Explore the vast range of titles available.

The celebrated electronic properties of graphene 1 , 2 have opened the way for materials just one atom thick 3 to be used in the post-silicon electronic era 4 . An important milestone was the creation of heterostructures based on graphene and other two-dimensional crystals, which can be assembled into three-dimensional stacks with atomic layer precision 5 , 6 , 7 . Such layered structures have already demonstrated a range of fascinating physical phenomena 8 , 9 , 10 , 11 , and have also been used in demonstrating a prototype field-effect tunnelling transistor 12 , which is regarded to be a candidate for post-CMOS (complementary metal-oxide semiconductor) technology. The range of possible materials that could be incorporated into such stacks is very large. Indeed, there are many other materials with layers linked by weak van der Waals forces that can be exfoliated 3 , 13 and combined together to create novel highly tailored heterostructures. Here, we describe a new generation of field-effect vertical tunnelling transistors where two-dimensional tungsten disulphide serves as an atomically thin barrier between two layers of either mechanically exfoliated or chemical vapour deposition-grown graphene. The combination of tunnelling (under the barrier) and thermionic (over the barrier) transport allows for unprecedented current modulation exceeding 1 × 10 6 at room temperature and very high ON current. These devices can also operate on transparent and flexible substrates. A tunnelling transistor based on stacks of chemically grown graphene and other two-dimensional layers shows record performance.

In this work, the relative dielectric permittivity of graphene oxide (GO), both its real and imaginary parts, have been measured under various humidity conditions at GHz. It is demonstrated that the relative dielectric permittivity increases with increasing humidity due to water uptake. This finding is very different to that at a couple of MHz or lower frequency, where the relative dielectric permittivity increases with decreasing humidity. This GO electrical property was used to create a battery-free wireless radio-frequency identification (RFID) humidity sensor by coating printed graphene antenna with the GO layer. The resonance frequency as well as the backscattering phase of such GO/graphene antenna become sensitive to the surrounding humidity and can be detected by the RFID reader. This enables battery-free wireless monitoring of the local humidity with digital identification attached to any location or item and paves the way for low-cost efficient sensors for Internet of Things (IoTs) applications.

The application of graphene in sensor devices depends on the ability to appropriately functionalize the pristine graphene. Here we show the direct writing of tailored phospholipid membranes on graphene using dip-pen nanolithography. Phospholipids exhibit higher mobility on graphene compared with the commonly used silicon dioxide substrate, leading to well-spread uniform membranes. Dip-pen nanolithography allows for multiplexed assembly of phospholipid membranes of different functionalities in close proximity to each other. The membranes are stable in aqueous environments and we observe electronic doping of graphene by charged phospholipids. On the basis of these results, we propose phospholipid membranes as a route for non-covalent immobilization of various functional groups on graphene for applications in biosensing and biocatalysis. As a proof of principle, we demonstrate the specific binding of streptavidin to biotin-functionalized membranes. The combination of atomic force microscopy and binding experiments yields a consistent model for the layer organization within phospholipid stacks on graphene. The sensitivity and selectivity of graphene-based biosensors depends on attaching various functional groups to graphene. Hirtz et al . use dip-pen nanolithography to directly write phospholipid membranes on graphene, which enables multiplexed and heterogeneous non-covalent functionalization.

Weak interlayer interactions in van der Waals crystals facilitate their mechanical exfoliation to monolayer and few-layer two-dimensional materials, which often exhibit striking physical phenomena absent in their bulk form. Here we utilize mechanical exfoliation to produce a two-dimensional form of a mineral franckeite and show that the phase segregation of chemical species into discrete layers at the sub-nanometre scale facilitates franckeite’s layered structure and basal cleavage down to a single unit cell thickness. This behaviour is likely to be common in a wider family of complex minerals and could be exploited for a single-step synthesis of van der Waals heterostructures, as an alternative to artificial stacking of individual two-dimensional crystals. We demonstrate p-type electrical conductivity and remarkable electrochemical properties of the exfoliated crystals, showing promise for a range of applications, and use the density functional theory calculations of franckeite’s electronic band structure to rationalize the experimental results. Layered materials are held together by weak van der Waals forces facilitating layer-by-layer cleavage. Here, the authors demonstrate mechanical exfoliation of a naturally occurring franckeite mineral heterostructure, possessing p-type conductivity and remarkable electrochemical properties.

Forecasting volcanic ash atmospheric pathways is of utmost importance for aviation. Volcanic ash can interfere with aircraft navigational instruments and can damage engine parts. Early warning systems, activated after volcanic eruptions can alleviate the impacts on aviation by providing forecasts of the volcanic ash plume dispersion. The quality of these short-term forecasts is subject to the accuracy of the meteorological wind fields used for the initialization of regional models. Here, we use wind profiling data from the first high spectral resolution lidar in space, Aeolus, to examine the impact of measured wind fields on regional NWP and subsequent volcanic ash dispersion forecasts, focusing on the case of Etna’s eruption on March 2021. The results from this case study demonstrate a significant improvement of the volcanic ash simulation when using Aeolus-assimilated meteorological fields, with differences in wind speed reaching up to 8 m/s when compared to the control run. When comparing the volcanic ash forecast profiles with downwind surface-based aerosol lidar observations, the modeled field is consistent with the measurements only when Aeolus winds are assimilated. This result clearly demonstrates the potential of Aeolus and highlights the necessity of future wind profiling satellite missions for improving volcanic ash forecasting and hence aviation safety.

North Africa, the Middle East, and Europe (NAMEE domain) host a variety of suspended particles characterized by different optical and microphysical properties. In the current study, we investigate the importance of the lidar ratio (LR) on Cloud-Aerosol Lidar with Orthogonal Polarization–Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIOP-CALIPSO) aerosol retrievals towards assessing aerosols’ impact on the Earth-atmosphere radiation budget. A holistic approach has been adopted involving collocated Aerosol Robotic Network (AERONET) observations, Radiative Transfer Model (RTM) simulations, as well as reference radiation measurements acquired using spaceborne (Clouds and the Earth’s Radiant Energy System-CERES) and ground-based (Baseline Surface Radiation Network-BSRN) instruments. We are assessing the clear-sky shortwave (SW) direct radiative effects (DREs) on 550 atmospheric scenes, identified within the 2007–2020 period, in which the primary tropospheric aerosol species (dust, marine, polluted continental/smoke, elevated smoke, and clean continental) are probed using CALIPSO. RTM runs have been performed relying on CALIOP retrievals in which the default and the DeLiAn (Depolarization ratio, Lidar ratio, and Ångström exponent)-based aerosol-speciated LRs are considered. The simulated fields from both configurations are compared against those produced when AERONET AODs are applied. Overall, the DeLiAn LRs leads to better results mainly when mineral particles are either solely recorded or coexist with other aerosol species (e.g., sea-salt). In quantitative terms, the errors in DREs are reduced by ~26–27% at the surface (from 5.3 to 3.9 W/m2) and within the atmosphere (from −3.3 to −2.4 W/m2). The improvements become more significant (reaching up to ~35%) for moderate-to-high aerosol loads (AOD ≥ 0.2).

Vertically retrieved optical properties by Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) were investigated in the case of three selected events over Athens and Thessaloniki with documented high pollen concentrations. Hirst-type volumetric samplers were used to detect and characterize the pollen during the CALIPSO overpasses. Only cases with a total pollen concentration greater than 400 grains m−3 for at least two hours per day were considered severe pollen events, while model simulations were used to exclude the presence of other depolarizing aerosol types. This study provides mean values of lidar-derived optical properties inside the detected pollen layers; i.e., optical values represent the atmosphere with the presence of pollen, in urban cities of Greece. Specifically, three observed aerosol layers, one over Athens and two over Thessaloniki with particulate color ratios of 0.652 ± 0.194, 0.638 ± 0.362, and 0.456 ± 0.284, and depolarization ratios of 8.70 ± 6.26%, 28.30 ± 14.16%, and 8.96 ± 6.87%, respectively, were misclassified by CALIPSO as marine-dusty marine, dust, and polluted dust. In cases of intense pollen presence, CALIPSO vertical profiles and aerobiological monitoring methods may be used synergistically to better characterize the atmospheric pollen layers.

The use of two-dimensional materials in bulk functional applications requires the ability to fabricate defect-free 2D sheets with large aspect ratios. Despite huge research efforts, current bulk exfoliation methods require a compromise between the quality of the final flakes and their lateral size, restricting the effectiveness of the product. In this work, we describe an intercalation-assisted exfoliation route, which allows the production of high-quality graphene, hexagonal boron nitride, and molybdenum disulfide 2D sheets with average aspect ratios 30 times larger than that obtained via conventional liquid-phase exfoliation. The combination of chlorosulfuric acid intercalation with in situ pyrene sulfonate functionalisation produces a suspension of thin large-area flakes, which are stable in various polar solvents. The described method is simple and requires no special laboratory conditions. We demonstrate that these suspensions can be used for fabrication of laminates and coatings with electrical properties suitable for a number of real-life applications.

The Mediterranean, and particularly its Eastern basin, is a crossroad of air masses advected from Europe, Asia and Africa. Anthropogenic emissions from its megacities meet over the Eastern Mediterranean, with natural emissions from the Saharan and Middle East deserts, smoke from frequent forest fires, background marine and pollen particles emitted from ocean and vegetation, respectively. This mixture of natural aerosols and gaseous precursors (Short-Lived Climate Forcers—SLCFs in IPCC has short atmospheric residence times but strongly affects radiation and cloud formation, contributing the largest uncertainty to estimates and interpretations of the changing cloud and precipitation patterns across the basin. The SLCFs’ global forcing is comparable in magnitude to that of the long-lived greenhouse gases; however, the local forcing by SLCFs can far exceed those of the long-lived gases, according to the Intergovernmental Panel on Climate Change (IPCC). Monitoring the spatiotemporal distribution of SLCFs using remote sensing techniques is important for understanding their properties along with aging processes and impacts on radiation, clouds, weather and climate. This article reviews the current state of scientific know-how on the properties and trends of SLCFs in the Eastern Mediterranean along with their regional interactions and impacts, depicted by ground- and space-based remote sensing techniques.

We report the gate-modulated Raman spectrum of defective graphene. We show that the intensity of the D peak can be reversibly tuned by applying a gate voltage. This effect is attributed to chemical functionalization of the graphene crystal lattice, generated by an electrochemical reaction involving the water layer trapped at the interface between silicon and graphene.