Explore the vast range of titles available.

Garnet based solid-state batteries have the advantages of wide electrochemical window and good chemical stability. However, at Li-garnet interface, the poor interfacial wettability due to Li 2 CO 3 passivation usually causes large resistance and unstable contact. Here, a Li 2 CO 3 -affiliative mechanism is proposed for air-accessible interface engineering of garnet electrolyte via facile liquid metal (LM) painting. The natural LM oxide skin enables a superior wettability of LM interlayer towards ceramic electrolyte and Li anode. Therein the removal of Li 2 CO 3 passivation network is not necessary, in view of its delamination and fragmentation by LM penetration. This dissipation effect allows the lithiated LM nanodomains to serve as alternative Li-ion flux carriers at Li-garnet interface. This mechanism leads to an interfacial resistance as small as 5 Ω cm 2 even after exposing garnet in air for several days. The ultrastable Li plating and stripping across LM painted garnet can last for 9930 h with a small overpotential. At Li-garnet interface, the poor interfacial wettability due to Li 2 CO 3 passivation causes large resistance and unstable contact. Here the authors propose a Li 2 CO 3 -affiliative mechanism for air-accessible interface engineering of garnet electrolyte with superior wettability via facile liquid metal painting.

When translating photovoltaic technology from laboratory to commercial products, low cost, high power conversion efficiency, and high stability (long lifetime) are the three key metrics to consider in addition to other factors, such as low toxicity, low energy payback time, etc. As one of the most promising photovoltaic materials with high efficiency, today organic–inorganic metal halide perovskites draw tremendous attention from fundamental research, but their practical relevance still remains unclear owing to the notorious short device operation time. In this comment, we discuss the stability issue of perovskite photovoltaics and call for standardized protocols for device characterizations that could possibly match the silicon industrial standards.

Chronic stress refers to the non-specific systemic reaction that occurs when the body is stimulated by various internal and external negative factors over a long time. The physiological response to chronic stress exposure has long been recognized as a potent modulator in the occurrence of atherosclerosis. Furthermore, research has confirmed the correlation between atherosclerosis and cardiovascular events. Chronic stress is pervasive during negative life events and may lead to the formation of plaque. Several epidemiological studies have shown that chronic stress is an independent risk factor for the development of vascular disease and for increased morbidity and mortality in patients with pre-existing coronary artery disease. One possible mechanism for this process is that chronic stress causes endothelial injury, directly activating macrophages, promoting foam cell formation and generating the formation of atherosclerotic plaque. This mechanism involves numerous variables, including inflammation, signal pathways, lipid metabolism and endothelial function. The mechanism of chronic stress in atherosclerosis should be further investigated to provide a theoretical basis for efforts to eliminate the effect of chronic stress on the cardiocerebral vascular system.

In organic solar cells (OSCs), cathode interfacial materials are generally designed with highly polar groups to increase the capability of lowering the work function of cathode. However, the strong polar group could result in a high surface energy and poor physical contact at the active layer surface, posing a challenge for interlayer engineering to address the trade-off between device stability and efficiency. Herein, we report a hydrogen-bonding interfacial material, aliphatic amine-functionalized perylene-diimide (PDINN), which simultaneously down-shifts the work function of the air stable cathodes (silver and copper), and maintains good interfacial contact with the active layer. The OSCs based on PDINN engineered silver-cathode demonstrate a high power conversion efficiency of 17.23% (certified value 16.77% by NREL) and high stability. Our results indicate that PDINN is an effective cathode interfacial material and interlayer engineering via suitable intermolecular interactions is a feasible approach to improve device performance of OSCs. It is desired to design cathode interfacial layers to simultaneously improve the efficiency and stability of organic solar cells and tune the cathode properties. Here, Yao et al. develop such interfacial layers for the best donor-acceptor system and achieve a high certified efficiency close to 17%.

Atrial fibrillation (AF) is a rapid supraventricular arrhythmia. However, the pathogenesis of atrial fibrillation remains controversial. We obtained transcriptome expression profiles GSE41177, GSE115574 and GSE79768 from GEO database. WGCNA was performed, DEGs were screened, PPI network was constructed using STRING database. CTD database was used to identify the reference score of hub genes associated with cardiovascular diseases. Prediction of miRNAs of hub genes was performed by TargetScan. DIANA‐miRPath v3.0 was applied to make functional annotation of miRNA. The animal model of atrial fibrillation was constructed, RT‐PCR was used to verify the expression of hub genes. Immunofluorescence assay for THBS2 and VCAN was made to identify molecular. Design of BP neural network was made to explore the prediction relationship of CXCR4 and TYROBP on AF. The merged datasets contained 104 up‐regulated and 34 down‐regulated genes. GO and KEGG enrichment analysis results of DEGs showed they were mainly enriched in ‘regulation of release of sequestered calcium ion into cytosol’, ‘actin cytoskeleton organization’ and ‘focal adhesion’. The hub genes were CXCR4, SNAI2, S100A4, IGFBP3, CSNK2A1, CHGB, VCAN, APOE, C1QC and TYROBP, which were up‐regulated expression in the AF compared with control tissues. There was strong correlation among the CXCR4, TYROBP and AF based on the BP neural network. Through training, best training performance is 9.6474e‐05 at epoch 14, and the relativity was 0.99998. CXCR4 and TYROBP might be involved in the development of atrial fibrillation by affecting inflammation‐related signalling pathways and may serve as targets for early diagnosis and preventive treatment.

The development of flexible thermistor epidermal electronics (FTEE) to satisfy high temperature resolution without strain induced signal distortion is of great significance but still challenging. Inspired by the nacre microstructure capable of restraining the stress concentration, we exemplify a versatile MXene-based thermistor elastomer sensor (TES) platform that significantly alleviates the strain interference by the biomimetic laminated strategy combining with the in-plane stress dissipation and nacre-mimetic hierarchical architecture, delivering competitive advantages of superior thermosensitivity (−1.32% °C −1 ), outstanding temperature resolution (~0.3 °C), and unparalleled mechanical durability (20000 folding fatigue cycles), together with considerable improvement in strain-tolerant thermosensation over commercial thermocouple in exercise scenario. By a combination of theoretical model simulation, microstructure observation, and superposed signal detection, the authors further reveal the underlying temperature and strain signal decoupling mechanism that substantiate the generality and customizability of the nacre-mimetic strategy, possessing insightful significance of fabricating FTEE for static and dynamic temperature detection. Flexible thermistor epidermal electronics is desired to continuously monitor skin temperature in medical applications. Hao et al. report a nacre mimetic laminated strategy to fabricate thermistors with large mechanical durability for high-fidelity temperature discrimination without signal distortion.

All-polymer solar cells (all-PSCs) based on polymerized small molecular acceptors (PSMAs) have made significant progress recently. Here, we synthesize two A-DA’D-A small molecule acceptor based PSMAs of PS-Se with benzo[c][1,2,5]thiadiazole A’-core and PN-Se with benzotriazole A’-core, for the studies of the effect of molecular structure on the photovoltaic performance of the PSMAs. The two PSMAs possess broad absorption with PN-Se showing more red-shifted absorption than PS-Se and suitable electronic energy levels for the application as polymer acceptors in the all-PSCs with PBDB-T as polymer donor. Cryogenic transmission electron microscopy visualizes the aggregation behavior of the PBDB-T donor and the PSMA in their solutions. In addition, a bicontinuous-interpenetrating network in the PBDB-T:PN-Se blend film with aggregation size of 10~20 nm is clearly observed by the photoinduced force microscopy. The desirable morphology of the PBDB-T:PN-Se active layer leads its all-PSC showing higher power conversion efficiency of 16.16%. Through development of non-fullerene acceptors, OPVs have reached efficiencies of 18%, yet the inadequate operational lifetime still poses a challenge for the commercialisation. Here, the authors investigate the origin of instability of NFA solar cells, and propose some strategies to mitigate this issue.

The cereal endosperm is a major factor determining seed size and shape. However, the molecular mechanisms of endosperm development are not fully understood. Long noncoding RNAs (lncRNAs) function in various biological processes. Here we show a lncRNA, MISSEN , that plays an essential role in early endosperm development in rice ( Oryza sativa ). MISSEN is a parent-of-origin lncRNA expressed in endosperm, and negatively regulates endosperm development, leading to a prominent dent and bulge in the seed. Mechanistically, MISSEN functions through hijacking a helicase family protein (HeFP) to regulate tubulin function during endosperm nucleus division and endosperm cellularization, resulting in abnormal cytoskeletal polymerization. Finally, we revealed that the expression of MISSEN is inhibited by histone H3 lysine 27 trimethylation (H3K27me3) modification after pollination. Therefore, MISSEN is the first lncRNA identified as a regulator in endosperm development, highlighting the potential applications in rice breeding. The cereal endosperm is a major determinant of seed size and shape. Here the authors show that a lncRNA, MISSEN , is expressed from the maternally derived allele in rice seeds and regulates a helicase family protein to support efficient nuclear division, distribution and cellularization in the endosperm.

Tandem organic solar cells are based on the device structure monolithically connecting two solar cells to broaden overall absorption spectrum and utilize the photon energy more efficiently. Herein, we demonstrate a simple strategy of inserting a double bond between the central core and end groups of the small molecule acceptor Y6 to extend its conjugation length and absorption range. As a result, a new narrow bandgap acceptor BTPV-4F was synthesized with an optical bandgap of 1.21 eV. The single-junction devices based on BTPV-4F as acceptor achieved a power conversion efficiency of over 13.4% with a high short-circuit current density of 28.9 mA cm −2 . With adopting BTPV-4F as the rear cell acceptor material, the resulting tandem devices reached a high power conversion efficiency of over 16.4% with good photostability. The results indicate that BTPV-4F is an efficient infrared-absorbing narrow bandgap acceptor and has great potential to be applied into tandem organic solar cells. Development of tandem organic solar cells has been limited by the choice of near-infrared absorbing materials for the rear cell. Here, the authors report a simple strategy to extend the conjugation length of acceptor Y6 and broaden its absorption range to near-infrared region. A tandem organic solar cell with efficiency of 16.4% was achieved.

Two-dimensional materials provide extraordinary opportunities for exploring phenomena arising in atomically thin crystals. Beginning with the first isolation of graphene, mechanical exfoliation has been a key to provide high-quality two-dimensional materials, but despite improvements it is still limited in yield, lateral size and contamination. Here we introduce a contamination-free, one-step and universal Au-assisted mechanical exfoliation method and demonstrate its effectiveness by isolating 40 types of single-crystalline monolayers, including elemental two-dimensional crystals, metal-dichalcogenides, magnets and superconductors. Most of them are of millimeter-size and high-quality, as shown by transfer-free measurements of electron microscopy, photo spectroscopies and electrical transport. Large suspended two-dimensional crystals and heterojunctions were also prepared with high-yield. Enhanced adhesion between the crystals and the substrates enables such efficient exfoliation, for which we identify a gold-assisted exfoliation method that underpins a universal route for producing large-area monolayers and thus supports studies of fundamental properties and potential application of two-dimensional materials. Here, the authors develop a one-step, contamination-free, Au-assisted mechanical exfoliation method for 2D materials, and isolate 40 types of single-crystalline monolayers, including elemental 2D crystals, metal-dichalcogenides, magnets and superconductors with millimetre size.