Explore the vast range of titles available.

This paper studies the effects of different exhaust gas recirculation (EGR) rates (0%, 5%, 10%, and 15%) on the combustion, performance, and emission characteristics of a biodiesel–diesel (20% biodiesel + 80% diesel) blended fuel engine. This paper mainly analyzes the effects on engine cylinder temperature, cylinder pressure, brake thermal efficiency (BTE), brake-specific fuel consumption (BSFC), NOx emissions, carbon monoxide (CO) emissions, hydrocarbon (HC) emissions, and soot emissions. Firstly, a 3D-CFD model was established by using CONVERGE software, combined with an improved chemical kinetic mechanism including 98 species and 314 reactions, and the accuracy of the simulation model was verified by experimental results. Secondly, the effects of different EGR rates on the combustion, performance, and emission characteristics of biodiesel–diesel blended fuel were studied. The results showed that with the increase in the EGR rate, the cylinder pressure and cylinder temperature in the cylinder decreased. When the EGR rate was 15%, the maximum cylinder temperature decreased by 4.33%. In addition, BSFC increased and BTE decreased. Moreover, with the increase in the EGR rate, NOx decreased significantly, and the higher the EGR rate, the more obvious the reduction in NOx emissions. When the EGR rate was 15%, NOx was reduced by 78.89%. However, with the increase in the EGR rate, the emissions of soot, HC, and CO increased. The optimal EGR rate for the engine is 10%.

With the improvement and development of micro-mechanical manufacturing technology, people can produce an increasing variety of micro-electromechanical systems in recent years, such as micro-satellite thrusters, micro-sensors, micro-aircrafts, micro-medical devices, micro-pumps, and micro-motors. At present, these micro-mechatronic systems are driven by traditional energy power systems, but these traditional energy power systems have such disadvantages as short endurance time, large size, and low energy density. Therefore, efforts were made to study micro-energy dynamical systems with small size, light gravity, high density and energy, and long duration so as to provide continuous and reliable power for these systems. In general, the micro-thermal photoelectric system not only has a simple structure, but also no moving parts. The micro-thermal photoelectric system is a micro-energy power system with good application prospects at present. However, as one of the most important structural components of micro-thermal photoelectric systems, the microburner, is the key to realize the conversion of fuel chemical energy to electric energy in micro-thermal photoelectric system. The studies of how to improve the flame stability and combustion efficiency are very necessary and interesting. Thus, some methods to improve the performance of micro-burners were introduced and summarized systematically, hoping to bring some convenience to researchers in the field.

In this paper, the aerodynamic characteristics of two vehicles and three vehicles in the platoon under different vehicle spacings have been explored in detail. Firstly, the realizable k-ε model was used to verify the numerical method based on a single 35° Ahmed body. Then, the aerodynamic characteristics such as drag characteristics, surface pressure, wake structure, and turbulent kinetic energy distribution were analyzed for the platoon of two and three 35° Ahmed bodies. Although the RANS (Reynolds-averaged Navier–Stokes) model had got good results for simulating a single 35° Ahmed body, when simulating two 35° Ahmed bodies in the platoon, it was found that there is still a big error compared with the experimental data. In the three 35° Ahmed body, the drag coefficient of the leading body is almost unchanged compared with that of the leading body in the two-vehicle platoon, while the drag coefficients of the middle body and the trailing body are both reduced compared with those of the single body. For x/L = 0.25, the middle body is about 56% of the single-body value, and the trailing car is about 88% of the single-body value. It can be seen that the drag reduction effect of three 35° Ahmed bodies is larger than that of two 35° Ahmed bodies. It is shown that the aerodynamic characteristics are very sensitive to the selected platoon vehicle model. Because model with different geometric shapes will produce different wake structures, different aerodynamic phenomena will occur when they are arranged in the platoon.

In order to investigate the distribution characteristics of gas-particle two-phase flow in the diesel particulate filter in the capture process, a mathematical model of gas-particle two-phase flow for inside-and-outside filter had been established in the capture process according to the mass conservation equation, momentum conservation equation, and k-ε turbulence equation. The model verification was carried out with the experimental and simulated of flow distribution characteristics of gas-particle two-phase. The obtained results showed that the static pressure gradient along the radial distribution was greater at the inlet of the filter in capture process in the diesel particulate filter, which could easily lead to causing eventual fatigue damage due to stress concentration in the front-end of filter; moreover, the weaker the vortex strength of gas-particle formed in expansion pipe was, the better uniformity of flow velocity and soot concentration distribution were. Therefore, the established mathematical model can be used for predicting gas-particle flow velocity distribution in the diesel particulate filter.

Diesel particulate filter (DPF) is considered as an effective method to control particulate matter (PM) emissions from diesel engines, which is included in the mandatory installation list by more and more national/regional laws and regulations, such as CHINA VI, Euro VI, and EPA Tier3. Due to the limited capacity of DPF to contain PM, the manufacturer introduced a method of treating deposited PM by oxidation, which is called regeneration. This paper comprehensively summarizes the most advanced regeneration technology, including filter structure, new catalyst formula, accurate soot prediction, safe and reliable regeneration strategy, uncontrolled regeneration and its control methods. In addition, due to the change of working conditions in the regeneration process, the additional emissions during regeneration are discussed in this paper. The DPF is not only the aftertreatment device but also can be combined with diesel oxidation catalyst (DOC), selective catalytic reduction (SCR) and exhaust recirculation (EGR). In addition, the impact of DPF modification on the original system of some old models has been reasonably discussed in order to achieve emission targets.

Due to the increasing air pollution from diesel engines and the shortage of conventional fossil fuels, many experimental and numerical types of research have been carried out and published in the literature over the past few decades to find a new, sustainable, and alternative fuels. Biodiesel is an appropriate alternate solution for diesel engines because it is renewable, non-toxic, and eco-friendly. According to the European Academies Science Advisory Council, biodiesel evolution is broadly classified into four generations. This paper provides a comprehensive review of the production, properties, combustion, performance, and emission characteristics of diesel engines using different generations of biodiesel as an alternative fuel to replace fossil-based diesel and summarizes the primary feedstocks and properties of different generations of biodiesel compared with diesel. The general impression is that the use of different generations of biodiesel decreased 30% CO, 50% HC, and 70% smoke emissions compared with diesel. Engine performance is slightly decreased by an average of 3.13%, 89.56%, and 11.98% for higher density, viscosity, and cetane, respectively, while having a 7.96% lower heating value compared with diesel. A certain ratio of biodiesel as fuel instead of fossil diesel combined with advanced after-treatment technology is the main trend of future diesel engine development.

In this paper, biodiesel was used as an alternative fuel to investigate the combustion and emission characteristics of a four-stroke diesel engine, in terms of cylinder pressure, heat release rate, cylinder temperature, brake thermal efficiency, brake specific fuel consumption, nitrogen oxide, soot, carbon monoxide, and hydrocarbon. Firstly, a diesel engine cylinder model was developed by AVL-Fire software coupled with CHEMKIN code to simulate the injection and combustion of biodiesel with a kinetic mechanism with 106 species and 263 reactions. Then, the simulation model was validated by experimental results under 100% and 50% load conditions and used to simulate the combustion process of a diesel engine fueled with pure diesel, biodiesel, and biodiesel–diesel blends with 10%, 20%, 30% biodiesel by volume, respectively. The results showed that the brake specific fuel consumption increased with the increase of mixed biodiesel ratio. The brake specific fuel consumptions of B10, B20 and B30 increased by 1.1%, 2.3% and 3.3%, respectively, compared with that of D100. The combustion and emission characteristics of the diesel engine are improved. Therefore, biodiesel can be used as an alternative fuel for the diesel engine. The diesel–biodiesel fuel can improve the combustion and emission characteristics of the diesel engine.

In order to study the hydrocarbon combustion in the low-temperature catalytic process of a catalytic gasoline particulate filter (CGPF) during cold start, a mathematical model of the CGPF is established and verified firstly. Then, take T 50 (a temperature when the hydrocarbon conversion rate reaches 50%) as hydrocarbon light-off (LO) temperature; the effects of different exhaust parameters and structural parameters on hydrocarbon light-off performance and reaction rate are investigated based on simulation results. Finally, orthogonal experiment analysis is employed to further obtain the most significant factors and suggested parameter solution. The results show that the hydrocarbon LO performance of the CGPF during cold start is positively correlated with exhaust oxygen concentration, porosity, and filter length, but it is negatively correlated with exhaust flow rate and exhaust water vapor concentration. In addition, the inlet of the channel has a significant HC reaction when the oxygen concentration reaches 2.2%, and porosity mainly influences the front half part of the filter. Moreover, the influence degree relationship of the five factors is oxygen > mass flow > porosity > length > water vapor, and the optimum solution of length, vapor, mass flow, porosity, and oxygen is 150 mm, 12.31%, 0.002 kg/s, 0.55, and 2.2%, respectively. This work offers us great reference value for CGPF performance enhancement and hydrocarbon abatement of a GDI engine. Graphical abstract

In order to pursue clean, low-carbon, safe, and efficient energy utilization and accelerate the development of new energy, sustainability is the necessary research. In recent decades, solar power generation has rapidly formed and been widely applied. Sustainability analysis is a key aspect that directly affects the construction of solar power projects when conducting solar power generation construction. This paper attempts to start with life cycle sustainability assessment (LCSA) and study the status quo of its three pillars (These three pillars include life cycle assessment, life cycle cost assessment, and social life cycle assessment) in the field of solar power generation. At the same time, the externality indicators are considered between pillars. In addition, the application of uncertainty analysis was studied during the analysis process to address the impact of various random factors. The conclusion shows that further research is needed to support this transition by integrating life cycle assessment, life cycle cost, and social life cycle assessment into LCSA for the evaluation. To improve the effectiveness of future research, studies should focus on fulfilling major data gaps in the literature such as the lack of detailed documentation for specific materials and background process choices in life cycle assessment databases. The development of solar power generation can be an important alternative in efforts to decrease climate change impacts and pursue cleaner energy sources in countries where solar energy is more easily available by integrating life cycle assessment (LCA), life cycle cost (LCC), and social life cycle assessment (SLCA) into LCSA. The sustainable development of the solar power generation industry in terms of multiple aspects is supported.

In order to improve the accuracy of numerical simulation, a new heat transfer model is developed by using a modular approach in the Anstalt für Verbrennungskraftmaschinen (AVL)-Boost software. The improved heat transfer model mainly considers the effects of the swirl and boiling heat transfer inside the engine. In addition, a chemical kinetics mechanism including 475 reactions and 134 species is employed to predict the combustion of diesel engines fueled with biodiesel. The result shows that the boiling heat transfer will occur, especially in the high-temperature area. Analysis shows that the improved model is reliable and its precision is increased. Finally, the perturbation method is employed to investigate the relatively important inputs as the complex nonlinear function with a lot of output data and input data produced by the improved model. The relative effects of different parameters such as EGR, injection mass, injection timing, compression ratio, inlet air pressure, fuel injection pressure, exhaust pressure and inlet air temperature on performance and emission characteristics are compared. The eight parameters are investigated on four outputs of brake power, Brake Specific Fuel Consumption (BSFC), NOx and HC. The injected fuel mass plays an important role in emissions and performance. The EGR, compression ratio and inlet air pressure have a great effect on the HC and NOx emission.