Explore the vast range of titles available.

Background The use of all-suture anchors (ASA) for treating bony Bankart lesions remains challenging because of the limited availability of cortical bone for secure fixation. In this study, the mechanical properties of transosseous ASA fixation, wherein the anchor is placed through the far cortex, were compared with those of metallic suture anchors and standard ASA fixation. Methods For this controlled experimental study, 24 suture anchors were inserted into 12 synthetic scapulae with simulated bony Bankart lesions, with two anchors placed in each scapula. The scapulae were randomly assigned to Group A (two 2.7-mm metallic anchors), Group B (two 1.3-mm ASAs secured through standard fixation), or Group C (two 1.3-mm ASAs secured transosseously). For biomechanical analysis, a 5 N preload was applied for 2 min, followed by cyclic loading from 5 to 25 N at 1 Hz for 100 cycles. In addition, a load-to-failure test was conducted at a rate of 60 mm/min. Displacement, stiffness, ultimate failure load, and failure mode were recorded. Results There were no significant differences and low correlations in biomechanical properties between the two anchors placed in each scapula. Nor significant intergroup differences were noted in cyclic displacement or linear stiffness. Group C exhibited a significantly higher ( P  < 0.001) ultimate failure load (176.8 ± 32.7 N) than did with Group A (104.4 ± 17.5 N) and Group B (83.0 ± 10.8 N). All failures resulted from anchor pullout, except for two cases in Group C, where deformed suture balls were observed without pullout. Conclusion Compared with metallic suture anchors and standard ASA fixation, transosseous ASA fixation significantly improved the maximum failure load in a bony Bankart lesion model, without increasing cyclic displacement. Level of evidence Basic Science Study; Biomechanics.

Background With an increase in the elderly population, the occurrence of hip fractures, femoral neck fractures, and intertrochanteric fractures (ITFs) is also increasing. It is important to establish effective perioperative methods that would help reduce the morbidity and mortality rates associated with ITFs. The purpose of this study was to determine the effects of ITFs according to the AO classification for perioperative hemoglobin drop. Methods Seventy-six patients with ITFs classified as AO 31-A1 or A2 and fixated with intramedullary nails participated in this retrospective cohort study. Medical records of these patients were retrospectively reviewed from September 2016 to August 2018. The perioperative hemoglobin drop was chosen as the main outcome measure and calculated as the difference between pre- and postoperative hemoglobin levels. Multivariate linear regression analysis was performed and included the following variables: AO classification (A1.1-A2.1 [stable] vs. A2.2-A2.3 [unstable]), time interval between injury and surgery, age, body mass index, and the use of anticoagulants. Results Among the 76 patients who met the inclusion criteria, a significantly higher hemoglobin drop was observed in the AO 31 A2.2-A2.3 (unstable) group than in the AO 31 A1.1-A2.1 (stable) group ( p  = 0.04). The multivariate analysis also showed a greater hemoglobin drop in the unstable group ( p  < 0.05). Conclusions Patients with unstable ITFs exhibited a greater hemoglobin drop and a hidden blood loss was suspected around the fracture site. We believe that this should be taken into consideration when presurgical blood transfusion is being planned for patients with unstable ITFs, to reduce associated postoperative complications, especially in patients with severe anemia or high risk of mortality.

Background The treatment of Hoffa fractures is challenging, for which the ideal fixation and approach are still controversial. Osteosynthesis with plate or screws fixation in different trajectories have been described in previous literature. The purpose of this study was to compare the biomechanical strength and stability of two types of screw trajectories used to stabilize displaced coronal fractures of the lateral femoral condyle. Methods Sixteen synthetic femurs (Sawbones Pacific Research Laboratories, Vashon, WA) were divided into two groups. A vertical osteotomy was performed to mimic a Letenneur type I Hoffa fracture. Group A ( n  = 8) was fixed with screw in anteroposterior direction (A-P) screws. Group B ( n  = 8) was fixed with crossed screws. Both groups were tested with a nondestructive axial compression aligned with the femur axis. After that, 10,000 cyclic loading tests were applied to the specimen with a force ranging between 200 to 600 N, and the interfragmental displacement was recorded, respectively, after 10, 100, 1000 and 10,000 cycles. Finally, a destructive axial compression test was applied until catastrophic failure. Results There were no statistical between-group differences in regard to the average axial stiffness, interfragmental displacement, and ultimate failure load. The average axial stiffness of the A-P screw was comparable to that of the crossed screw (361 ± 113 N/mm vs. 379 ± 65 N/mm, p  = 0.753). All specimens completed the entire cyclic loading test without catastrophic failure, and the interfragmental displacement after loading for 10,000 cycles was 1.36 ± 0.40 mm for the A-P screw and 1.29 ± 0.61 mm for the crossed screw, there were no statistical differences between the groups ( p  = 0.823). The average ultimate failure loads for the A-P and crossed screws were 1214 ± 127 N and 1109 ± 156 N, respectively ( p  = 0.172). Conclusions Based on our in vitro study, the crossed screws can provide comparable mechanical performance as traditional A-P screws in Hoffa fracture fixation. Considering the screws trajectories are commonly determined by the choice of surgical approach, the current study provides support from a biomechanical perspective for the application of crossed screws in direct lateral approach.

Background The patient self-report section of the American Shoulder and Elbow Surgeons Standardized Shoulder Assessment Form (ASESp) is one of the most validated and reliable assessment tools. This study aimed to establish a validated Chinese version of ASESp (ASESp-CH). Methods A clinical prospective study was performed (ClinicalTrials.gov Identifier: NCT04755049; registered on 2021/02/11). Following the guidelines of forward-backward translation and cross-cultural adaptation, a Chinese version of ASESp was established. Patients older than 18 years with shoulder disorders were included. Patients who could not complete test-retest questionnaires within the interval of 7–30 days and patients who received interventions were excluded. Intraclass correlation (ICC) was calculated for test- retest reliability, whereas internal consistency was determined by Cronbach value. Construct validity was evaluated by comparing the corresponding domains between the ASESp-CH and a validated Chinese version of 36-Item Short Form Health Survey (SF-36). Results A total of 86 patients were included with a mean test-retest interval of 12 ± 5.4 days. Test-retest reliability was excellent with an ICC of 0.94. Good internal consistency was found, with a Cronbach alpha of 0.86. Construct validity of the ASESp-CH questionnaire was good. The major domains of the ASESp-CH were significantly correlated with the respective domains in the SF-36 ( p  <  0.01), except for the domain of stability of ASESp-CH. Conclusions The Chinese version of ASESp questionnaire is a highly validated and reliable tool for shoulder disorder assessment.

Purpose To investigate the relationship between the lateral femoral notch sign as well as the coronal lateral collateral ligament (LCL) sign and anterior tibial translation using the GNRB arthrometer in patients with anterior cruciate ligament (ACL) injuries. Methods Forty-six patients with ACL injuries were retrospectively included from May 2020 to February 2022; four patients were excluded due to incomplete data. Magnetic resonance imaging (MRI) were reviewed for the lateral femoral notch sign and the coronal LCL sign. The GNRB arthrometer was used to evaluate the dynamic anterior tibial translation of the knee, and the side-to-side differences (SSDs) in tibial translation between the injured knee and healthy knee were calculated at different force levels. Two types of slopes for displacement-force curves were acquired. Results Six patients (14.3%) had the positive lateral femoral notch sign (notch depth > 2.0 mm), and 14 patients (33.3%) had the positive coronal LCL sign. The SSD of the anterior tibial translations under different loads as well as the slopes of displacement-force curves were the same in the positive and negative notch sign groups ( p all > 0.05) and between the positive and negative coronal LCL sign groups ( p all > 0.05). Meanwhile, the measured notch depth and notch length were also not significantly correlated with the anterior tibial translation SSD in the GNRB. Conclusion The presence of the lateral femoral notch sign and the coronal LCL sign did not indicate greater dynamic tibial laxity as measured using the GNRB.

Background The optimal surgical technique for the fixation of inferior pole patellar fracture remains controversial. The aims of this study were (1) to compare clinical and radiological outcomes following fixation of inferior pole patellar fracture by using tension band wire (TBW) and transosseous reattachment (TOR) without excision of the bony fragment and (2) to determine the risk factors for postoperative radiological loss of reduction. Methods For this retrospective cohort study, consecutive patients with inferior pole patellar fracture between January 2010 and December 2017 were recruited. The patients were grouped according to their fixation method (TBW or TOR), and demographic data, clinical outcomes, and postoperative Insall–Salvati (IS) ratio were analyzed. Then, the patients were grouped according to radiological loss of reduction, the possible risk factors for loss of reduction were identified, and odds ratios were calculated. Result This study included 55 patients with inferior pole patellar fracture; 30 patients were treated using TBW and 25 were treated using TOR. Clinical failure occurred in two patients in the TBW group (7%) and three in the TOR group (12%). The rate of radiological loss of reduction was significant higher in the TOR group, whereas removal of implants was significantly more common in the TBW group. Patella baja was noted immediately after surgery in the TOR group, but the IS ratios of the two groups were similar after 3 months. Fracture displacement of more than 30 mm was the only independent risk factor for postoperative radiological loss of reduction. Conclusion For treating inferior pole patellar fracture, both TWB and TOR were effective and had a low clinical failure rate. In 60% of patients undergoing TBW fixation, however, additional surgery was required to remove the implants. Patella baja occurred immediately following TOR, but the patellar height was similar to that in the TBW group after 3 months. Surgeons should be aware of the high risk of postoperative radiological loss of reduction, especially when the fracture displacement is more than 30 mm.

Purpose The present study aimed to propose a modified intra-articular transtendinous looped biceps tenodesis (mTLBT) using a suture anchor and to compare the functional outcomes and incidence of Popeye deformities between biceps tenotomy and mTLBT. Methods Medical records of patients who underwent either tenotomy or mTLBT for the long head of the biceps tendon (LHBT) lesion between January 2016 and April 2021 were retrospectively reviewed. The inclusion criteria were patients aged 40–70 years with LHBT pathologies, such as superior labrum anterior to posterior (SLAP) lesions > type II, LHBT pulley system rupture with bicipital instability, and intra-articular LHBT tear. The exclusion criteria were full-thickness supraspinatus tears, frozen shoulder, shoulder fracture, and postoperative traumatic events that affected the operated shoulder. All patients were followed up for at least 1 year. Popeye deformity, bicipital cramping pain, visual analog scale (VAS) pain score, and functional outcome scores (University of California at Los Angeles [UCLA] and American Shoulder and Elbow Surgeons [ASES] scores) were recorded. Fisher’s exact test and Chi-square test were used for categorical variables, whereas the Mann–Whitney U test was used for nonparametric variables. Results The mTLBT and tenotomy groups included 15 and 40 patients, respectively. The incidence of Popeye deformity and biceps cramping pain in the tenotomy group (52.5% and 50%, respectively) was significantly higher than that in the mTLBT group (13.3% and 20%, respectively) ( p  = 0.009 and p  = 0.045, respectively). The postoperative VAS, UCLA, and ASES scores were not significantly different between the two groups. One patient in the tenodesis group experienced metallic-anchor pullout. Conclusion mTLBT is an arthroscopic intra-articular top of the groove tenodesis that can be performed completely in the intra-articular space and is especially suitable for patients with an intact or partially torn rotator cuff. This technique is reliable for treating biceps pathologies as it results in similar functional outcome scores, lesser biceps cramping pain, and less frequent Popeye deformity compared to biceps tenotomy. Level of Evidence III.

Aim The incidence and characteristics of iatrogenic comminution (IC) are unknown, and the influence of IC on fracture union is unclear. This study was aimed to investigate the (1) incidence and characteristics of IC and (2) the outcomes of IC following antegrade interlocking nailing of simple femoral shaft fractures. Methods We retrospectively collected data on patients who experienced simple femoral shaft fractures and underwent antegrade interlocking nailing between February 2009 and December 2016. The incidence and characteristics of IC were examined. According to the presence of IC, patients were divided into two groups: an IC group and a non-IC (NIC) group. Demographic information and nonunion rates were compared between the two groups. Potential risk factors for IC (age, gender, body mass index (BMI), nail fit ratio, reduction technique, and greater trochanter nail entry) were analyzed using univariate and multivariate logistic regression. The aforementioned variables, along with IC occurrence, were also assessed as potential risk factors for nonunion at 12 and 24 months after operation using multivariate logistic regression. Results Of the 211 total patients, IC occurred in 20.9% ( n  = 44) of patients. Most ICs were found at the level of the isthmus, and involved the medial cortex. Compared with the NIC group, higher nonunion rates were observed in the IC group at 12 months (31.8% vs. 12.5%, p  = 0.002) and 24 months (18% vs. 6.5%, p  = 0.017) after surgery. Age older than 35 years old was related with the occurrence of IC in univariate analysis. Multivariate analysis found no risk factor associated with IC. Open reduction technique, IC occurrence and higher BMI were identified as the risk factors of nonunion at 12 months and 24 months after surgery in multivariate analysis. Conclusion IC is a non-rare complication in antegrade interlocking nailing of simple femoral shaft fractures and was associated with higher nonunion rate. Age older than 35 years old showed a trend toward increasing risk of iatrogenic fracture comminution. In multivariate analysis, open reduction technique, IC occurrence and higher BMI significantly correlated with fracture nonunion. Level of evidence Level IV.

Purpose Suture anchors are commonly used to repair rotator cuff tendons in arthroscopy surgery, and several anchor materials have been created to maximize pull-out strength and minimize iatrogenic damage. We hypothesized that all-suture anchors have biomechanical properties equivalent to those of conventional anchors. Our purpose is to compare the biomechanical properties of different anchors used for rotator cuff repair. Methods The Embase, PubMed, Cochrane, and Scopus databases were searched for biomechanical studies on various suture anchors. The search keywords included rotator cuff tears and suture anchors, and two authors conducted study a selection, risk of bias assessment, and data extraction. The failure load, stiffness, and displacement were calculated using the mean differences with 95% confidence intervals (CIs). Failure modes were estimated using summary odds ratios with 95% CIs. The surface under the cumulative ranking curve was used for the relative ranking probabilities. A sensitivity analysis was performed by excluding studies using synthetic bones. Results The polyetheretherketone (PEEK) ( p  < 0.001) and all-suture anchors ( p  < 0.001) had higher failure loads than the biocomposite anchors, whereas no significant difference was observed in stiffness among the anchors. The all-suture ( p  = 0.006) and biocomposite anchors ( p  < 0.001) had displacements higher than the metal anchors. The relative ranking of the included anchors in failure loads and displacement changed in sensitivity analysis. The meta-analysis did not find significant differences, but the relative ranking probabilities suggested that all-suture anchor had a higher rate of anchor pull-out and a lower rate of eyelet or suture breakage. In contrast, the metal anchors were associated with a higher number of eyelet breakage episodes. Conclusions All-suture anchors showed significantly higher failure loads than the biocomposite anchors and similar cyclic displacements to the biocomposite and PEEK anchors. There were no significant differences in stiffness between all-suture and conventional suture anchors. The relative ranking of biomechanical properties changed in sensitivity analysis, suggesting the potential effect of bone marrow density. Level of Evidence Level IV.

Background In treatment of chronic acromioclavicular (AC) joint dislocations, both the Weaver–Dunn procedure (WD) and CC ligament reconstruction (CCR) are recommended options due to the low possibility of healing of the coracoclavicular (CC) ligaments. The aim of this review was to determine whether CCR will yield favorable clinical and radiographic outcomes in the treatment of chronic AC dislocations. Method The Cochrane Library, EMBASE, and PubMed databases were searched for literature on chronic AC dislocations from data inception to June 30, 2021. Patient data were pooled using standard meta-analytic approaches. The Cochrane-Mantel–Haenszel method and variance-weighted means were used to analyze the outcomes. The Review Manager version 5.3 software (The Nordic Cochrane Centre, The Cochrane Collaboration, Copenhagen, Denmark) was used to calculate the heterogenicity, mean difference, and relative risk (RR) for all outcomes in the meta-analysis. Results The current analysis included four trials on this topic, and all AC joint dislocations were classified as Rockwood types III to VI. The pooled data showed that the CCR group had significantly better post-operative American Shoulder and Elbow Surgeons Shoulder (ASES) scores, Oxford Shoulder Scores (OSSs), and Nottingham Clavicle Scores (NCSs) than the WD group, with a significant difference ( p  < 0.001, p  = 0.020, and p  < 0.001, respectively). In terms of the post-operative Constant-Murley Scores (CMSs), there were no significant differences between the CCR group and the WD group ( p  = 0.100). The CCR group had significantly better post-operative abduction and flexion of the index shoulder than the WD group ( p  < 0.001 and p  < 0.001, respectively). In terms of radiological outcomes, the post-operative coracoclavicular distance (CCD) with a 10 kg load was smaller in the CCR group compared to that in the WD group ( p  < 0.001). The overall surgical wound infection rate was 11.6% in the WD group and 12.9% in the CCR, respectively ( p  = 0.82). Conclusion The CCR group had better clinical outcome scores in the ASES, OOS, NCS, abduction, flexion, and external rotation than the WD group. In terms of radiological outcomes, the CCR group showed less displacement in weight-loaded post-CCD than the WD group, which indicated that the CCR provided more stability and resistance to deformation forces.