Explore the vast range of titles available.

The data on the use of a one- or two-screw technique (1S, 2S) for ventral osteosynthesis of type II dens fractures are contradictory. The aim was to design an apparatus to mimic the physiological conditions and test stability with 1S, 2S, and a headless compression screw (HCS) for osteosynthesis of artificially created type II odontoid fractures. The apparatus was mounted on a Zwick materials testing machine. A total of 18 C1–2 specimens were stratified into three groups (1S, 2S, HCS). Odontoid fractures were artificially created, and osteosynthesis was performed. Each specimen was tested at loads increasing from 1 to 40 N. Screw loosening was observed visually, by fatigue data, and by a camera tracking system. Analysis of the Zwick data and the camera data revealed a significant higher stability after 2S compared to 1S and HCS treatment (Zwick data: p = 0.021, camera data: p < 0.001), while visible screw loosening showed a superiority of the 2S only over HCS (p = 0.038). The developed apparatus allowed the dynamic study of the atlantoaxial joint with a high approximation to physiological conditions. The results demonstrated superiority of the 2S over the 1S and HCS in biomechanical stability in the treatment of type II odontoid fractures.

Objective Closed reduction and dynamic hip screw (DHS) osteosynthesis are preferred as joint‐preserving therapy in case of medial femoral neck fractures (MFNFs). A change in the femoral offset (CFO) can cause gait abnormality, impingement, or greater trochanteric pain syndrome. It is unknown whether the femoral offset (FO) can be postoperatively fully restored. The aim of the study was to investigate the extent of a possible CFO in hip joints after DHS osteosynthesis in the case of an MFNF. Methods In this retrospective study, 104 patients (mean age: 71.02 years, men: n = 50, women: n = 54) with MFNF who underwent closed reduction and DHS osteosynthesis were analyzed by postoperative x‐rays to assess CFO between the operated (OS) and nonoperated joint side (NOS). The studies covered the time period 2010–2020. A statistical comparison was performed between the mean values of FO between OS and NOS, taking into account patient age, gender, and fracture severity. Results All operated hip joints showed a CFO. In 76.0% (79 of 104), the FO decreased (FOD), and in 24.0% (25 of 104), the FO increased (FOI). A critical CFO (>15% CFO) was detected in 52.9% (55 of 104). In hip joints with postoperative FOD, the mean FO between NOS (49.15 mm [±6.56]) and OS (39.32 mm [±7.87]) and in hip joints with postoperative FOI the mean FO between NOS (41.59 [±8.21]) and OS (47.27 [±6.68]) differed significantly (p < 0.001). Preoperative FO (r S: −0.41; p > 0.001) and caput–collum–diaphyseal angle (CCD; r S: 0.34; p > 0.001) correlated with postoperative CFO. FOD was found in hip joints with a preoperative FO >44 mm and CCD <134° vice versa FOI in hip joints with a preoperative FO <44 mm and CCD >134°. Conclusion Closed reduction and DHS osteosynthesis in patients with MFNF result in a clustered significant CFO. The individual FO should be taken into account pre‐ and intraoperatively to avoid a postoperative extensive CFO. One hundred and four patients with medial femoral neck fractures were retrospectively analyzed with regard to postoperative changes of the femoral offset (FO). Seventy‐five percent of the collective showed a decrease of FO and 25% an increase. Fifty‐three percent showed a critical change in FO (>15% referenced to the FO of the contralateral hip). Therefore, exact pre‐operative planning, considering the contralateral healthy hip joint, is mandatory to restore the individual FO of the femoral neck in the best possible manner.

Background Fragility fractures without significant trauma of the pelvic ring in older patients were often treated conservatively. An alternative treatment is surgery involving percutaneous screw fixation to stabilize the posterior pelvic ring. This surgical treatment enables patients to be mobilized quickly and complications associated with bedrest and temporary immobility are reduced. However, the functional outcome following surgery and quality of life of the patients have not yet been investigated. Here, we present a comprehensive study addressing the long-term well-being and the quality of life of patients with fragility pelvic ring fractures after surgical treatment. Methods Between 2011–2019, 215 geriatric patients with pelvic ring fractures were surgically treated at the university hospital in Göttingen (Germany). Of these, 94 patients had fragility fractures for which complete sets of computer tomography (CT) and radiological images were available. Fractures were classified according to Tile and according to the FFP classification of Rommens and Hofmann. The functional outcome of surgical treatment was evaluated using the Majeed pelvic score and the Short Form Health Survey-36 (SF-36). Results Thirty five tile type C and 48 type B classified patients were included in the study. After surgery eighty-three patients scored in average 85.92 points (± 23.39) of a maximum of 100 points using the Majeed score questionnaire and a mean of 1.60 points on the numerical rating scale ranging between 0 and 10 points where 0 points refers to “no pain” and 10 means “strongest pain”. Also, the SF-36 survey shows that surgical treatment positively effects patients with respect to their general health status and by restoring vitality, reducing bodily pain and an increase of their general mental health. Conclusions Patients who received a percutaneous screw fixation of fragility fractures of the posterior pelvic ring reported an overall positive outcome concerning their long-term well-being. In particular, older patients appear to benefit from surgical treatment. Trial registration Functional outcome and quality of life after surgical treatment of fragility fractures of the posterior pelvic ring, DRKS00024768. Registered 8th March 2021 - Retrospectively registered. Trial registration number DRKS00024768 .

PurposeReduction and percutaneous screw fixation of sacroiliac joint disruptions and sacral fractures are surgical procedures for stabilizing the posterior pelvic ring. It is unknown, however, whether smaller irregularities or the inability to achieve an anatomic reduction of the joint and the posterior pelvic ring affects the functional outcome. Here, the long-term well-being of patients with and without anatomic reduction of the posterior pelvis after sacroiliac joint disruptions is described.MethodsBetween 2011 and 2017, 155 patients with pelvic injuries underwent surgical treatment. Of these, 39 patients with sacroiliac joint disruption were examined by radiological images and computer tomography (CT) diagnostics and classified according to Tile. The functional outcome of the different surgical treatments was assessed using the short form health survey-36 (SF-36) and the Majeed pelvic score.ResultsComplete data sets were available for 31 patients, including 14 Tile type C and 17 type B injuries. Of those, 26 patients received an anatomic reduction, 5 patients obtained a shift up to 10 mm (range 5–10 mm). The SF-36 survey showed that the anatomic reduction was significantly better in restoring the patient’s well being (vitality, bodily pain, general mental health and emotional well-being). Patients without this treatment reported a decrease in their general health status.ConclusionsAnatomic reduction was achieved in over 80% of patients in this study. When comparing the long-term well-being of patients with and without anatomic reduction of the posterior pelvis after sacroiliac joint disruptions, the results suggest that anatomical restoration of the joint is beneficial for the patients.

Background Due to the difference in size between the humeral head and the glenoid, the shoulder joint is prone to instability. Therefore, the reconstruction of the physiological joint morphology is of great importance in shoulder joint preservation and replacement surgery. The aim of this study was to describe physiological reference parameters for the morphology of the glenoid for the first time. Material and methods MRI images of the shoulder joints of 418 patients (mean age: 50.6 years [± 16.3]) were retrospectively analysed in a low-grade osteoarthritic population. The glenoid distance in coronal (GDc) and axial view (GDa), glenoid inclination (GI) and version (GV) as well as scapula neck length (SNL) were measured. Parameters were studied in association for age, gender, side and degeneration grade. Results Mean GDc was 33.4 mm (± 3.6), mean GDa 26.8 mm (± 3.2), mean GI 10.5° (± 6.4), mean GV -0.4 mm (± 5.4) and mean SNL was 33.4 mm (± 4.7). GDa was significant higher in right shoulders ( p  < 0.001). GDc and GDa showed significant higher mean values in older patients ( p  < 0.001) and in shoulders with more severe degenerative changes ( p  < 0.05). While GDc, GDa and SNL were significant larger in male patients ( p  < 0.001), GI had a higher mean value in female shoulders ( p  = 0.021). Conclusion Age, gender and shoulder joint degeneration influence changes in the morphological parameters of the glenoid. These findings have to be considered in shoulder diagnostics and surgery. Clinical trial number Not applicable. Highlights 418 shoulder MRIs were retrospectively evaluated for glenoidal distance in coronal and axial view, glenoidal inclination, glenoidal version as well as scapula neck length. Significant side-, age- and gender-specific differences were detected. The analysis of the glenoidal version showed a slight retroversion position on average. The glenoidal distance parameters appear to increase as part of the ageing process due to degenerative changes. These results should be considered in shoulder diagnostics and surgery.

Study design In vitro human cadaveric biomechanical analysis. Objectives Optimization of prostheses for cervical disc arthroplasties (CDA) reduces the risk of complications. The instantaneous helical axis (IHA) is a superior parameter for examining the kinematics of functional spinal units. There is no comprehensive study about the IHA after CDA considering all 3 motion dimensions. Methods Ten human functional spinal units C4-5 (83.2 ± 7.9 yrs.) were examined with an established measuring apparatus in intact conditions (IC), and after CDA, with 2 different types of prostheses during axial rotation, lateral bending, and flexion/extension. Eccentric preloads simulated strains. The IHA orientation and its position at the point of rest (IHA0-position) were analyzed. Results The results confirmed the existing data for IHA in IC. Lateral preloads showed structural alterations of kinematics after CDA: During axial rotation and lateral bending, the shift of the IHA0-position was corresponding with the lateral preloads’ applied site in IC, while after CDAs, it was vice versa. During lateral bending, the lateral IHA orientation was inclined, corresponding with the lateral preloads’ applied site in the IC and oppositely after the CDAs. During flexion/extension, the lateral IHA orientation was nearly vertical in the IC, while after CDA, it inclined, corresponding with the lateral preloads’ applied site. The axial IHA orientation rotated to the lateral preloads’ corresponding site in the IC; after CDA, it was vice versa. Conclusion Both CDAs failed to maintain physiological IHA characteristics under lateral preloads, revealing a new aspect for improving prostheses’ design and optimizing their kinematics.

Background: Osteoporosis causes an increased fracture risk. Clinically, osteoporosis is diagnosed late, usually after the first fracture occurs. This emphasizes the need for an early diagnosis of osteoporosis. However, computed tomography (CT) as routinely used for polytrauma scans cannot be used in the form of quantitative computed tomography (QCT) diagnosis because QCT can only be applied natively, i.e., without any contrast agent application. Here, we tested whether and how contrast agent application could be used for bone densitometry measurements. Methods: Bone mineral density (BMD) was determined by QCT in the spine region of patients with and without the contrast agent Imeron 350. Corresponding scans were performed in the hip region to evaluate possible location-specific differences. Results: Measurements with and without contrast agent administration between spine and hip bones indicate that the corresponding BMD values were reproducibly different between spine and hips, indicating that Imeron 350 application has a location-specific effect. We determined location-specific conversion factors that allow us then to determine the BMD values relevant for osteoporosis diagnosis. Conclusions: Results show that contrast administration cannot be used directly for CT diagnostics because the agent significantly alters BMD values. However, location-specific conversion factors can be established, which are likely to depend on additional parameters such as the weight and corresponding BMI of the patient.

Background: Pelvis fractures are commonly stabilized by surgical implants to facilitate their healing. However, such implants immobilize the iliosacral joint for up to a year until removal. We report how iliosacral joint immobilization affects the walking of patients. Methods: The gaits of patients with immobilized sacroiliac joints after unstable pelvic fracture (n = 8; mean age: 45.63 ± 23.19; five females and three males) and sex- and age-matched healthy control individuals (n = 8; mean age: 46.50 ± 22.91; five females and three males) were recorded and analyzed using a motion capture system. The forces between the tread and feet were also recorded. Standard gait parameters as well as dynamic patterns of joint angles and moments of the lower extremities were analyzed using the simulation software OpenSim. Results: With the exception of hip extensor strength, the monitored joint parameters of the patients showed task-dependent deviations during walking, i.e., plantarflexor force was increased when stepping on an elevated surface, as were hip flexion and extensor moments, knee flexion and extensor moments, as well as ankle dorsiflexion and the associated negative plantarflexor force during stance on the elevated surface. Conclusions: Iliosacral joint fixation causes reduced forward and upward propulsion and requires an extended range of hip motion in the sagittal plane. Patients show significant mobility limitation after iliosacral screw fixation.

Background: The tibial slope (TS) defines the posterior inclination of the tibial plateau (TP). The “individual physiological” TS plays a crucial role in knee-joint stability and should be taken into account in knee-joint surgery. The aim of this study was to analyse the specific morphology of the TS for the medial (med) and lateral (lat) TP in relation to patient characteristics and the measurement method. Methods: In this retrospective study, MRI images of knee joints from 720 patients (mean age: 49.9 years [±17.14]) were analysed. The TS was assessed using two established methods according to Hudek (TSH) and Karimi (TSK) for the med and lat TP and gender/side specificity was analysed. Results: TSH for the med and lat TP showed significantly (p < 0.001) different values compared to TSK (TSKmed: 2.6° (±3.7), TSHmed: 4.8° (±3.5); TSKlat: 3.0° (±4.0), TSHlat: 5.2° (±3.9)). The angles of the lat TP were significantly higher than those of the med TP (TSK: p < 0.001; TSH: p = 0.002). Females showed a higher med and lat TS compared to males (p < 0.001). Conclusions: The measurement method has an influence on the values of the TS in knee-joint MRIs. The TS is significantly different for the med and lat TP regardless of the measurement method. There are gender-specific differences for the TS.

Background: In the age of individualised arthroplasty, the question arises whether currently available standard implants adequately consider femoral condylar morphology (FCM). Therefore, physiological reference values of FCM are needed. The aim was to establish physiological reference values for anterior (ACO) and posterior condylar offset (PCO) as well as for the length of the medial (LMC) and lateral femoral condyles (LLC). Methods: The knee joints of 517 patients (mean age: 52.3 years (±16.8)) were analysed retrospectively using MRI images. Medial (med) and lateral (lat) ACO and PCO, as well as LMC and LLC, were measured. All FCM parameters were examined for association with age, gender, side and osteoarthritis. Results: Mean ACOmed was 2.8 mm (±2.5), mean ACOlat was 6.7 mm (±2.3), mean PCOmed was 25.7 mm (±4.6), mean PCOlat was 23.6 mm (±3.0), mean LMC was 63.7 mm (±5.0) and mean LLC was 64.4 mm (±5.0). Except for PCOmed, the mean values of all other FCM parameters were significantly higher in male knees compared to female knees. ACOmed and PCOmed showed significant side-specific differences. There were no significant differences in relation to age and osteoarthritis. Conclusion: The study showed significant differences in FCM side- and gender-specifically in adult knees. These aspects should be considered in the discussion of individual and gender-specific knee joint replacement.