Explore the vast range of titles available.

A non-uniform antenna array is proposed to enhance the accuracy of medical microwave imaging systems by increasing the amount of useful information captured about the imaged domain without increasing the number of antennas. These systems have so far been using uniform antenna arrays, which lead to highly correlated signals, limiting the amount of imaging information and adversely affecting diagnostic accuracy. In the proposed non-uniform antenna array method, the optimal number and positions of antennas are calculated with the aim of enhancing spatial diversity and reducing information redundancy. The mutual information coefficient is used as a metric to evaluate and minimize redundancy between received signals. A microwave head imaging system is used to verify the proposed approach. The results of the investigated scenarios show that using a non-uniform antenna configuration outperforms a uniform setup in imaging accuracy and clarity, when using the same number of antennas. Moreover, the reconstructed images demonstrate that using an optimized non-uniform antenna array with fewer elements can outperform a uniform array with more elements in terms of localization accuracy and image quality. The proposed approach improves imaging performance and reduces system complexity, cost, and power consumption, making it a practical solution for real-world biomedical imaging applications.

A bias-free antenna tuning technique that eliminates conventional DC biasing networks is presented. The tuning mechanism is based on a Light-Dependent Resistor (LDR) embedded within the antenna structure. Optical illumination is used to modulate the LDR’s resistance, thereby altering the antenna’s effective electrical length and enabling tuning of its resonant frequency and operating bands. By removing the need for bias lines, RF chokes, blocking capacitors, and control circuitry, the proposed approach minimizes parasitic effects, losses, biasing energy, and routing complexity. This makes it particularly suitable for compact and energy-constrained platforms, such as Internet of Things (IoT) devices. As proof of concept, an LDR is integrated into a ring monopole antenna, achieving tri-band operation in both high and low resistance states. In the high-resistance (OFF) state, the fabricated prototype operates across 2.1–3.1 GHz, 3.5–4 GHz, and 5–7 GHz. In the low-resistance (ON) state, the LDR bridges the two arcs of the monopole, extending the current path and shifting the lowest band to 1.36–2.35 GHz, with only minor changes to the mid and upper bands. The antenna maintains linear polarization across all bands and switching states, with measured gains reaching up to 5.3 dBi. Owing to its compact, bias-free, and low-cost architecture, the proposed design is well-suited for integration into portable wireless devices, low-power IoT nodes, and rapidly deployable communications systems where electrical biasing is impractical.

Wide-angle mechanical beam steering for on-the-move satellite communications is presented in this paper based on a closed-form pillbox antenna system. It includes three main parts: a fixed-feed part, which is a substrate-integrated waveguide (SIW) horn with an extended aperture attached to a parabolic reflector; a novel quasi-optical system, which is a single coupling slot alongside and without spacing from the parabolic reflector; and a radiating disc, which is a leaky-wave metallic pattern. To make the antenna compact, pillbox-based feeding is implemented underneath the metallic patterns. The antenna is designed based on a substrate-guided grounded concept using leaky-wave metallic patterns operating at 20 GHz. Beam scanning is achieved using mechanical rotation of the leaky-wave metallic patterns. The proposed antenna has an overall size of 340 × 335 × 2 mm3, a gain of 23.2 dBi, wide beam scanning range of 120°, from −60° to +60° in the azimuthal plane, and a low side lobe level of −17.8 dB at a maximum scan angle of 60°. The proposed antenna terminal is suitable for next-generation ubiquitous connectivity for households and small businesses in remote areas, ships, unmanned aerial vehicles, and disaster management.

Understanding how electromagnetic (EM) waves travel through different tissues is important for EM medical imaging, sensing, and in-body communication. It is known that EM waves in lossy bio-tissues are nonuniform and do not strictly follow the least time or least loss paths. Instead, they exhibit two distinct wavefronts: the phase wavefront and the amplitude wavefront, which are generally oriented at different angles. The impact of that on imaging and in-body communications is investigated and validated through comprehensive analysis and full-wave EM simulations. Additionally, the impact of a matching medium, commonly used to reduce antenna–skin interface reflections in medical EM applications, on the direction of EM wavefronts, travel time, phase changes, and attenuation is analyzed and quantified. The results show that the Fermat principle of least travel time, often used to estimate EM wave travel time for localization in medical imaging and wireless endoscopy, is only accurate when the loss tangent or dissipation factor of both the matching medium and tissues is very low. Otherwise, the results will be inaccurate, and the dual wavefronts should be considered. The presented analysis and results provide guidance on EM wave travel time and the direction of phase and amplitude wavefronts. This information is valuable for developing reliable processing algorithms for sensing, imaging, and in-body communication.

This paper introduces a novel antenna array synthesis for radar systems based on the concept of a virtual antenna array (VAA) and the method of moments/genetic algorithm (MoM/GA) synthesis method. The VAA concept is applied to both scanning and fixed radiation pattern arrays. The proposed VAA is introduced to simultaneously support the medium-range radar (MRR) and the long-range radar (LRR) with beam width ±7° for LRR and ±37° for MRR. The proposed VAA is distinguished by its minimum number of antenna elements, simple feeding network, high efficiency, and gain, but all of these are at the expense of a large aperture antenna size compared to the planar antenna array (PAA). The VAA has the ability to have the feeding network and the radiating elements on the same layer, as compared to the multilayer PAA. The newly proposed concept is analyzed and verified analytically and experimentally. Two orthogonal (16 elements) VAAs are designed to operate in the frequency range from 23.55 to 24.7 GHz and to support a flat-shoulder shape (FSS) radiation pattern for LRR/MRR. The antenna was fabricated and tested experimentally, and good agreements between the simulated and measured results were noticed. The proposed VAA is introduced to solve the problems of large size, low isolations, low efficiency, feeding network, low resolution, and small coverage range for the antenna arrays of automotive radars. The proposed antenna array is introduced for automotive radar applications at 24 GHz.

Since the CubeSats have become inherently used for the Internet of space things (IoST) applications, the limited spectral band at the ultra-high frequency (UHF) and very high frequency should be efficiently utilized to be sufficient for different applications of CubeSats. Therefore, cognitive radio (CR) has been used as an enabling technology for efficient, dynamic, and flexible spectrum utilization. So, this paper proposes a low-profile antenna for cognitive radio in IoST CubeSat applications at the UHF band. The proposed antenna comprises a circularly polarized wideband (WB) semi-hexagonal slot and two narrowband (NB) frequency reconfigurable loop slots integrated into a single-layer substrate. The semi-hexagonal-shaped slot antenna is excited by two orthogonal +/−45° tapered feed lines and loaded by a capacitor in order to achieve left/right-handed circular polarization in wide bandwidth from 0.57 GHz to 0.95 GHz. In addition, two NB frequency reconfigurable slot loop-based antennas are tuned over a wide frequency band from 0.6 GHz to 1.05 GH. The antenna tuning is achieved based on a varactor diode integrated into the slot loop antenna. The two NB antennas are designed as meander loops to miniaturize the physical length and point in different directions to achieve pattern diversity. The antenna design is fabricated on FR-4 substrate, and measured results have verified the simulated results.

Synthetic microwave focusing methods have been widely adopted in qualitative medical imaging to detect and localize anomalies based on their electromagnetic scattering signatures. This paper discusses the principles, challenges, and limitations of synthetic microwave-focusing techniques in medical applications. It is shown that the various focusing techniques, including time reversal, confocal imaging, and delay-and-sum, are all based on the scalar solution of the electromagnetic scattering problem, assuming the imaged object, i.e., the tissue or object, is linear, reciprocal, and time-invariant. They all aim to generate a qualitative image, revealing any strong scatterer within the imaged domain. The differences among these techniques lie only in the assumptions made to derive the solution and create an image of the relevant tissue or object. To get a fast solution using limited computational resources, those methods assume the tissue is homogeneous and non-dispersive, and thus, a simplified far-field Green’s function is used. Some focusing methods compensate for dispersive effects and attenuation in lossy tissues. Other approaches replace the simplified Green’s function with more representative functions. While these focusing techniques offer benefits like speed and low computational requirements, they face significant ongoing challenges in real-life applications due to their oversimplified linear solutions to the complex problem of non-linear medical microwave imaging. This paper discusses these challenges and potential solutions.

Non-invasive deep brain stimulation using transcranial magnetic stimulation is a promising technique for treating several neurological disorders, such as Alzheimer’s and Parkinson’s diseases. However, the currently used coils do not demonstrate the required stimulation performance in deep regions of the brain, such as the hippocampus, due to the rapid decay of the field inside the head. This study proposes an array that uses the cone coil method for deep stimulation. This study investigates the impact of magnetic core and shielding on field strength, focality, decay rate, and safety. The coil’s size and shape effects on the electric field distribution in deep brain areas are also examined. The finite element method is used to calculate the induced electric field in a realistic human head model. The simulation results indicate that the magnetic core and shielding increase the electric field intensity and enhance focality but do not improve the field decay rate. However, the decay rate can be reduced by increasing the coil size at the expense of focality. By adopting an optimum cone structure, the proposed five-coil array reduces the electric field attenuation rate to reach the stimulation threshold in deep regions while keeping all other regions within safety limits. In vitro and in vivo experimental results using a head phantom and a dead pig’s head validate the simulated results and confirm that the proposed design is a reliable and efficient candidate for non-invasive deep brain magnetic stimulation.

This article presents a solution for the low gain and the poor efficiency of the on‐chip antennas (OCA). The four elements of Quasi‐Yagi‐Uda antennas (QYUA) are introduced based on the diversity technique to reduce the interference between the elements. In addition, these antennas achieve high isolations between them due to the use of reflector for each antenna. The QYUA is selected to improve the radiation properties of the end‐fire radiator in the millimeter‐wave range for on‐chip systems. The proposed MIMO antenna is used for the point to point communications. The complementary metal‐oxide semiconductor with 180 nm standard is used in the antenna design with six metal layers. The QYUA combines three parts (driven element, reflector, and director); the driven consists of two meander lines fed by coplanar‐slot and operates as a dipole, the reflector is an arc likes a semicircle to prevent the back radiation and increase the front to back ratio, and the director is a meander line to directive the radiation into the proposed direction (front end‐fire direction). All MIMO parameters such as envelope correlation coefficient, channel capacity loss, diversity gain, and total active reflection coefficient in addition to the different configurations of the MIMO are presented. All results are verified by computer simulation technology and high‐frequency structure simulator. The contribution of this article is the MIMO antenna design for point to point communications to serve multigiga communications systems with high data rate and high gain. This MIMO system is considered here to solve the problems of OCA designs. The MIMO QYUA is proposed in this paper based on 0.18 μm CMOS technology. The MIMO is introduced to increase the capacity and data rate for short rang communications at 60 GHz. Furthermore, the MOC is introduced to solve the problems of low gain and low efficiency of the on‐chip antenna.

Next-generation communication systems and wearable technologies aim to achieve high data rates, low energy consumption, and massive connections because of the extensive increase in the number of Internet-of-Things (IoT) and wearable devices. These devices will be employed for many services such as cellular, environment monitoring, telemedicine, biomedical, and smart traffic, etc. Therefore, it is challenging for the current communication devices to accommodate such a high number of services. This article summarizes the motivation and potential of the 6G communication system and discusses its key features. Afterward, the current state-of-the-art of 5G antenna technology, which includes existing 5G antennas and arrays and 5G wearable antennas, are summarized. The article also described the useful methods and techniques of exiting antenna design works that could mitigate the challenges and concerns of the emerging 5G and 6G applications. The key features and requirements of the wearable antennas for next-generation technology are also presented at the end of the paper.