Explore the vast range of titles available.

Improved methods for the extraction of eicosapentaenoic acid (EPA), an essential and economically important polyunsaturated fatty acid, are urgently required. However, lipid extraction rates using food-grade solvents such as ethanol are usually low. To improve the ethanol-based extraction rate, and to elucidate the relevant mechanisms, we used cellulase and laccase to treat powdered Nannochloropsis, one of the most promising microalgal sources of EPA. Cellulase and laccase synergistically increased lipid yields by 69.31% and lipid EPA content by 42.63%, by degrading the amorphous hemicellulose and cellulose, improving crystallinity, and promoting the release and extraction of lysodiacylglyceryltrimethylhomoserine. Scanning electron microscopy showed that cell morphology was substantially altered, with cell-wall rupture, loss of cell boundaries, and the release of intracellular substances. In conclusion, Nannochloropsis lipid yields may be directly linked to cell-wall hemicellulose structure, and enzymatic treatment to alter this may improve lipid yields.

In this study, we investigated and compared the oil yield, physicochemical properties, fatty acid composition, nutrient content, and antioxidant ability of Xanthoceras sorbifolia Bunge (X. sorbifolia) kernel oils obtained by cold-pressing (CP), hexane extraction (HE), aqueous enzymatic extraction (AEE), and supercritical fluid extraction (SFE). The results indicated that X. sorbifolia oil contained a high percentage of monounsaturated fatty acids (49.31–50.38%), especially oleic acid (30.73–30.98%) and nervonic acid (2.73–3.09%) and that the extraction methods had little effect on the composition and content of fatty acids. X. sorbifolia oil is an excellent source of nervonic acid. Additionally, the HE method resulted in the highest oil yield (98.04%), oxidation stability index (9.20 h), tocopherol content (530.15 mg/kg) and sterol content (2104.07 mg/kg). The DPPH scavenging activity rates of the oil produced by SFE was the highest. Considering the health and nutritional value of oils, HE is a promising method for X. sorbifolia oil processing. According to multiple linear regression analysis, the antioxidant capacity of the oil was negatively correlated with sterol and stearic acid content and positively correlated with linoleic acid, arachidic acid and polyunsaturated fatty acid content. This information is important for improving the nutritional value and industrial production of X. sorbifolia.

This study aimed to obtain a rice bran blended oil with good quality in deep frying. The thermal stability, nutrients and harmful substances of rice bran oil (RBO) and other four oils (palm oil, PO; cottonseed oil, CO; sunflower oil, SuO; soybean oil, SO) were analyzed. Besides, the blended oil formulas were established by the principal component analysis method, and their physicochemical properties, frying characteristic indicators, nutrients, and harmful substances were compared. The results provided that two suitable blended oil formulas (F1: 50% RBO + 40% PO + 10% CO; F2: 60% RBO + 35% PO + 5% CO) of good frying performance were attained by principal component analysis. The acid value (1.19 mg/g), peroxide value (0.09 meq/kg), residual oil rate (8.07%), 3-MCPD ester reduction content (2.33 mg/kg), benzopyrene concentration content (0.95 μg/kg) and vitamin E consumption rate (67.86%) in F2 were lower than that in F1. Moreover, the oryzanol retention rate (87.84%) of F2 was higher than that of F1. In summary, F2 was more conducive to human health and more suitable than F1 in deep-frying. This information had an important directive on the industrial production of rice bran blend oil.

This study investigated the effects of three extraction methods, including cold pressing (CP), microwave pretreatment pressing (MP), and supercritical fluid extraction (SFE), on the yield, physicochemical properties, bioactive compounds content, and antioxidant properties of pumpkin seed oil (PSO). Furthermore, the correlation between bioactive compounds and the antioxidant properties of PSO was determined. The results revealed that the yield of PSO extracted using the three methods was in the order of SFE > MP > CP. Additionally, the PSO generated by SFE showed the highest unsaturated fatty acid content, followed by MP and CP. Additionally, MP-PSO exhibited the highest acid value and saponification value, while SFE-PSO displayed the highest moisture content, peroxide value, and iodine value. Moreover, the PSO generated by MP demonstrated superior antioxidant properties compared to that of PSOs from CP and SFE in the oxidation induction, DPPH, FRAP, and ABTS tests. Finally, the correlation analysis revealed that specific types of bioactive compounds, such as β-sitosterol and γ-tocopherol, were highly correlated with the antioxidant properties of PSOs. Consequently, this study provides comprehensive knowledge regarding PSO extraction, physicochemical properties, bioactive compound extraction, and the correlated antioxidant properties.

This study was the first time the effects of pretreatment technology (microwave roasting, MR; oven roasting, OR; steaming roasting, SR) and processing technology (screw pressing, SP; aqueous enzymatic extraction, AEE; subcritical butane extraction, SBE) on the quality (physicochemical properties, phytochemical content, and antioxidant ability) of walnut oil were systematically compared. The results showed that the roasting pretreatment would reduce the lipid yield of walnut oil and SBE (59.53–61.19%) was the processing method with the highest yield. SR-AEE oil provided higher acid value (2.49 mg/g) and peroxide value (4.16 mmol/kg), while MR-SP oil had the highest content of polyunsaturated fatty acid (73.69%), total tocopherol (419.85 mg/kg) and total phenolic compounds (TPC, 13.12 mg/kg). The DPPH-polar and ABTS free radicals’ scavenging abilities were accorded with SBE > AEE > SP. SBE is the recommended process for improving the extraction yield and antioxidant ability of walnut oil. Hierarchical cluster analysis showed that processing technology had a greater impact on walnut oil than pretreatment technology. In addition, multiple linear regression revealed C18:0, δ-tocopherol and TPC had positive effects on the antioxidant ability of walnut oil, while C18:1n-9, C18:3n-3 and γ-tocopherol were negatively correlated with antioxidant activity. Thus, this a promising implication for walnut oil production.

Pumpkin seed oil (PSO) is becoming increasingly valued for its nutritional profile and minor bioactive constituents. Here, we surveyed PSOs marketed in China and hypothesized that differences in antioxidant constituents help explain variability in oxidative stability across brands. Sixteen commercial products labeled as pumpkin (Cucurbita moschata Duchesne) seed oils, including two imported brands (France), were analyzed for physicochemical quality indices, fatty acid composition, oxidative stability, and bioactive components (tocopherols, total sterols, and total phenolics expressed as gallic acid equivalents). Acid value, peroxide value, and iodine value ranged from 0.22 to 4.30 mg KOH/g, from 4.63 to 11.57 mEq O2/kg, and from 106.64 to 132.77 g I2/100 g, respectively, and all samples complied with applicable regulatory limits. Oleic and linoleic acids predominated (21.79–35.50% and 44.99–57.03% of total fatty acids, respectively), consistent with a highly unsaturated oil matrix. Total phenolics varied widely, reaching 2247.78 mg GAE/kg, while total tocopherols and total sterols ranged from 268.26 to 528.26 mg/kg and 733.64 to 1095.99 mg/kg, respectively. Oxidation induction times ranged from approximately 4 to over 10 h, and radical-scavenging activity differed markedly among samples. Correlation analysis and principal component analysis consistently identified δ-tocopherol, total sterols, and total phenolics as the variables most strongly associated with oxidative stability and antioxidant performance. Overall, these results provide a market-level snapshot of compositional variability in PSOs sold in China and highlight antioxidant-related markers that may support quality differentiation and process optimization.

Annealing is a commonly used post-processing method for composite thin strips but suffers from drawbacks such as long processing time, high energy consumption, and susceptibility to oxidation. Replacing annealing with electric pulse treatment (EPT) can address these issues. In this study, a specially designed fixture was used to investigate the effects of pulsed current on the bonding strength of T2 copper (Cu)/304 stainless steel (SS) composite thin strips. The initial strip, with a 50% reduction rate, was prepared using a two-high mill, resulting in a Cu/SS composite strip with a thickness of 0.245 mm. Pulsed current treatment was applied with peak temperatures ranging from 350 °C to 600 °C. The results showed that EPT significantly improved the bonding strength. A pulsed current of 55 A resulted in the highest average peel strength of 10.66 ± 0.93 N/mm, with a maximum Fe content on the Cu side of 7.39 ± 0.84%, while a pulsed current of 65 A resulted in the highest Cu content on the SS side, reaching 57.54 ± 2.06%. This study demonstrates that EPT effectively controls the deformation behavior and interface state of composite strips, producing Cu/SS composite thin strips with high bonding strength.

Camellia seed oil (CSO), as a nutrient-rich edible oil, is widely used in foods, cosmetics, and other fields. In this work, the extraction, deacidification, decolorization, and deodorization processes of CSO were respectively optimized for meeting injectable oil standards. The results showed that the CSO extraction rate reached the highest level of 94% at optimized conditions (ultrasonic time, 31.2 min; reaction pH, 9.2; and reaction time, 3.5 h). The physicochemical indexes of CSO and 10 other vegetable oils were evaluated by the principal component analysis method, and the overall scores of vegetable oils were ranked as camellia seed oil > olive oil > rice oil > peanut oil > sesame oil > corn oil > soybean oil > sunflower oil > rapeseed oil > walnut oil > flaxseed oil. The physicochemical indicators of CSO were the most ideal among the 11 vegetable oils, which means that CSO is suitable as an injectable oil. Through the optimized processes of the deacidification, decolorization, and deodorization, the CSO acid value was reduced to 0.0515 mg KOH/g, the decolorization rate reached a maximum of 93.86%, and the OD430 was 0.015, meeting the requirement (≤0.045 of OD430) of injectable oil. After the deodorization process, these parameters of the refractive index, acid value, saponification value, iodine value, absorbance, unsaponifiable, moisture and volatiles, fatty acid composition, and heavy metal limits all met the pharmacopoeia standards of injectable oil in many countries and regions. The possibility of CSO as an injectable oil was first verified through refining-process optimization and nutritional index analysis, providing an important technical reference for the high-value utilization of vegetable oil.

In this study, the whey protein isolate–high-methoxyl pectin (WPI-HMP) complex prepared by electrostatic interaction was utilized as an emulsifier in the preparation of docosahexaenoic acid (DHA) algal oils in order to improve their physicochemical properties and oxidation stability. The results showed that the emulsions stabilized using the WPI-HMP complex across varying oil-phase volume fractions (30–70%) exhibited consistent particle size and enhanced stability compared to emulsions stabilized solely using WPI or HMP at different ionic concentrations and heating temperatures. Furthermore, DHA algal oil emulsions stabilized using the WPI-HMP complex also showed superior storage stability, as they exhibited no discernible emulsification or oil droplet overflow and the particle size variation remained relatively minor throughout the storage at 25 °C for 30 days. The accelerated oxidation of the emulsions was assessed by measuring the rate of DHA loss, lipid hydroperoxide levels, and malondialdehyde levels. Emulsions stabilized using the WPI-HMP complex exhibited a lower rate of DHA loss and reduced levels of lipid hydroperoxides and malondialdehyde. This indicated that WPI-HMP-stabilized Pickering emulsions exhibit a greater rate of DHA retention. The excellent stability of these emulsions could prove valuable in food processing for DHA nutritional enhancement.

As a crucial asset for human health and modern medicine, an increasing number of biotherapeutics are entering the clinic. However, due to their complexity, these drugs have a higher potential to be immunogenic, leading to the generation of anti-drug antibodies (ADAs). Clinically significant ADAs have an impact on pharmacokinetics (PK), pharmacodynamics (PD), effectiveness, and/or safety. Thus, it is crucial to understand, manage and minimize the immunogenicity potential during drug development, ideally starting from the molecule design stage. In this study, we utilized various immunogenicity risk assessment methods, including prediction, dendritic cell internalization, MHC-associated peptide proteomics, HLA peptide binding, and T cell proliferation, to assess the immunogenicity risk of FLT3L-Fc variants. We identified a single point mutation in the human FLT3L-Fc protein that introduced highly immunogenic T cell epitopes, leading to the induction of T cell responses and thereby increasing the immunogenicity risk in clinical settings. Consequently, the variant with this point mutation was removed from further consideration as a clinical candidate. This finding underscores the necessity for careful evaluation of mutations during the engineering of protein therapeutics. The integration of multiple immunogenicity risk assessment tools offers critical insights for informed decision-making in candidate sequence design and therapeutic lead selection.