Explore the vast range of titles available.

In the context of the ATHENA X-IFU Cryogenic AntiCoincidence detector (CryoAC) development, we have studied the thermalization properties of a 2 × 2 mm SQUID chip. The chip is glued on a front-end PCB and operated on the cold stage of a dilution refrigerator ( T BASE  < 20 mK). We performed thermal conductance measurements by using different materials to glue the SQUID chip on the PCB. These have been repeated in subsequent cryostat runs, to highlight degradation effects due to thermal cycles. Here, we present the results obtained by glues and greases widely used in cryogenic environments, i.e., GE 7031 Varnish Glue, Apiezon N Grease and Rubber Cement.

The X-ray Integral Field Unit (X-IFU) of the Advanced Telescope for High-ENergy Astrophysics (Athena) large-scale mission of ESA will provide spatially resolved high-resolution X-ray spectroscopy from 0.2 to 12 keV, with 5 ″  pixels over a field of view of 5 arc minute equivalent diameter and a spectral resolution of 2.5 eV (FWHM) up to 7 keV. The core scientific objectives of Athena drive the main performance parameters of the X-IFU. We present the current reference configuration of the X-IFU, and the key issues driving the design of the instrument.

The X-IFU is the cryogenic spectrometer onboard the future ATHENA X-ray observatory. It is based on a large array of TES microcalorimeters, which work in combination with a Cryogenic AntiCoincidence detector (CryoAC). This is necessary to reduce the particle background level thus enabling part of the mission science goals. Here we present the first joint test of X-IFU TES array and CryoAC Demonstration Models, performed in a FDM setup. We show that it is possible to operate properly both detectors, and we provide a preliminary demonstration of the anti-coincidence capability of the system achieved by the simultaneous detection of cosmic muons.

The Cryogenic AntiCoincidence detector (CryoAC) of ATHENA X-IFU is designed to reduce the particle background of the instrument and to enable the mission science goals. It is a 4-pixel silicon microcalorimeter sensed by an Ir/Au TES network. We have developed the CryoAC demonstration model, a prototype aimed to probe the critical technologies of the detector, i.e., the suspended absorber with an active area of 1 cm 2 ; the low energy threshold of 20 keV; and the operation connected to a 50 mK thermal bath with a power dissipation less than 40 nW. Here, we report the test performed on the first CryoAC DM sample (namely, the AC-S10 prototype), showing that it is fully compliant with its requirements.

We are developing the Cryogenic AntiCoincidence detector (CryoAC) of the ATHENA X-IFU spectrometer. It is a TES-based particle detector aimed to reduce the background of the instrument. Here, we present the result obtained with the last CryoAC single-pixel prototype. It is based on a 1 cm 2 silicon absorber sensed by a single 2 mm × 1 mm Ir/Au TES, featuring an on-chip heater for calibration and diagnostic purposes. We have illuminated the sample with 55 Fe (6 keV line) and 241 Am (60 keV line) radioactive sources, thus studying the detector response and the heater calibration accuracy at low energy. Furthermore, we have operated the sample in combination with a past-generation CryoAC prototype. Here, by analyzing the coincident detections between the two detectors, we have been able to characterize the background spectrum of the laboratory environment and disentangle the primary (i.e. cosmic muons) and secondaries (mostly secondary photons and electrons) signatures in the spectral shape.

The X-ray Integral Field Unit (X-IFU) will operate an array of more than 3000 Transition Edge Sensor pixels at 90 mK with an unprecedented energy resolution of 2.5 eV at 7 keV. In space, primary cosmic rays and secondary particles produced in the instrument structure will continuously deposit energy on the detector wafer and induce fluctuations on the pixels’ thermal bath. We have investigated through simulations of the X-IFU readout chain how these fluctuations eventually influence the energy measurement of X-ray photons. Realistic timelines of thermal bath fluctuations at different positions in the array are generated as a function of a thermal model and the expected distribution of the deposited energy of the charged particles. These are then used to model the TES response to these thermal perturbations and their influence on the onboard energy reconstruction process. Overall, we show that with adequate heatsinking, the main energy resolution degradation effect remains minimal and within the associated resolution allocation of 0.2 eV. We further study how a dedicated triggering algorithm could be put in place to flag the rarer large thermal events.

The ATHENA observatory is the second large class ESA mission to be launched on 2031 at L2 orbit. One of the two onboard instruments is X-IFU, a TES-based kilo-pixel array able to perform simultaneous high-grade energy spectroscopy (FWHM 2.5 eV@7 keV) and imaging over the 5′ field of view. The X-IFU sensitivity is degraded by primary particle background of both solar and galactic cosmic ray (GCR) origins, and by secondary electrons produced by primaries, interacting with the materials surrounding the detector: These particles cannot be distinguished by the scientific photons, thus degrading the instrument performance. Results from studies regarding the GCR component performed by Geant4 simulations address the necessity to use background reduction techniques to enable the study of several key science topics. This is feasible by combining an active Cryogenic AntiCoincidence detector (CryoAC) and a passive electron shielding to reach the required residual particle background of 0.005 cts/cm 2 /s/keV inside the 2–10 keV scientific energy band. The CryoAC is a four-pixel detector made of Si-suspended absorbers sensed by a network of IrAu TESes and placed at a distance < 1 mm below the TES array. Here we will provide an overview of the CryoAC program, starting with some details on the background assessment having impacts on the CryoAC design; then, we continue with its design concept including electronics and the Demonstration Model results, to conclude with programmatic aspects.

The current projects of future X-rays space telescopes foresee high resolving power transition edge sensor (TES) micro-calorimeters arrays as focal plane instrument. In order to full exploit their sensitivity in the space environment, they need an anticoincidence detector to reject the background due to cosmic charged particles. High-energy protons (> 150 MeV) and other charged particle may release in the X-ray calorimeter, the same energy of the X-rays sources under observation. We report the description of the last prototype based on TES calorimeter where a 1-cm 2 silicon chip is used as both substrate and absorber. The readout is made of 96 iridium/gold TESs uniformly distributed on its surface and parallel wired. In this paper, we will describe the design, with the preliminary phonon dynamics simulation, the fabrication, of first demonstration model for the ATHENA space telescope project.

ATHENA is the L2 mission selected by ESA to pursue the science theme “Hot and Energetic Universe.” One of the two focal plane instruments is the X-ray Integral Field Unit, an array of TES microcalorimeters operated at T < 100 mK. To allow the X-ray photons focused by the telescope to reach the detector, windows have to be opened on the cryostat thermal shields. X-ray transparent filters need to be mounted on these open windows to attenuate the IR radiation from warm surfaces, to attenuate RF electromagnetic interferences on TES sensors and SQUID electronics, and to protect the detector from contamination. This paper reviews the ongoing activities driving the design of the X-IFU thermal filters.

We present the design and implementation of a thermal model, developed in COMSOL, aiming to probe the wafer-scale thermal response arising from realistic rates and energies of cosmic rays at L2 impacting the detector wafer of Athena X-IFU. The wafer thermal model is a four-layer 2D model, where two layers represent the constituent materials (Si bulk and Si 3 N 4 membrane) and two layers represent the Au metallization layer’s phonon and electron temperatures. We base the simulation geometry on the current specifications for the X-IFU detector wafer and simulate cosmic ray impacts using a simple power injection into the Si bulk. We measure the temperature at the point of the instrument’s most central TES detector. By probing the response of the system and pulse characteristics as a function of the thermal input energy and location, we reconstruct cosmic ray pulses in Python. By utilizing this code, along with the results of the GEANT4 simulations produced for X-IFU, we produce realistic time-ordered data (TOD) of the temperature seen by the central TES, which we use to simulate the degradation of the energy resolution of the instrument in space-like conditions on this wafer. We find a degradation to the energy resolution of 7 keV X-rays of ≈ 0.04 eV. By modifying wafer parameters and comparing the simulated TOD, this study is a valuable tool for probing design changes on the thermal background seen by the detectors.