capacitance change of the sensor due to pore blocking by the presence of a certain number of bacterial microorganisms. Regarding the humidity sensing test cases, it was found that the sensitivity of the sensor fabricated in a phosphoric acid solution reaches up to 39 (pF/RH%), which is almost three times higher than the sensor fabricated in oxalic acid and about eight times higher than the sensor fabricated in sulfuric acid. Its improved sensitivity is explained in terms of the pore size effect on the mean free path and the loss of Brownian energy of the water vapour molecules. Concerning the touch sensing test case, it is demonstrated that the NP-AAO structures can be used as capacitive touch sensors because the magnitude of the capacitance change directly depends on the number of bacteria that cover the nanopores; the fraction of the electrode area activated by bacterial pore blocking is about 4.4% and 30.2% for B1 (E. Coli OD600nm = 0.1) and B2 (E. Coli OD600nm = 1) sensors, respectively.

Second-generation thin-film Cu(In, Ga)Se2 (CIGS) solar cells are a well-established photovoltaic technology with a record power conversion efficiency of 23.6%. However, their reliance on critical raw materials, such as In and Ga, requires new approaches to reduce the amount of critical raw materials employed. The micro-concentrator concept involves the combination of thin-film photovoltaic technology with concentrator photovoltaic technology. This approach reduces the size of the solar cell to the micrometer range and uses optical concentration to collect sunlight from a larger area, focusing it onto micro solar cells. This work is devoted to the development of a process for manufacturing pre-structured substrates with regular arrays of holes with 200 and 250 µm diameters inside a SiOx insulating matrix. Subsequently, a Cu–In–Ga precursor is deposited by sputtering, followed by photoresist lift-off and the application of a Cu–In–Ga thermal annealing at 500 °C to improve precursor quality and assess pre-structured substrate stability under elevated temperatures. Finally, a two-stage selenization process leads to the formation of CIGS absorber micro-dots. This study presents in detail the fabrication process and explores the feasibility of a bottom-up approach using pre-structured substrates, addressing challenges encountered during fabrication and providing insights for future improvements in CIGS absorber materials.

Micro-concentrator photovoltaics combine sub-millimeter scale solar cells with optical concentrator systems, enabling higher power conversion efficiencies, material savings, and improved heat management. In this work, we investigated the effects of thermal treatment of Cu–In–Ga precursors on Cu(In,Ga)Se2 micro solar cells. The devices were fabricated by sputtering a Cu–In–Ga precursor onto a soda-lime glass/SiOxNy/Mo/SiOx pre-structured substrate with micro-holes of 200 and 250 µm diameter, defined by photolithography. The precursor undergoes thermal treatment at 450 °C, followed by selenization at 480 °C. The treated Cu–In–Ga exhibited a smoother surface, with indistinct grains, compared to the as-deposited film. However, areas of exposed Mo were observed upon treatment. After selenization, the treated micro-absorber exhibited improved elemental composition with Cu to (Ga + In) ratio of 0.81 ± 0.06, compared to 0.76 ± 0.13 for the untreated micro-absorber. Electrical characterization of the devices revealed better overall performance for the treated Cu(In,Ga)Se2 micro solar cells, with an average Voc of (239 ± 26) mV, significantly higher than the (176 ± 25) mV achieved by untreated micro cells.

Nowadays, the growing concern about improving thermal comfort in different structures (textiles, buildings, and pavements, among others) has stimulated research into phase change materials (PCMs). The direct incorporation of PCMs into composite materials can cause mechanical impacts. Therefore, this study focuses on the design of phase change coaxial fibres (PCFs), using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as the sheath and polyethylene glycol (PEG) 2000 as the core, via the wet spinning method; the fibres vary in molecular weight, concentration and ejection velocity. The fibres were assessed for their optical, chemical, thermal, and mechanical properties. The presence of PEG2000 is confirmed in the core of the fibres. Thermal analyses revealed a mass loss at high temperatures, attributable to the presence of PEG2000. Notably, the fibres with CA (Mn 30,000) showed superior thermal and mechanical performance. The melting point of PEG2000 incorporated into these PCFs coincided with the melting point of pure PEG2000 (about 55 °C), with a slight deviation, indicating that PCFs were obtained. Finally, the results point to the application of the fibres in civil engineering materials requiring a phase change between 50 and 60 °C, providing promising prospects for their use in applications requiring thermoregulatory properties.

Road markings (RMs) typically consist of a paint layer and a retroreflective layer. They play a crucial role in road safety by offering visibility and guidance to drivers. Over their lifetime, dirt particles, oils, and greases are adsorbed on the RM surface, reducing their visibility and service life. A self-cleaning ability has been widely studied in several substrates. However, for RMs, this represents a breakthrough and a sustainable advance, while having the potential to increase their service life and enhance road safety. In this context, nanotechnology can be a strong ally through the application of semiconductor materials, such as TiO2, to develop the self-cleaning ability. In addition to this novelty in RMs, quantifying this ability in terms of pollutant removal efficiency is also a challenge. In this sense, artificial intelligence (AI) and colorimetry can be combined to achieve improved results. The aims of the work herein reported were to assess the self-cleaning capability in an RM paint through the mass incorporation of semiconductors, evaluate their photocatalytic efficiency using traditional (spectrophotometric) and modern (AI-enhanced) colorimetry techniques, and compare the results obtained using both techniques. To this end, a water-based acrylic RM paint was modified through the mass incorporation of 0.5%, 1%, 2%, and 3% of nano-TiO2, and a pollutant model widely used, Rhodamine B, was applied onto their surface. The samples were irradiated with a light source that simulates sunlight for 0, 3, 6, 12, 24, and 48 h. Visual analysis and spectrophotometric and artificial intelligence-enhanced colorimetry techniques were used and compared to evaluate the pollutant removal. The results confirm that RM paints with 2% and 3% nano-TiO2 incorporated have a significantly higher pollutant removal ability and that both colorimetric techniques used are suitable for this assessment.

Rapid urbanisation and industrialisation have intensified the Urban Heat Island (UHI) effect, significantly increasing energy demand for thermal comfort. Urban buildings consume considerable energy throughout the year, which can be reduced by incorporating Phase Change Materials (PCMs) into building materials. PCMs effectively regulate temperature by storing and releasing heat as latent heat during phase transitions. However, to prevent leakage, PCMs can be encapsulated in co-axial polymeric Phase Change Fibres (PCFs), representing an innovative approach in scientific research. This study optimised the coagulation bath and produced PCFs using commercial cellulose acetate as the sheath and polyethylene glycol (PEG 600 and 1000) as the core via the wet-spinning method. The first part of this work investigated the coagulation bath using Attenuated Total Reflectance-Fourier Transform Infrared Spectroscopy (ATR-FTIR) analyses of the characteristic peak areas. In contrast, the second part examined the PCFs’ morphological, chemical and thermal properties using Bright-field microscopy, ATR-FTIR, Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA) techniques. The results demonstrated the successful production of PCFs with an optimised coagulation bath. Bright-field microscopy and ATR-FTIR confirmed the well-defined morphology and the presence of PEG in the fibre core. TGA analysis showed high thermal stability in the PCFs, with mass loss observed at high degradation temperatures, ranging from ~264 °C to 397 °C for the PCFs with PEG 600 and from ~273 °C to 413 °C for the PCFs with PEG 1000. Meanwhile, DSC analysis revealed melting points of ~12.64 °C and 11.04 °C, with endothermic enthalpy of ~39.24 °C and 30.59 °C and exothermic enthalpy of ~50.17 °C and 40.93 °C, respectively, for PCFs with PEG 600, and melting points of ~40.32 °C and 41.13 °C, with endothermic enthalpy of ~83.47 °C and 98.88 °C and exothermic enthalpy of ~84.66 °C and 88.79 °C, respectively, for PCFs with PEG 1000. These results validate the potential of PCFs for applications in building materials for civil engineering, promoting thermal efficiency and structural stability.

A smart asphalt mixture holds new capabilities different from the original ones or can react to a stimulus. These capabilities can be categorized based on smartness or function: smartness, mechanical, electrical, optical, energy harvesting, electromagnetic wave/radiation shielding/absorbing, and water related. The most important capabilities applied to asphalt mixtures are the photocatalytic, self-cleaning, self-healing, superhydrophobic, thermochromic, deicing/anti-icing, and latent heat thermal energy storage abilities. This research deals with a bibliometric review of the peer-reviewed journal articles published on the Scopus database, with the strings of terms related to these capabilities and asphalt or bitum in their titles, abstracts, and keywords. The review analysis highlighted the increasing number of accumulated publications, confirming the relevance of this research topic in recent years. The capability most often referred to was self-healing. The study showed that China was the most productive country. Research articles were mostly published in the journal Construction and Building Materials. Several techniques and methods are being developed regarding smart asphalt mixtures; for that reason, this research work aims to evaluate the literature under a bibliometric analysis.

Transparent binder is used to substitute conventional black asphalt binder and to provide light-colored pavements, whereas nano-TiO2 has the potential to promote photocatalytic and self-cleaning properties. Together, these materials provide multifunction effects and benefits when the pavement is submitted to high solar irradiation. This paper analyzes the physicochemical and rheological properties of a transparent binder modified with 0.5%, 3.0%, 6.0%, and 10.0% nano-TiO2 and compares it to the transparent base binder and conventional and polymer modified binders (PMB) without nano-TiO2. Their penetration, softening point, dynamic viscosity, master curve, black diagram, Linear Amplitude Sweep (LAS), Multiple Stress Creep Recovery (MSCR), and Fourier Transform Infrared Spectroscopy (FTIR) were obtained. The transparent binders (base and modified) seem to be workable considering their viscosity, and exhibited values between the conventional binder and PMB with respect to rutting resistance, penetration, and softening point. They showed similar behavior to the PMB, demonstrating signs of polymer modification. The addition of TiO2 seemed to reduce fatigue life, except for the 0.5% content. Nevertheless, its addition in high contents increased the rutting resistance. The TiO2 modification seems to have little effect on the chemical functional indices. The best percentage of TiO2 was 0.5%, with respect to fatigue, and 10.0% with respect to permanent deformation.Transparent binder is used to substitute conventional black asphalt binder and to provide light-colored pavements, whereas nano-TiO2 has the potential to promote photocatalytic and self-cleaning properties. Together, these materials provide multifunction effects and benefits when the pavement is submitted to high solar irradiation. This paper analyzes the physicochemical and rheological properties of a transparent binder modified with 0.5%, 3.0%, 6.0%, and 10.0% nano-TiO2 and compares it to the transparent base binder and conventional and polymer modified binders (PMB) without nano-TiO2. Their penetration, softening point, dynamic viscosity, master curve, black diagram, Linear Amplitude Sweep (LAS), Multiple Stress Creep Recovery (MSCR), and Fourier Transform Infrared Spectroscopy (FTIR) were obtained. The transparent binders (base and modified) seem to be workable considering their viscosity, and exhibited values between the conventional binder and PMB with respect to rutting resistance, penetration, and softening point. They showed similar behavior to the PMB, demonstrating signs of polymer modification. The addition of TiO2 seemed to reduce fatigue life, except for the 0.5% content. Nevertheless, its addition in high contents increased the rutting resistance. The TiO2 modification seems to have little effect on the chemical functional indices. The best percentage of TiO2 was 0.5%, with respect to fatigue, and 10.0% with respect to permanent deformation.

This study investigates the effect of iron-modified nano-TiO2, using the co-precipitation method with different concentrations of FeCl3 (0.1, 1, and 10%), to improve its photocatalytic properties for outdoor applications. To this end, modified and unmodified nano-TiO2 were characterized using different techniques. The optical properties were characterized by diffuse reflectance spectroscopy (DRS) followed by band gap calculation. X-ray diffraction (XRD) was used to analyze the crystalline structure. Chemical and morphological characterization were carried out using energy-dispersive X-ray spectroscopy (EDS) and scanning electron microscopy (SEM). The photocatalytic activity was investigated by decolorizing Rhodamine B aqueous solutions under similar sunlight irradiation. The results indicate that the modification improved light absorption in the UV range for all iron concentrations; however, only the concentration of TiO2: FeCl3 (10%) shifted the absorption to the visible region. Also, including Fe3⁺ in TiO2 decreased the band gap energy from 3.14 to up to 2.80 eV. There were variations in crystallite size from 21.13 to up to 40.07 nm. The nano-TiO2 morphology analysis showed that it did not change after iron modification. EDS showed an FeCl3 peak only at higher concentrations (10%). In addition, the 0.1% Fe-modified TiO2 exhibited the highest activity in the photocatalytic process, with an efficiency of 95.23% after 3 h of irradiation.