Explore the vast range of titles available.

The aim of the study was to analyze the chemical–physical properties and bioactivity (apatite-forming ability) of three recently introduced premixed bioceramic root canal sealers containing varied amounts of different calcium silicates (CaSi): a dicalcium and tricalcium silicate (1–10% and 20–30%)-containing sealer with zirconium dioxide and tricalcium aluminate (CERASEAL); a tricalcium silicate (5–15%)-containing sealer with zirconium dioxide, dimethyl sulfoxide and lithium carbonate (AH PLUS BIOCERAMIC) and a dicalcium and tricalcium silicate (10% and 25%)-containing sealer with calcium aluminate, tricalcium aluminate and tantalite (NEOSEALER FLO). An epoxy resin-based sealer (AH PLUS) was used as control. The initial and final setting times, radiopacity, flowability, film thickness, open pore volume, water absorption, solubility, calcium release and alkalizing activity were tested. The nucleation of calcium phosphates and/or apatite after 28 days aging in Hanks balanced salt solution (HBSS) was evaluated by ESEM-EDX, vibrational IR and micro-Raman spectroscopy. The analyses showed for NeoSealer Flo and AH Plus the longest final setting times (1344 ± 60 and 1300 ± 60 min, respectively), while shorter times for AH Plus Bioceramic and Ceraseal (660 ± 60 and 720 ± 60 min, respectively). Radiopacity, flowability and film thickness complied with ISO 6876/12 for all tested materials. A significantly higher open pore volume was observed for NeoSealer Flo, AH Plus Bioceramic and Ceraseal when compared to AH Plus (p < 0.05), significantly higher values were observed for NeoSealer Flo and AH Plus Bioceramic (p < 0.05). Ceraseal and AH Plus revealed the lowest solubility. All CaSi-containing sealers released calcium and alkalized the soaking water. After 28 days immersion in HBSS, ESEM-EDX analyses revealed the formation of a mineral layer that covered the surface of all bioceramic sealers, with a lower detection of radiopacifiers (Zirconium for Ceraseal and AH Plus Bioceramic, Tantalum for NeoSealer Flo) and an increase in calcium, phosphorous and carbon. The calcium phosphate (CaP) layer was more evident on NeoSealer Flo and AH Plus Bioceramic. IR and micro-Raman revealed the formation of calcium carbonate on the surface of all set materials. A thin layer of a CaP phase was detected only on AH Plus Bioceramic and NeoSealer Flo. Ceraseal did not show CaP deposit despite its highest calcium release among all the tested CaSi-containing sealers. In conclusion, CaSi-containing sealers met the required chemical and physical standards and released biologically relevant ions. Slight/limited apatite nucleation was observed in relation to the high carbonation processes.

Dental professionals often perform physically and mentally demanding therapeutical procedures. They work maintaining muscular imbalance and asymmetrical positions for a long time. The aim of the study was to describe the prevalence and the factors associated to work-related musculoskeletal disorders (WMSD) among Italian dental professionals and the most affected body regions. A cross-sectional observational study was conducted between March 2019 and February 2020. The Nordic Musculoskeletal questionnaire (NMQ) was implemented with questions related to working habits (dental occupation, working hours per week and per days, years of work) and lifestyle (practiced physical activity, including frequency and duration, mobilization activities, and knowledge of ergonomic guidelines) was used. The-chi square test was carried out to detect any statistically significant difference (p < 0.05). Logistic regression was carried out to detect the most significant factors associated to WMSD occurrence. A total of 284 questionnaires have been used for the analysis. A high proportion of dental professionals (84.6%) were affected by WMSD in the last 12 months. A higher prevalence was found in females (87%) when compared to males (80%). The prevalence of WMSD was correlated to the working hours/day and hour/week, with a higher risk for operators working >5 h/day and >30 h/week. In addition, a high prevalence was found in operators working for 2–5 years after graduation. Most of the surveyed dental professionals practiced physical activity (70.1%) but only a few had satisfactorily knowledge of ergonomic guidelines (12.7%). Interestingly, participants who practiced yoga or stretching as physical activities demonstrated lower WMSD (77%) when compared to other physical activities (84%). We can highlight that generic physical activities have no functional effect on WMSD for dental professionals. The most affected body areas were neck (59.9%), shoulders (43.3%), lumbar region (52.1%), dorsal region (37.7%) and wrists (30.6%). Considering the magnitude of the problem, there is an urgent need to implement the education in ergonomics among dental professionals, that may be achieved by teaching biomechanics, posturology and integrative functional therapies (such as yoga) during the university education and by promoting holistic health of dental operators.

Extensive literature reports an increase in physical disorders (pain, pathologies, dysfunctions) and mental malaise/uneasiness (stress, burnout) affecting dental professionals in relation to fast and pressing rhythms of work, long working hours, increasingly demanding patients, ever-evolving technologies, etc. This project has been conceived to bring the science of yoga around the world to dental professionals as a preventive (occupational) medicine and to provide knowledge and means for self-care. Yoga is a concentrative self-discipline of the mind, senses, and physical body, that requires regular daily exercise (or meditation), attention, intention, and disciplined action. M&M: The study aimed to design a Yoga protocol specifically devised for dental professionals (dentists, dental hygienists, and dental assistants) including positions (āsana) to be practiced/used in the dental office. The protocol is targeted for the upper body, namely neck, upper back, chest, shoulder girdle, and wrists, being areas greatly affected by work-related musculoskeletal disorders. This paper represents a yoga-based guideline for the self-cure of musculoskeletal disorders among dental professionals. Results: The protocol includes both sitting (Upavistha position) and standing (Utthana or Sama position) āsana, with twisting (Parivrtta), side bending (Parsva), flexion and forward bending (Pashima), and extension and arching (Purva) āsana to mobilize and decompress, and to provide nourishment and oxygen to the musculo-articular system. The paper delivers different concepts and theories developed and deepened by the authors and introduces and spreads yoga as a medical science among dental professionals for the prevention and treatment of work-related musculoskeletal disorders. We articulate notions ranging from stretching out using the vinyāsa method (breath-driven movement) and inward-focused attention to contemplative/concentrative science, interoceptive attention, self-awareness, the mind–body connection, and receptive attitude. The theory of “muscles are bone ties” is coined and delivered with regard to tensegrity musculoskeletal fascial structures connecting, pulling together, and nearing the bone segments where they are anchored. The paper describes over 60 āsana envisaged to be performed on dental stools or using the walls of a dental office or a dental unit chair. A detailed guideline on the work-related disorders that can find relief with the protocol is provided, including the description of breath control for the practice of āsana in vinyāsa. The foundations of the technique reside in the Iyengar Yoga method and Parināma Yoga method. Conclusions: This paper represents a guideline for self-cure in the prevention or treatment of musculoskeletal disorders affecting dental professionals. Yoga is a powerful concentrative self-discipline able to provide physical and mental well-being, representing great help and support in daily life and business for dental professionals. Yógāsana restores retracted and stiff muscles, giving relief to the strained and tired limbs of dental professionals. Yoga is not intended for flexible or physically performing persons but for people who decide to take care of themselves. The practice of specific āsana represents a powerful tool for the prevention or treatment of MSDs related to poor posture, forward head, chronic neck tension (and related headache), depressed chest, compressive disorders on wrists and shoulders as carpal tunnel, impingement syndromes, outlet syndrome, subacromial pain syndrome and spinal disc pathologies. Yoga, as an integrative science in medicine and public health, represents a powerful tool for the prevention and treatment of occupational musculoskeletal disorders and an extraordinary path for the self-care of dental professionals, sitting job workers, and healthcare providers suffering from occupational biomechanical stresses and awkward postures.

Background: Recently several calcium silicate flowable sealers have been introduced as endodontic materials for the root canal. This clinical study tested the use of a new premixed calcium silicate bioceramic sealer in association with the Thermafil warm carrier-based technique (TF). Epoxy-resin-based sealer with the warm carrier-based technique was the control group. Methodology: Healthy consecutive patients (n = 85) requiring 94 root canal treatments were enrolled in this study and assigned to one filling group (Ceraseal-TF n = 47, AH Plus-TF n = 47) in accordance with operator training and best clinical practice. Periapical X-rays were taken preoperatively, after root canal filling and after 6, 12 and 24 months. Two evaluators blindly assessed the periapical index (PAI) and sealer extrusion in the groups (k = 0.90). Healing rate and survival rate were also evaluated. Chi-square tests was used to analyze significant differences between the groups. Multilevel analysis was performed to evaluate the factors associated with healing status. Results: A total of 89 root canal treatments in 82 patients were analyzed at the end-line (24 months). The total drop-out was 3.6% (3 patients; 5 teeth). A total of 91.1% of healed teeth (PAI 1-2) was observed in Ceraseal-TF, with 88.6% in AH Plus-TF. No significant difference was observed on healing outcome and survival among the two filling groups (p > 0.05). Apical extrusion of the sealers occurred in 17 cases (19.0%). Of these, 6 occurred in Ceraseal-TF (13.3%) and 11 in AH Plus-TF (25.0%). Three Ceraseal extrusions were radiographically undetectable after 24 months. All the AH Plus extrusions did not change during the evaluation time. Conclusions: The combined use of the carrier-based technique and premixed CaSi-based bioceramic sealer showed clinical results comparable with carrier-based technique and epoxy-resin-based sealer. The radiographical disappearance of apically extruded Ceraseal is a possible event in the first 24 months.

The study reviewed the state of the art of the clinical use of a convergent-neck-designed Prama implant. This implant was introduced approximately 10 years ago and was characterized by a specific and unique convergent neck with a microtextured surface (UTM surface) and Zirconium Titanium (ZirTi) implant body surface. The neck design was developed to adopt the biologically oriented preparation technique (BOPT). A critical analysis of the published clinical studies and an evaluation of the adopted clinical protocols were performed. A total of forty-six articles were eligible to be reviewed. Only sixteen clinical studies reported clinical outcomes on Prama implants, and nine of these were selected having the longest follow-up from different research groups. The clinical follow-up/duration of the studies ranged from 12 months to 6 years. The initially proposed protocols explored neck supracrestal–transmucosal placement and gained interest due to its minimally invasive concept and the ability to proceed without a pre-prosthesis second surgery. The following investigations dedicated attention to the subcrestal or equicrestal implant placement with the conventional flap approach. The clinical studies characterized by the transmucosal exposed neck approach reported high survival rates with a stable bone morphology and reduced bone loss during the follow-up. Further recent implementations included the introduction of different convergent neck heights that need to be evaluated. The use of intraoral scanner technologies and digital workflow resulted in a simpler methodology with control of the marginal crown morphology. The studies support the concept that the hard tissue parameters (such as marginal bone level, MBL) and soft tissue parameters (such as pink esthetic score, PES) were stable or improved during the follow-up. Definitive crowns, designed with low invasiveness for soft tissues, were possible thanks to the morphology of the neck. The clinical studies support the use of the Prama implant with the different neck positions, demonstrating hard tissue preservation and optimal esthetic results in the first years following insertion. However, the current body of evidence is not robust enough to draw definitive conclusions, especially in the long term, and further high-quality research (long-term randomized trials) is required to consolidate these early observations.

Dental professionals are exposed to significant unavoidable physical stress, and theoretical ergonomic recommendations for a sitting workplace are inapplicable in many dental activities. Work-related musculoskeletal disorders (WMSDs) represent a serious health problem among dental professionals (prevalence: 64–93%), showing involvement of 34–60% for the low back and 15–25% for the hips. Muscle stress; prolonged sitting; forward bending and twisting of the torso and head; unbalanced working postures with asymmetrical weight on the hips and uneven shoulders; and others are inevitable for dental professionals. Therefore, the approach for the prevention and treatment of WMSDs must be therapeutic and compensatory. This project was conceived to provide a Yoga protocol for dental professionals to prevent or treat WMSDs from a preventive medicine perspective, and it would represent a Yoga-based guideline for the self-cure and prevention of musculoskeletal problems. Methods: Specific Yoga positions (āsana, such as Virāsana, Virabhadrāsana, Garudāsana, Utkatāsana, Trikonāsana, Anuvittāsana, Chakrāsana, Uttanāsana, Pashimottanāsana) have been selected, elaborated on and adapted to be practiced in a dental office using a dental stool or the dental office walls or a dental unit chair. The protocol is specifically devised for dental professionals (dentists, dental hygienists and dental assistants) and targeted for the low back, hips and legs (including knees and ankles). The protocol includes Visranta Karaka Sthiti (supported positions) in sitting (Upavistha Sthiti) and standing (Utthistha Sthiti) positions, twisting/torsions (Parivrtta), flexions/forward bend positions (Pashima) and extensions/arching (Purva) for musculo-articular system decompression and mobilization. Results: Over 60 Yogāsana—specifically ideated for back detensioning and mobilization, lumbar lordosis restoration, trunk side elongation, hip release and leg stretches and decontraction—are shown and described. The paper provides a meticulous description for each position, including the detailed movement, recommendations and mistakes to avoid, and the breathing pattern (breath control) in all the breath-driven movements (āsana in vinyāsa). An exhaustive analysis of posture-related disorders affecting the lower body among dental professionals is reported, including low-back pain, hip pain and disorders, piriformis syndrome and quadratus femoris dysfunction (gluteal pain), iliopsoas syndrome, multifidus disorders, femoroacetabular and ischiofemoral impingement, spinopelvic mobility, lumbopelvic rhythm, impairment syndromes, lower crossed syndrome, leg pain, knee pain and ankle disorders. Conclusions: A detailed guideline of āsana for low-back decompression, hip joint destress, piriformis and gluteal muscle release, lumbar lordosis recovery and a spinopelvic mobility increase has been elaborated on. The designed Yogāsana protocol represents a powerful tool for dental professionals to provide relief to retracted stiff muscles and unbalanced musculoskeletal structures in the lower body.

Background: This pilot prospective study analysed the clinical use of a new bioceramic premixed CaSi-containing sealer in association with a warm carrier-based technique. Methodology: Healthy patients (n = 38) requiring 40 root canal treatments were enrolled. Periapical X-rays were taken preoperatively, after root canal filling and after 1, 6, and 12 months. Two evaluators assessed the Periapical Index (PAI) and the sealer extrusion. The healing rate and survival rate were also evaluated. Barnard test was used to assess the relationship of each potential prognostic factor with periapical index (PAI) at 12-month follow-up. The significance level was set at 0.05. Results: Root canal treatments (n = 38) were analysed at the end-line (12 months). The total drop-out was 5% (two patients; two teeth). A total of 31 teeth (82%) (PAI 1-2) showed complete healing, while 7 (18%) are still healing. Cumulative survival was 100%. Apical extrusion of the sealers was observed in 18 cases (47%). Of these extrusions, nine (50%) resulted radiographically undetectable after 12 months. Conclusions: The study supports the use of premixed CaSi-based bioceramic sealers in association with carrier-based techniques. Periapical extrusion of the sealer and its radiographic modification or disappearance are possible events reported in the first 12 months.

To evaluate the outcome of teeth filled with a single cone technique and a premixed bioceramic sealer at 3 years of follow-up. Healthy patients were consecutively treated by a cohort of postgraduate operators. Root canal filling procedures were performed with NiTi rotary instrumentation, while non-surgical retreatments were performed using NiTi reciprocating instruments. Root canal filling procedures were performed using Ceraseal and the single cone technique. Post-endodontic restorations were performed after 15 days. Provisional and definitive crowns were positioned in case of non-sufficient coronal structure. Periapical radiographs were made before treatment, after filling, and at each follow-up visit (6, 12, 24 and 36 months). The periapical Index (PAI) was used to assess the presence of periapical lesions and their modifications over time. Success (absence of periapical radiolucency, PAI <3) and survival rates were evaluated. The presence of apical extrusion was also radiographically assessed. Linear regression analysis was used to investigate changes in mean PAI scores, and logistic regression analysis was used to investigate changes in the percentage of healed cases. All analyses were replicated using two distinct approaches: per protocol (PP) (treatments who completed the follow-up) and intention to treat (ITT) (all root canal treatments). A significance level of 5% was used for all statistical tests (α=0.05). Fifty-eight endodontic treatments in 52 patients were performed (ITT). Thirty-eight endodontic treatments in 33 patients completed the 3 years of follow-up with a survival rate of 92.7%. The success rate was 85.4% (PP). The use of Ceraseal associated with the single cone technique was safe in maintaining endodontically affected teeth. (EEJ-2024-01-02).

Objectives: To evaluate the retreatment efficacy of premixed bioceramic sealer using a reciprocating system, comparing single-cone and carrier-based obturation techniques. Materials and Methods: Twenty-three monoradicular teeth with oval canals were divided into two groups: NeoSealer Flo with single cone (SC) and NeoSealer Flo with Guttafusion (GF). Retreatment was performed using Reciproc Blue (RB) with a crown-down technique. X-ray and CBCT images were taken to measure the remnant areas and volumes. Results: Apical patency was achieved in all the samples. The remnants were mostly distributed in the middle third in the GF group, while an equal distribution in both the middle and apical thirds was observed in the SC group. The GF group had a lower remnant area and volume after RB 50.05, respectively (0.18 ± 0.33 mm2 vs. 0.39 ± 0.80 mm2 and 0.36 ± 0.59 mm3 vs. 0.51 ± 1.16 mm3). The use of RB 50.05 led to an additional reduction in the remnant areas in the SC (14.89%) and GF (69.49%) groups, while in terms of the volume, the reductions were 20.63% and 36.36%. Conclusions: Reciprocating instruments are effective in removing remnants from root canals filled with both single-cone and carrier-based techniques. The blooming effect in CBCT imaging suggests further in vivo studies for validation.

According to UNEP and FAO reports, the fishing nets abandoned in the seas around the world represent approximately 10% of the plastic waste present in the oceans. These nets, also called ghost nets, can be degraded over time, releasing microplastics and contaminating the environment. Studying the presence and amount of microplastics in an area impacted by ghost nets in the Gulf of Cefalù, northern coast of Sicily, Italy can help to understand the level of contamination in these zones. The planned study methodology has been carried out by sampling sediment and rock substrate, on a quantitative basis, by scuba diving at seven stations selected as the most representative for the presence or absence of fishing nets in the study area. Two different extraction methods for sediment and rock samples were taken from the literature and modified for the present study. Microplastics determination was carried out according to, first, a visual identification and, second, a polymer type identification by ATR-FTIR spectroscopy, demonstrating the presence of polyamide, nylon, or polyethylene in the impacted areas, probably derived from the degradation of fishing nets. The present study reports the first record of microplastics determination in rock substrate samples recollected by scuba diving activities.