Explore the vast range of titles available.

As the process complexity has been increased to overcome challenges in plasma etching, individual control of internal plasma parameters for process optimization has attracted attention. This study investigated the individual contribution of internal parameters, the ion energy and flux, on high-aspect ratio SiO2 etching characteristics for various trench widths in a dual-frequency capacitively coupled plasma system with Ar/C4F8 gases. We established an individual control window of ion flux and energy by adjusting dual-frequency power sources and measuring the electron density and self-bias voltage. We separately varied the ion flux and energy with the same ratio from the reference condition and found that the increase in ion energy shows higher etching rate enhancement than that in the ion flux with the same increase ratio in a 200 nm pattern width. Based on a volume-averaged plasma model analysis, the weak contribution of the ion flux results from the increase in heavy radicals, which is inevitably accompanied with the increase in the ion flux and forms a fluorocarbon film, preventing etching. At the 60 nm pattern width, the etching stops at the reference condition and it remains despite increasing ion energy, which implies the surface charging-induced etching stops. The etching, however, slightly increased with the increasing ion flux from the reference condition, revealing the surface charge removal accompanied with conducting fluorocarbon film formation by heavy radicals. In addition, the entrance width of an amorphous carbon layer (ACL) mask enlarges with increasing ion energy, whereas it relatively remains constant with that of ion energy. These findings can be utilized to optimize the SiO2 etching process in high-aspect ratio etching applications.

As low-temperature plasma plays an important role in semiconductor manufacturing, plasma diagnostics have been widely employed to understand changes in plasma according to external control parameters, which has led to the achievement of appropriate plasma conditions normally termed the process window. During plasma etching, shifts in the plasma conditions both within and outside the process window can be observed; in this work, we utilized various plasma diagnostic tools to investigate the causes of these shifts. Cutoff and emissive probes were used to measure the electron density and plasma potential as indicators of the ion density and energy, respectively, that represent the ion energy flux. Quadrupole mass spectrometry was also used to show real-time changes in plasma chemistry during the etching process, which were in good agreement with the etching trend monitored via in situ ellipsometry. The results show that an increase in the ion energy flux and a decrease in the fluorocarbon radical flux alongside an increase in the input power result in the breaking of the process window, findings that are supported by the reported SiO2 etch model. By extending the SiO2 etch model with rigorous diagnostic measurements (or numerous diagnostic methods), more intricate plasma processing conditions can be characterized, which will be beneficial in applications and industries where different input powers and gas flows can make notable differences to the results.

As the importance of ion-assisted surface processing based on low-temperature plasma increases, the monitoring of ion energy impinging into wafer surfaces becomes important. Monitoring methods that are noninvasive, real-time, and comprise ion collision in the sheath have received much research attention. However, in spite of this fact, most research was performed in invasive, not real-time, and collisionless ion sheath conditions. In this paper, we develop a noninvasive real-time IED monitoring system based on an ion trajectory simulation where the Monte Carlo collision method and an electrical model are adopted to describe collisions in sheaths. We technically, theoretically, and experimentally investigate the IED measurement with the proposed method, and compared it with the result of IEDs measured via a quadrupole mass spectrometer under various conditions. The comparison results show that there was no major change in the IEDs as radio-frequency power increased or the IED gradually became broad as gas pressure increased, which was in a good agreement with the results of the mass spectrometer.

As the analysis of complicated reaction chemistry in bulk plasma has become more important, especially in plasma processing, quantifying radical density is now in focus. For this work, appearance potential mass spectrometry (APMS) is widely used; however, the original APMS can produce large errors depending on the fitting process, as the fitting range is not exactly defined. In this research, to reduce errors resulting from the fitting process of the original method, a new APMS approach that eliminates the fitting process is suggested. Comparing the neutral densities in He plasma between the conventional method and the new method, along with the real neutral density obtained using the ideal gas equation, confirmed that the proposed quantification approach can provide more accurate results. This research will contribute to improving the precision of plasma diagnosis and help elucidate the plasma etching process.

Recently, the uniformity in the wafer edge area that is normally abandoned in the fabrication process has become important for improving the process yield. The wafer edge structure normally has a difference of height between wafer and electrode, which can result in a sheath bend, distorting important parameters of the etch, such as ionic properties, resulting in nonuniform etching. This problem nowadays is resolved by introducing the supplemented structure called a focus ring on the periphery of the wafer. However, the focus ring is known to be easily eroded by the bombardment of high-energy ions, resulting in etch nonuniformity again, so that the focus ring is a consumable part and must be replaced periodically. Because of this issue, there are many simulation studies being conducted on the correlation between the sheath structural characteristics and materials of focus rings to find the replacement period, but the experimental data and an analysis based on this are not sufficient yet. In this study, in order to experimentally investigate the etching characteristics of the wafer edge area according to the sheath structure of the wafer edge, the etching was performed by increasing the wafer height (thickness) in the wafer edge area. The result shows that the degree of tilt in the etch profile at the wafer edge and the area where the tilt is observed severely are increased with the height difference between the wafer and electrode. This study is expected to provide a database for the characteristics of the etching at the wafer edge and useful information regarding the tolerance of the height difference for untilted etch profile and the replacement period of the etch ring.

This paper presents the observed changes when replacing the widely used CHF3 gas in semiconductor processing with two isomeric gases, C4H2F6-iso and C4H2F6-Z. This study investigates the etching process results of SiO2 and Si3N4 by varying the ratios of CHF3, C4H2F6 gases. The process outcomes were analyzed using ellipsometer and X-ray photoelectron spectroscopy, while plasma radical densities were examined through quadrupole mass spectrometry. The results are compared across five conditions, with substitution gas ratios ranging from 0% to 100%. The process results indicated that the selectivity increased at certain gas ratios. The diagnostic results provided the ratios of various etchants within the plasma. This research advances the development of alternative precursors designed to mitigate the effects of global warming.

Despite over 90 years of study on the emissive probe, a plasma diagnostic tool used to measure plasma potential, its underlying physics has yet to be fully understood. In this study, we investigated the voltages along the hot filament wire and emitting thermal electrons and proved which voltage reflects the plasma potential. Using a circuit model incorporating the floating condition, we found that the lowest potential on the plasma-exposed filament provides a close approximation of the plasma potential. This theoretical result was verified with a comparison of emissive probe measurements and Langmuir probe measurements in inductively coupled plasma. This work provides a significant contribution to the accurate measurement of plasma potential using the emissive probe with the floating potential method.

As low-temperature plasma plays an important role in semiconductor manufacturing, plasma diagnostics have been widely employed to understand changes in plasma according to external control parameters, which has led to the achievement of appropriate plasma conditions normally termed the process window. During plasma etching, shifts in the plasma conditions both within and outside the process window can be observed; in this work, we utilized various plasma diagnostic tools to investigate the causes of these shifts. Cutoff and emissive probes were used to measure the electron density and plasma potential as indicators of the ion density and energy, respectively, that represent the ion energy flux. Quadrupole mass spectrometry was also used to show real-time changes in plasma chemistry during the etching process, which were in good agreement with the etching trend monitored via in situ ellipsometry. The results show that an increase in the ion energy flux and a decrease in the fluorocarbon radical flux alongside an increase in the input power result in the breaking of the process window, findings that are supported by the reported SiO[sub.2] etch model. By extending the SiO[sub.2] etch model with rigorous diagnostic measurements (or numerous diagnostic methods), more intricate plasma processing conditions can be characterized, which will be beneficial in applications and industries where different input powers and gas flows can make notable differences to the results.

This paper proposes the use of environmentally friendly alternatives, C6F6 and C4H2F6, as perfluorocarbon (PFC) and hydrofluorocarbon (HFC) precursors, respectively, for SiO2 plasma etching, instead of conventional precursors C4F8 and CHF3. The study employs scanning electron microscopy for etch profile analysis and quadrupole mass spectrometry for plasma diagnosis. Ion bombardment energy at the etching conditions is determined through self-bias voltage measurements, while densities of radical species are obtained using quadrupole mass spectroscopy. The obtained results compare the etch performance, including etch rate and selectivity, between C4F8 and C6F6, as well as between CHF3 and C4H2F6. Furthermore, greenhouse gas (GHG) emissions are evaluated using a million metric ton of carbon dioxide equivalent, indicating significantly lower emissions when replacing conventional precursors with the proposed alternatives. The results suggest that a significant GHG emissions reduction can be achieved from the investigated alternatives without a deterioration in SiO2 etching characteristics. This research contributes to the development of alternative precursors for reducing global warming impacts.

The understanding of ion dynamics in plasma applications has received significant attention. In this study, we examined these effects between He and Ar species, focusing on the Ar ion flux on the substrate. To control heterogeneous collisions, we varied the He addition rate at fixed chamber pressure and the chamber pressure at fixed Ar/He ratio in an inductively coupled Ar/He plasma source. Throughout the experiments, we maintained an electron density in the bulk plasma and plasma potential as a constant value by adjusting the RF power and applying an additional DC bias to eliminate any disturbances caused by the plasma. Our findings revealed that the addition of He enhances the Ar ion flux, despite a decrease in the Ar ion density at the plasma–sheath boundary due to the presence of He ions. Moreover, we found that this enhancement becomes more prominent with increasing pressure at a fixed He addition rate. These results suggest that the heterogeneous charge transfer collision between Ar atoms and He ions in the sheath region creates additional Ar ions, ultimately leading to an increased Ar ion flux on the substrate. This finding highlights the potential of utilizing heterogeneous charge transfer collisions to enhance ion flux in plasma processing, without the employment of additional equipment.