Explore the vast range of titles available.

Dual fuel combustion has gained attention as a cost-effective solution for reducing the pollutant emissions of internal combustion engines. The typical approach is combining a conventional high-reactivity fossil fuel (diesel fuel) with a sustainable low-reactivity fuel, such as bio-methane, ethanol, or green hydrogen. The last one is particularly interesting, as in theory it produces only water and NOx when it burns. However, integrating hydrogen into stock diesel engines is far from trivial due to a number of theoretical and practical challenges, mainly related to the control of combustion at different loads and speeds. The use of 3D-CFD simulation, supported by experimental data, appears to be the most effective way to address these issues. This study investigates the hydrogen-diesel dual fuel concept implemented with minimum modifications in a light-duty diesel engine (2.8 L, 4-cylinder, direct injection with common rail), considering two operating points representing typical partial and full load conditions for a light commercial vehicle or an industrial engine. The numerical analysis explores the effects of progressively replacing diesel fuel with hydrogen, up to 80% of the total energy input. The goal is to assess how this substitution affects engine performance and combustion characteristics. The results show that a moderate hydrogen substitution improves brake thermal efficiency, while higher substitution rates present quite a severe challenge. To address these issues, the diesel fuel injection strategy is optimized under dual fuel operation. The research findings are promising, but they also indicate that further investigations are needed at high hydrogen substitution rates in order to exploit the potential of the concept.

A significant challenge in utilizing hydrogen in conventional internal combustion engines is achieving a balance between NOx emissions and brake power output. A lean premixed charge (Lambda ≈ 2.5) allows for efficient and stable combustion with minimal NOx emissions. However, this comes at the cost of reduced power density due to the higher air requirements of the thermodynamic process. While supercharging can mitigate this drawback, it introduces increased complexity, cost, and size. An intriguing alternative is the 2-stroke cycle, particularly in an opposed piston (OP) configuration. This study presents the virtual development of a single-cylinder 2-stroke OP engine with a total displacement of 0.95 L, designed to deliver 25 kW at 3000 rpm. Thanks to its compact size, high thermal efficiency, robustness, modularity, and low manufacturing cost, this engine is intended for use either as an industrial power unit or in combination with electric motors in hybrid vehicles. The overarching goal of this project is to demonstrate that internal combustion engines can offer a practical and cost-effective alternative to hydrogen fuel cells without significant penalties in terms of efficiency and pollutant emissions. The design of this novel engine started from scratch, and both 1D and 3D CFD simulations were employed, with particular focus on optimizing the cylinder’s geometry and developing an efficient low-pressure injection system. The numerical methodology was based on state-of-the-art commercial codes, in line with established engineering practices. The numerical results indicated that the optimized engine configuration slightly surpasses the target performance, achieving 29 kW at 3000 rpm, while maintaining near-zero NOx emissions (<20 ppm) and high brake thermal efficiency (~40%) over a wide power range. Additionally, the cost of this engine is projected to be lower than an equivalent 4-stroke engine, due to fewer components (e.g., no cylinder head, poppet valves, or camshafts) and a lighter construction.

Hydraulic manifolds are used to realize compact circuit layout, but may introduce a high pressure drop in the system. Their design is in fact oriented more toward achieving minimum size and weight than to reducing pressure losses. This work studies the pressure losses in hydraulic manifolds using different methods: Computational Fluid Dynamic (CFD) analysis; semi-empirical formulation derived from the scientific literature, when available; and experimental characterization. The purpose is to obtain the pressure losses when the channels’ connections within the manifold are not ascribable to the few classic cases studied in the literature, in particular for 90° bends (elbows) with expansion/contraction and offset intersection of channels. Moreover, since CFD analysis is used to predict pressure losses, general considerations of the manifold design may be outlined and this will help the design process in the optimization of flow passages. The main results obtained show how CFD analysis overestimates the experimental results; nevertheless, the numerical analysis represents the correct trends of the pressure losses.

Rape-seed biodiesel is an interesting option to address the problem of decreasing availability of conventional fossil fuels, as well as to reduce the CO2 emissions of internal combustion engines. The present paper describes an experimental campaign carried out on a current production 4-cylinder, 4-stroke naturally aspirated diesel engine, running on standard diesel fuel and on three different blends of rape-seed biodiesel (20%-50%-100%). Performance, emissions and in-cylinder pressure traces were measured at full load. It was found that the influence of rape-seed biodiesel in the fuel blend is not constant at each operating condition. However, as the biodiesel content increases, full load performance tends to drop, in particular brake specific fuel consumption (maximum worsening: +18%), while soot emission goes down. The maximum improvement observed in terms of soot concentration is 37.5%, at 1200 rpm. The combustion analysis revealed that the main differences among the fuels occur in the first phase of combustion: the burn rate is slower for biodiesel blends at low speeds, and faster at high.

Reactivity Controlled Compression Ignition (RCCI) is one of the most promising solutions among the low temperature combustion concepts, in terms of thermal efficiency and pollutant emissions. However, for values of brake mean effective pressure higher than 10 bar, in-cylinder peak pressure rise rates tend to be too high, limiting the specific power of any 4-Stroke (4S) engine. Such a limitation can be canceled by moving to the 2-Stroke (2S) cycle. Among many alternatives, the “Uniflow” scavenging system with exhaust poppet valves on the cylinder head allows the designer to reproduce the same identical combustion patterns of a 4-stroke RCCI engine, while increasing the indicated power output. The goal of the paper is to explore the potential of a 2-stroke RCCI engine, on the basis of a comprehensive experimental campaign carried out on a modified automotive 2.0 L, 4-stroke, four-cylinder, four-valve diesel engine. The developed prototype can run with one cylinder operating in 4-stroke RCCI mode (gasoline–diesel), while the others work in the standard diesel mode. A One Dimensional-Computational Fluid Dynamics (1D-CFD) model has been built to predict the performance of the same prototype, when operating all four cylinders in RCCI mode. In parallel, an equivalent 2-stroke RCCI virtual engine has been developed, by means of 1D-CFD simulations and empirical assumptions. A numerical comparison between the 4S and the 2S engines is finally presented, in terms of performance and emissions at full load. The study demonstrates that a 2S RCCI engine can maintain all of the advantages of the RCCI combustion, strongly reducing the penalization in terms of performance, in comparison to a standard 4S diesel engine.

The present work aims to assess the influence of the composition of blends of hydrogen (H2) and Natural Gas (NG) on Dual Fuel (DF) combustion characteristics, including gaseous emissions. The 3D-CFD study is carried out by means of a customized version of the KIVA-3V code. An automotive 2.8 L, 4-cylinder turbocharged diesel engine was previously modified in order to operate in DF NG–diesel mode, and tested at the dynamometer bench. After validation against experimental results, the numerical model is applied to perform a set of combustion simulations at 3000 rpm–BMEP = 8 bar, in DF H2/NG-diesel mode. Different H2–NG blends are considered: as the H2 mole fraction varies from 0 vol% to 50 vol%, the fuel energy within the premixed charge is kept constant. The influence of the diesel Start Of Injection (SOI) is also investigated. Simulation results demonstrate that H2 enrichment accelerates the combustion process and promotes its completion, strongly decreasing UHC and CO emissions. Evidently, CO2 specific emissions are also reduced (up to about 20%, at 50 vol% of H2). The main drawbacks of the faster combustion include an increase of in-cylinder peak pressure and pressure rate rise, and of NOx emissions. However, the study demonstrates that the optimization of diesel SOI can eliminate all aforementioned shortcomings.

The numerical study presented in this article is based on an automotive diesel engine (2.8 L, 4-cylinder, turbocharged), considering a NG–H₂ blend with 30 vol% of H₂, ignited by multiple diesel fuel injections. The 3D-CFD investigation aims at improving BTE, CO, and UHC emissions at low load, by means of an optimization of the diesel fuel injection strategy and of the in-cylinder turbulence (swirl ratio, SR). The operating condition is 3000 rpm – BMEP = 2 bar, corresponding to about 25% of the maximum load of a gen-set engine, able to deliver up to 83 kW at 3000 rpm (rated speed). The reference diesel fuel injection strategy, adopted in all the previous numerical and experimental studies, is a three-shot mode. The numerical optimization carried out in this study consisted in finding the optimal number of injections per cycle, as well as the best timing of each injection and the fuel mass split among the injections. The analysis revealed that combustion can be improved by increasing the local concentration of the more reactive fuel (diesel): in detail, the best strategy is a two-shot mode, with SOI1 = −35°CA AFTDC and SOI2 = −20°CA AFTDC, injecting 70% of the total diesel fuel mass at the first shot. As far as the SR is concerned, the best compromise between performance and emissions was found for a relatively low SR = 1.4. The optimization permitted to extract the full potential of the H₂ enrichment in the DF H₂/NG–diesel combustion also at low loads: in comparison to the DF NG case, combustion efficiency, and gross indicated thermal efficiency have been improved by 45.7% and 61.0%, respectively; CO- and UHC-specific emissions have been reduced by about 85.0%. Comparing CDC to the optimized DF 30 vol% H₂/NG–diesel case, soot emissions are completely canceled, CO₂-specific emissions have been reduced by approximately 42.0%, NOₓ-specific emissions by 33.8%. However, further work has to be done in order to reach comparable values of HC and CO, which are still higher than in a standard diesel combustion.

The goal of this study is to develop a clean and efficient thermal unit for a generator set (gen-set) rated at 80 kW, exploring the potential of Dual-Fuel (DF) combustion (Natural Gas-Diesel) on high-speed Compression Ignition (CI) engines. Typically, the most comparable commercial gen-sets are made up of Heavy-Duty (HD) Diesel engines, whose cost and complexity will probably increase to meet more stringent emissions standards. The conversion of a light-duty Diesel engine may permit to match the high efficiency of Diesels with the low emissions of DF combustion at an affordable cost. Moreover, the new thermal unit would be more compact and lighter. Running on Natural Gas (NG) is less expensive than using Diesel fuel, and it offers more opportunities to reduce the environmental impact (e.g., NG can be easily obtained from biomass, in the same site where the gen-set is installed). Last but not the least, in case of interruption of NG supply, the system can be easily switched to conventional Diesel operation, offering a higher fuel flexibility. Despite the large number of scientific publications concerning DF engines, very few of them consider high-speed units equipped with modern Common Rail injection systems. Even more limited are the investigations on the combustion process at medium-high loads (BMEP > 10 bar), carried out by measuring in-cylinder pressure and optimizing all the fundamental control parameters (injection strategy for both Diesel fuel and NG, boost pressure, EGR rates, etc.). It should be observed that the use of state-of-the-art injection systems and the accurate calibration of their parameters at each operating condition is the only way to maximize the benefits of NG in terms of reduction of soot emissions while addressing the well-known issues related to the increase of some pollutants (HC, CO, and NOₓ). This study reviews the results of a theoretical and experimental activity carried out on a four-cylinder, Common Rail, 2.8-liter turbocharged Diesel engine. A gas injection system is installed upstream of the intake plenum, and an open Electronic Control Unit (ECU) is used to calibrate all the most important engine parameters. Thanks to the deep insight into the combustion process provided by in-cylinder pressure analysis and measurement of pollutant emissions, the study presents some general guidelines for setting the control strategy in this type of DF engine. Considering the operating condition at maximum power (BMEP = 12 bar, 3000 rpm, brake power = 83 kW), the following advantages are observed with comparison to the standard Diesel engine: soot is more than halved, NOₓ emissions are reduced by 32% and CO₂ by 31%, and Brake Thermal Efficiency (BTE) increases from 35.8% to 39%. The only drawback is the increase of one order of magnitude of both CO and HC, requiring a specific oxidation catalyst. Another outcome of the study is the limitation on the use of DF NG-Diesel combustion at low loads: the experimental activity demonstrates that it is very difficult to achieve complete combustion of an ultra-lean air-NG premixed charge so that BTE tends to drop. At these conditions, it appears to be more convenient to switch back to standard Diesel operations.

Micro-cogeneration with locally produced biogas from waste is a proven technique for supporting the decarbonization process. However, the strongly variable composition of biogas can make its use in internal combustion engines quite challenging. Dual-fuel engines offer advantages over conventional SI and diesel engines, but there are still issues to be addressed, such as the low-load thermodynamic efficiency and nitrogen oxide emissions. In particular, it is highly desirable to reduce NOx directly in the combustion chamber in order to avoid expensive after-treatment systems. This study analyzed the influence of the combustion system, especially the piston bowl geometry and the injector nozzle, on the performance and emissions of a dual-fuel diesel–biogas engine designed for micro-cogeneration (maximum electric power: 50 kW). In detail, four different cylindrical piston bowls characterized by radii of 23, 28, 33 and 38 mm were compared with a conventional omega-shaped diesel bowl. Moreover, the influence of the injector tip position and the jet tilt angle was analyzed over ranges of 2–10 mm and 30–120°, respectively. The goal of the optimization was to find a configuration that was able to reduce the amount of NOx while maintaining high values of brake thermal efficiency at all the engine operating conditions. For this purpose, a 3D-CFD investigation was carried out by means of a customized version of the KIVA-3V code at both full load (BMEP = 8 bar, 3000 rpm, maximum brake power) and partial load (BMEP = 4 bar, 3000 rpm). The novelty of the study consisted of the parametric approach to the problem and the high number of investigated parameters. The results indicated that the standard design of the piston bowl yielded a near-optimal trade-off at full load between the thermodynamic efficiency and pollutant emissions; however, at a lower load, significant advantages could be found by designing a deeper cylindrical bowl with a smaller radius. In particular, a new bowl characterized by a radius of 23 mm was equivalent to the standard one at BMEP = 8 bar, but it yielded a NOx-specific reduction of 38% at BMEP = 4 bar with the same value of BTE.

The paper describes a numerical study, supported by experiments, on light aircraft 2-Stroke Direct Injected Diesel engines, typically rated up to 110 kW (corresponding to about 150 imperial HP). The engines must be as light as possible and they are to be directly coupled to the propeller, without reduction drive. The ensuing main design constraints are: i) in-cylinder peak pressure as low as possible (typically, no more than 120 bar); ii) maximum rotational speed limited to 2600 rpm. As far as exhaust emissions are concerned, piston aircraft engines remain unregulated but lack of visible smoke is a customer requirement, so that a value of 1 is assumed as maximum Smoke number. For the reasons clarified in the paper, only three cylinder in line engines are investigated. Reference is made to two types of scavenging and combustion systems, designed by the authors with the assistance of state-of-the-art CFD tools and described in detail in a parallel paper. The former is a uniflow system, featuring two exhaust valves per cylinder in the engine head, piston controlled inlet ports and a combustion bowl in the piston; the latter is a loop scavenged design, with both inlet and exhaust ports controlled by the piston, and a non conventional combustion chamber in the engine head (no bowl in the piston). All the calculations presented in the paper are performed by using GT-Power models calibrated by means of CFD-3D calculations (by KIVA-3V) and experiments. The experimental support is provided by two engines: the former is a modern commercial aircraft 2-Stroke Diesel engine, indirect injected, uniflow scavenged; the latter is a research engine based on an old marine unit, featuring loop scavenging and direct injection. The calibration of the GT-Power models is reviewed in the paper.