Explore the vast range of titles available.

Layered molybdenum disulfide has demonstrated great promise as a low-cost alternative to platinum-based catalysts for electrochemical hydrogen production from water. Research effort on this material has focused mainly on synthesizing highly nanostructured molybdenum disulfide that allows the exposure of a large fraction of active edge sites. Here we report a promising microwave-assisted strategy for the synthesis of narrow molybdenum disulfide nanosheets with edge-terminated structure and a significantly expanded interlayer spacing, which exhibit striking kinetic metrics with onset potential of −103 mV, Tafel slope of 49 mV per decade and exchange current density of 9.62 × 10 −3 mA cm −2 , performing among the best of current molybdenum disulfide catalysts. Besides benefits from the edge-terminated structure, the expanded interlayer distance with modified electronic structure is also responsible for the observed catalytic improvement, which suggests a potential way to design newly advanced molybdenum disulfide catalysts through modulating the interlayer distance. Layered molybdenum disulfide is a promising hydrogen evolution catalyst. Here, the authors report a strategy for synthesizing molybdenum disulfide nanosheets with edge-terminated structure and a significantly expanded interlayer spacing and demonstrate their enhanced catalytic activity.

Recently developed solid-state catalysts can mediate carbon dioxide (CO 2 ) electroreduction to valuable products at high rates and selectivities. However, under commercially relevant current densities of > 200 milliamperes per square centimeter (mA cm −2 ), catalysts often undergo particle agglomeration, active-phase change, and/or element dissolution, making the long-term operational stability a considerable challenge. Here we report an indium sulfide catalyst that is stabilized by adding zinc in the structure and shows dramatically improved stability. The obtained ZnIn 2 S 4 catalyst can reduce CO 2 to formate with 99.3% Faradaic efficiency at 300 mA cm −2 over 60 h of continuous operation without decay. By contrast, similarly synthesized indium sulfide without zinc participation deteriorates quickly under the same conditions. Combining experimental and theoretical studies, we unveil that the introduction of zinc largely enhances the covalency of In-S bonds, which “locks” sulfur—a catalytic site that can activate H 2 O to react with CO 2 , yielding HCOO* intermediates—from being dissolved during high-rate electrolysis. Developing durable catalysts for carbon dioxide reduction to formate at commercial-scale current densities is challenging. This work reports that indium sulfide stabilized through zinc incorporation can produce formate efficiently and quickly at high current densities over long timescales.

Operating fuel cells in alkaline environments permits the use of platinum-group-metal-free (PGM-free) catalysts and inexpensive bipolar plates, leading to significant cost reduction. Of the PGM-free catalysts explored, however, only a few nickel-based materials are active for catalyzing the hydrogen oxidation reaction (HOR) in alkali; moreover, these catalysts deactivate rapidly at high anode potentials owing to nickel hydroxide formation. Here we describe that a nickel–tungsten–copper (Ni 5.2 WCu 2.2 ) ternary alloy showing HOR activity rivals Pt/C benchmark in alkaline electrolyte. Importantly, we achieved a high anode potential up to 0.3 V versus reversible hydrogen electrode on this catalyst with good operational stability over 20 h. The catalyst also displays excellent CO-tolerant ability that Pt/C catalyst lacks. Experimental and theoretical studies uncover that nickel, tungsten, and copper play in synergy to create a favorable alloying surface for optimized hydrogen and hydroxyl bindings, as well as for the improved oxidation resistance, which result in the HOR enhancement. The lack of efficient and cost-effective catalysts for H 2 oxidation reaction (HOR) hinders the application of anion exchange membrane fuel cells. Here, authors report a ternary nickel-tungsten-copper nanoalloy with marked HOR activity and stability that rivals the benchmark platinum catalyst.

The electroreduction of water for sustainable hydrogen production is a critical component of several developing clean-energy technologies, such as water splitting and fuel cells. However, finding a cheap and efficient alternative catalyst to replace currently used platinum-based catalysts is still a prerequisite for the commercialization of these technologies. Here we report a robust and highly active catalyst for hydrogen evolution reaction that is constructed by in situ growth of molybdenum disulfide on the surface of cobalt diselenide. In acidic media, the molybdenum disulfide/cobalt diselenide catalyst exhibits fast hydrogen evolution kinetics with onset potential of −11 mV and Tafel slope of 36 mV per decade, which is the best among the non-noble metal hydrogen evolution catalysts and even approaches to the commercial platinum/carbon catalyst. The high hydrogen evolution activity of molybdenum disulfide/cobalt diselenide hybrid is likely due to the electrocatalytic synergistic effects between hydrogen evolution-active molybdenum disulfide and cobalt diselenide materials and the much increased catalytic sites. There is substantial research into new catalysts for electroreduction of water. Here, the authors report a robust and active molybdenum disulfide/cobalt diselenide hydrogen evolution catalyst with onset potential of 11 mV and Tafel slope of 36 mV per decade, approaching the activity of platinum.

Simultaneously improving the activity and stability of catalysts for anodic oxygen evolution reaction (OER) in proton exchange membrane water electrolysis (PEMWE) remains a notable challenge. Here, we report a chromium-doped ruthenium dioxide with oxygen vacancies, termed Cr 0.2 Ru 0.8 O 2-x , that drives OER with an overpotential of 170 mV at 10 mA cm −2 and operates stably over 2000 h in acidic media. Experimental and theoretical studies show that the synergy of Cr dopant and oxygen vacancy induces an unconventional dopant-mediated hydroxyl spillover mechanism. Such dynamic hydroxyl spillover from Cr dopant to Ru active site changes the rate-determining step from OOH* formation to O 2 formation and thus greatly improves the OER performance. Moreover, the Cr dopant and oxygen vacancy also play a crucial role in stabilizing surface Ru and lattice oxygen in the Ru-O-Cr structural motif. When assembled into the anode of a practical PEMWE device, Cr 0.2 Ru 0.8 O 2-x enables long-term durability of over 200 h at an ampere-level current density and 60 degrees centigrade. Developing highly active and stable anode catalysts for green hydrogen production is crucial but challenging. Here, the authors report a Cr0.2Ru0.8O2-x catalyst with an unconventional dopant-mediated hydroxyl spillover mechanism for high-efficiency proton exchange membrane water electrolysis.

Transition metal dichalcogenide materials have been explored extensively as catalysts to negotiate the hydrogen evolution reaction, but they often run at a large excess thermodynamic cost. Although activating strategies, such as defects and composition engineering, have led to remarkable activity gains, there remains the requirement for better performance that aims for real device applications. We report here a phosphorus-doping-induced phase transition from cubic to orthorhombic phases in CoSe 2 . It has been found that the achieved orthorhombic CoSe 2 with appropriate phosphorus dopant (8 wt%) needs the lowest overpotential of 104 mV at 10 mA cm −2 in 1 M KOH, with onset potential as small as −31 mV. This catalyst demonstrates negligible activity decay after 20 h of operation. The striking catalysis performance can be attributed to the favorable electronic structure and local coordination environment created by this doping-induced structural phase transition strategy. Transition metal dichalcogenides represent an exciting class of earth-abundant hydrogen-from-water electrocatalysts, although low efficiencies limit commercialization. Here, authors present a doping strategy to induce a phase transition in cobalt selenide and boost H 2 -evolution performance.

Hydroxide exchange membrane fuel cells offer possibility of adopting platinum-group-metal-free catalysts to negotiate sluggish oxygen reduction reaction. Unfortunately, the ultrafast hydrogen oxidation reaction (HOR) on platinum decreases at least two orders of magnitude by switching the electrolytes from acid to base, causing high platinum-group-metal loadings. Here we show that a nickel-molybdenum nanoalloy with tetragonal MoNi 4 phase can catalyze the HOR efficiently in alkaline electrolytes. The catalyst exhibits a high apparent exchange current density of 3.41 milliamperes per square centimeter and operates very stable, which is 1.4 times higher than that of state-of-the-art Pt/C catalyst. With this catalyst, we further demonstrate the capability to tolerate carbon monoxide poisoning. Marked HOR activity was also observed on similarly designed WNi 4 catalyst. We attribute this remarkable HOR reactivity to an alloy effect that enables optimum adsorption of hydrogen on nickel and hydroxyl on molybdenum (tungsten), which synergistically promotes the Volmer reaction. The lack of efficient and cost-effective catalysts for hydrogen oxidation reaction (HOR) hampers the application of hydroxide exchange membrane fuel cells. Here, authors reported bimetallic MoNi 4 and WNi 4 nanoalloys with marked HOR activity in alkali, among which MoNi4 outperforms the Pt/C catalyst.

Perovskites with exsolved nanoparticles (P-eNs) have immense potentials for carbon dioxide (CO 2 ) reduction in solid oxide electrolysis cell. Despite the recent achievements in promoting the B-site cation exsolution for enhanced catalytic activities, the unsatisfactory stability of P-eNs at high voltages greatly impedes their practical applications and this issue has not been elucidated. In this study, we reveal that the formation of B-site vacancies in perovskite scaffold is the major contributor to the degradation of P-eNs; we then address this issue by fine-regulating the B-site supplement of the reduced Sr 2 Fe 1.3 Ni 0.2 Mo 0.5 O 6- δ using foreign Fe sources, achieving a robust perovskite scaffold and prolonged stability performance. Furthermore, the degradation mechanism from the perspective of structure stability of perovskite has also been proposed to understand the origins of performance deterioration. The B-site supplement endows P-eNs with the capability to become appealing electrocatalysts for CO 2 reduction and more broadly, for other energy storage and conversion systems. The instability of perovskites with exsolved nanoparticles for CO 2 electrocatalysis impedes their practical applications. Here, the authors show the formation of B-site vacancies in perovskite substrate as a major contributor to the degradation and report a strategy to enhance the stability of the perovskites at high voltages.

The incorporation of defects, such as vacancies, into functional materials could substantially tailor their intrinsic properties. Progress in vacancy chemistry has enabled advances in many technological applications, but creating new type of vacancies in existing material system remains a big challenge. We show here that ionized nitrogen plasma can break bonds of iron-carbon-nitrogen-nickel units in nickel-iron Prussian blue analogues, forming unconventional carbon-nitrogen vacancies. We study oxygen evolution reaction on the carbon-nitrogen vacancy-mediated Prussian blue analogues, which exhibit a low overpotential of 283 millivolts at 10 milliamperes per square centimeter in alkali, far exceeding that of original Prussian blue analogues and previously reported oxygen evolution catalysts with vacancies. We ascribe this enhancement to the in-situ generated nickel-iron oxy(hydroxide) active layer during oxygen evolution reaction, where the Fe leaching was significantly suppressed by the unconventional carbon-nitrogen vacancies. This work opens up opportunities for producing vacancy defects in nanomaterials for broad applications. Defect-engineering offers a promising route to vary material properties and reactivities, although the achievable defect types are limited. Here, the authors introduced unusual CN-vacancies in Prussian blue analogue pre-catalysts that can limit Fe leaching and improve oxygen evolution performances.

Seawater electrolysis using renewable electricity offers an attractive route to sustainable hydrogen production, but the sluggish electrode kinetics and poor durability are two major challenges. We report a molybdenum nitride (Mo 2 N) catalyst for the hydrogen evolution reaction with activity comparable to commercial platinum on carbon (Pt/C) catalyst in natural seawater. The catalyst operates more than 1000 hours of continuous testing at 100 mA cm −2 without degradation, whereas massive precipitate (mainly magnesium hydroxide) forms on the Pt/C counterpart after 36 hours of operation at 10 mA cm −2 . Our investigation reveals that ammonium groups generate in situ at the catalyst surface, which not only improve the connectivity of hydrogen-bond networks but also suppress the local pH increase, enabling the enhanced performances. Moreover, a zero-gap membrane flow electrolyser assembled by this catalyst exhibits a current density of 1 A cm −2 at 1.87 V and 60 o C in simulated seawater and runs steadily over 900 hours. Efficient catalysts for seawater electrolysis are crucial for sustainable hydrogen production but struggle with slow kinetics and low durability. Here, the authors report a molybdenum nitride catalyst that in situ generates ammonium groups, enhancing both performance and stability in natural seawater.