Explore the vast range of titles available.

Different amounts of a stable aqueous TiO2 hydrosol were used to fabricate paper sheets having photocatalytic activity. The TiO2 hydrosol was prepared in aqueous medium using titanium butoxide as precursor and acetic acid as catalyst for the hydrolysis of titanium butoxide. An aging process at room temperature and atmospheric pressure was finally applied to obtain crystalline anatase TiO2 hydrosol. The effects of different TiO2 hydrosol loadings on the mechanical strength and barrier properties of modified paper sheets were investigated in detail. The photocatalytic behavior of TiO2-modified paper sheets was investigated as well using methylene blue (MB) as target pollutant.

Polyurethane (PU) is widely recognized for its efficient oil sorption properties. However, this capacity is highly dependent on its intrinsic chemical composition and morphological structure, which can be altered by mechanical or chemical treatments commonly applied before using it as a sorbent. In this study, we present a comprehensive investigation of the oil sorption behavior of both soft and rigid PU foams, and their blade-milled ground (BMG) counterparts obtained by mechanical treatment of several recycled PU-based products, including seats, mattresses, side panels of cars, packaging components, and insulating panels of refrigerators and freezers. We found that blade milling the soft PU foams leads to a significant reduction in oil sorption capacity proportional to the extent of grinding. Pristine soft PU foams and BMG-PUs with intermediate particle size (−250 μm–1 mm) exhibited the highest oil uptake (20–30 g/g), whereas the finest fraction (5 μm–250 μm) showed a lower capacity (3–7 g/g). In contrast, rigid PU foams showed consistently low oil sorption (~5 g/g), with negligible differences between the original and ground materials. At the macroscopic level, optical and morphological analyses revealed the collapse of the 3D porous network and a reduction in surface area. On the microscopic scale, spectroscopic, structural, and thermal analyses confirmed phase separation and rearrangement of hard and soft segmented domains within the polymer matrix, suggesting a different mechanism for oil sorption in BMG-PU. Despite reduced performance compared to pristine foams, BMG-PU powders, especially those with intermediate dimensions and originating from soft PU foams, present a viable, low-cost, and sustainable alternative for oil sorption applications, including oil spill remediation, while offering an effective strategy for effective recycling of PU foam wastes.

Herein we present facile and green two-steps method for the fabrication of silver-carboxylated nanocellulose (Ag-ONCs) nanocomposite. Respecting the Circular Economy principle, the ONCs are prepared starting from the treatment of agriculture bagasse waste with ammonium persulfate—APS. This method permits to obtain ONCs fibers with rod or whisker shapes, with size and length in the range 6–10 nm and 90–150 nm, respectively. Ag-ONCs are then fabricated using a green photochemical approach. The UV irradiation works as radical initiator for the silver reduction, in water solution and at room temperature. The ONCs act as a template and reducing agent for silver nanoparticles formation, due to the specific hydroxyl and carboxyl groups on the cellulose surface. The structural and morphological properties of ONCs and Ag-ONCs nanocomposite are well evaluated by FT-IR, XRD, UV–Vis, AFM, SEM and TEM characterizations. The results showed that well crystalline, quasi-spherical silver nanoparticles of about 4–10 nm dispersed in the ONCs matrix are fabricated. Qualitative antibacterial tests towards gram negative (Escherichia coli and Pseudomonas aeruginosa) and gram positive (Staphylococcus aureus and Bacillus subtilis) bacteria are carried out and the results demonstrated that the Ag-ONCs inhibit the bacteria growth, with 12–14 mm of inhibition zone for both the bacteria groups. Also, quantitative antibacterial tests for E. coli, chosen as representative for its diffusion, are carried out and the bacteria growth rate and the inhibition rate for Ag-ONCs at different concentrations are evaluated. The analysis showed that the MIC (minimum inhibition concentration) for Ag is about 110 µg/mL for E. coli. These results demonstrated that the Ag-ONCs possess suitable and promising antibacterial behavior and could be used for industrial and technological application.

Digital and green energy transitions are driving an unprecedented demand for Strategic and Critical Raw Materials (S-CRMs), necessitating the identification of alternative sources such as secondary raw materials from exploration and mining residues. This study investigates an integrated, multi-scale approach to map and recover S-CRMs from an abandoned exploration stockpile in Zlatá Baňa, Slovak Republic. A key aspect of the methodology is comprehensive chemical and mineralogical characterization (XRF, PXRD, FTIR, LIBS, and SEM-EDS), which provided scientific validation for the diagnostic absorption features observed in laboratory reflectance spectra. These laboratory-acquired signatures were then used as endmembers to classify Sentinel-2 imagery via the Spectral Angle Mapper (SAM) algorithm. This integration enabled the identification of three distinct residue classes, with classA (jarosite-rich residues) emerging as the most reactive facies. Subsequent bioleaching experiments using Acidithiobacillus ferrooxidans demonstrated that microbial activity more than doubled Zn mobilization compared to abiotic controls. This cross-disciplinary strategy confirms that the synergy between advanced analytical characterization and remote sensing provides a robust, cost-effective pathway for the sustainable recovery of S-CRMs in regions affected by historical and mining activities.

A simple, environmentally benign and energy efficient process for fabricating single faced superhydrophilic/hydrophobic cotton fabrics by controlling surface texture and chemistry at the nano/microscale is reported here. Stable ultra-hydrophobic surfaces with advancing and receding water droplet contact angles in excess of 146° as well as extreme superhydrophilic surfaces are obtained. Hydrophobic water-repellent cotton fabrics were obtained following plasma treatment through diamond-like carbon (DLC) coating by plasma enhanced chemical vapour deposition. The influence of changing different precursor’s plasma pre-treatments such as H₂, Ar or O₂ on the properties of DLC coatings is also evaluated using atomic force microscopy, X-ray photoelectron spectroscopy, attenuated total reflection Fourier transform infrared spectroscopy, and analysed in terms of contact angle measurements. Because of the DLC coating, the coated fabric showed to endure its superhydrophobic character even after 12 months.

The impact of extra-low dosage (0.01% by weight of cement) Graphene Oxide (GO) on the properties of fresh and hardened nanocomposites was assessed. The use of a minimum amount of 2-D nanofiller would minimize costs and sustainability issues, therefore encouraging the market uptake of nanoengineered cement-based materials. GO was characterized by X-ray Photoelectron Spectroscopy (XPS), Fourier-transform infrared spectroscopy (FTIR), Atomic Force Microscopy (AFM), X-ray Diffraction (XRD), and Raman spectroscopy. GO consisted of stacked sheets up to 600 nm × 800 nm wide and 2 nm thick, oxygen content 31 at%. The impact of GO on the fresh admixtures was evaluated by rheology, flowability, and workability measurements. GO-modified samples were characterized by density measurements, Scanning Electron Microscopy (SEM) analysis, and compression and bending tests. Permeability was investigated using the boiling-water saturation technique, salt ponding test, and Initial Surface Absorption Test (ISAT). At 28 days, GO-nanocomposite exhibited increased density (+14%), improved compressive and flexural strength (+29% and +13%, respectively), and decreased permeability compared to the control sample. The strengthening effect dominated over the adverse effects associated with the worsening of the fresh properties; reduced permeability was mainly attributed to the refining of the pore network induced by the presence of GO.

Hydrophobic and oleophilic Si-based cotton fabrics have recently gained a lot of attention in oil/water separation due to their high efficiency. In this study, we present the effect of O2 plasma pre-treatment on the final properties of two Si-based cotton membranes obtained from dip coating and plasma polymerization, using polydimethylsiloxane (PDMS) as starting polymeric precursor. The structural characterizations indicate the presence of Si bond on both the modified cotton surfaces, with an increase of the carbon bond, assuring the success in surface modification. On the other hand, employing O2 plasma strongly changes the cotton morphology, inducing specific roughness and affecting the hydrophobicity durability and separation efficiency. In particular, the wettability has been retained after 20 laundry tests at 40 °C and 80 °C, and, for separation efficiency, even after 30 cycles, an improvement in the range of 10–15%, both at room temperature and at 90 °C can be observed. These results clearly demonstrate that O2 plasma pre-treatment, an eco-friendly, non-toxic, solvent-free, and one-step method for inducing specific functionalities on surfaces, is very effective in enhancing the oil/water separation properties for Si-based cotton membranes, especially in combination with plasma polymerization procedure for Si-based deposition.

A tetra-n-butoxy zinc phthalocyanine (n-BuO)4ZnPc has been synthesized in a single step, starting from commercial precursors, and easily purified. The molecule can be solution processed to form an effective and inexpensive hole transport layer for organic and perovskite solar cells. These appealing features are suggested by the results of a series of chemical, optical, and voltammetric characterizations of the molecule, supported by the results of ab initio simulations. Preliminary measurements of (n-BuO)4ZnPc-methylammonium lead triiodide perovskite-based devices confirm such suggestion and indicate that the interface between the photoactive layer and the hole transporting layer is characterized by hole-extracting and electron-blocking properties, potentially competitive with those of other standards de facto in the field of organic hole transport materials, like the expensive Spiro-OMeTAD.

Increasing awareness of environmental concerns has strongly pushed the scientific community towards the search for new solutions for efficient removal of oils and organic solvents from water. Here, we report the preparation of multifunctional TiO2-coated melamine-formaldehyde (MF) sponges as absorbent material for oils and organic solvents in water. TiO2-coated MF sponges were fabricated through an environmentally friendly approach, consisting in a simple immersion of the sponge into an oleic acid-capped TiO2 nanoparticles dispersion. The adhesion of TiOle coating to the sponge was then improved by the deposition of a low surface energy diamond-like carbon (DLC) thin layer. Our results highlighted that the modified MF sponges possess superhydrophobic and oleophilic behaviour, inertness to corrosive environment, good durability and reusability. Furthermore, the superhydrophobic DLC/TiO2@sponges showed (1) novel self-cleaning properties towards an absorbed commercial organic dye (IR-270BKA, chosen as representative) under visible light irradiation and (2) enhanced flame-retardant behaviour respect to the pristine MF sponge. These findings point out an important added value of DLC/TiOle@sponges making them promising candidates for wastewater treatments.

This work focuses on the possible application of gold nanoparticles on flexible cotton fabric as acetone- and ethanol-sensitive substrates by means of impedance measurements. Specifically, citrate- and polyvinylpyrrolidone (PVP)-functionalized gold nanoparticles (Au NPs) were synthesized using green and well-established procedures and deposited on cotton fabric. A complete structural and morphological characterization was conducted using UV–VIS and Fourier transform infrared (FT–IR) spectroscopy, atomic force microscopy (AFM), and scanning electron microscopy (SEM). A detailed dielectric characterization of the blank substrate revealed interfacial polarization effects related to both Au NPs and their specific surface functionalization. For instance, by entirely coating the cotton fabric (i.e., by creating a more insulating matrix), PVP was found to increase the sample resistance, i.e., to decrease the electrical interconnection of Au NPs with respect to citrate functionalized sample. However, it was observed that citrate functionalization provided a uniform distribution of Au NPs, which reduced their spacing and, therefore, facilitated electron transport. Regarding the detection of volatile organic compounds (VOCs), electrochemical impedance spectroscopy (EIS) measurements showed that hydrogen bonding and the resulting proton migration impedance are instrumental in distinguishing ethanol and acetone. Such findings can pave the way for the development of VOC sensors integrated into personal protective equipment and wearable telemedicine devices. This approach may be crucial for early disease diagnosis based on nanomaterials to attain low-cost/low-end and easy-to-use detectors of breath volatiles as disease markers.