Explore the vast range of titles available.

Hydrodynamic boundary layer is a significant phenomenon occurring in a flow through a bluff body, and this includes the flow motion and mass transfer. Thus, it could affect the biofilm formation and the mass transfer of substrates in microbial fuel cells (MFCs). Therefore, understanding the role of hydrodynamic boundary layer thicknesses in MFCs is truly important. In this study, three hydrodynamic boundary layers of thickness 1.6, 4.1, and 5 cm were applied to the recirculation mode membrane-less MFC to investigate the electricity production performance. The results showed that the thin hydrodynamic boundary could enhance the voltage output of MFC due to the strong shear rate effect. Thus, a maximum voltage of 22 mV was obtained in the MFC with a hydrodynamic boundary layer thickness of 1.6 cm, and this voltage output obtained was 11 times higher than that of MFC with 5 cm hydrodynamic boundary layer thickness. Moreover, the charge transfer resistance of anode decreased with decreasing hydrodynamic boundary layer thickness. The charge transfer resistance of MFC with hydrodynamic boundary layer of thickness 1.6 cm was 39 Ω, which was 0.79 times lesser than that of MFC with 5 cm thickness. These observations would be useful for enhancing the performance of recirculation mode MFCs.

A technical, environmental, and economic feasibility study for a patented hybrid renewable energy harvester system for residential application is conducted in this paper. This system can be mounted on top of an existing residential building to provide electricity from renewable sources. The system is characterized by its V-shaped roof guide vane (VRGV) that directs and augments airflow into the wind turbine, to enhance the rotational and power generation performance of the wind turbines in low wind speed areas. Furthermore, the VRGV increases the installation area for the solar photovoltaic panels and expand the rainwater collection area for the building, and facilitates natural ventilation and prevents excessive solar radiation into the room. The environment–economic evaluation of the system is conducted based on the life-cycle cost (LCC) in terms of low carbon and economic cost-effectiveness. The evaluation of the system with dimensions of 15 m (L) × 16 m (W) × 17.05 m (H) showed that the annual energy generated is 21.130 MWh. Annual low-carbon benefit of the system is estimated to be 11.894 t. The cumulative net present value (NPV) of the system in the life cycle time (20 years) is $52,207.247, with the consideration of a discount rate of 8%; also, the cash flow breakeven occurs in the 11th year. It is important to note that the carbon payback period (CPP) of the system is five years.

The technical and economic features of a patented V-shape roof guide vane (VRGV) with a solar and wind power generation system mounted on an eco-roof system are presented in this paper. Moreover, this innovative VRGV was investigated on for the purpose of improving the performance of a vertical axis wind turbine (VAWT), which was installed on an eco-roof system to solve the low-efficiency power generation problem of the wind turbines under the condition of a low wind speed. This paper proposes a preliminary study for the performance of the VAWT with the VRGV on a building. This research used a mock-up building with a double slope roof, where a five straight-bladed VAWT was mounted and tested under two conditions, with and without the VRGV. From the comparative experiments, the self-starting performance and rotational speed of the VAWT mounted above a double slope roof with the VRGV have been significantly improved compared to the VAWT without the VRGV. Further, the power coefficient (Cp) of the VAWT can be augmented to about 71.2% increment due to the VRGV design. In addition, numerical simulations by computational fluid dynamics (CFD) were proposed to verify the augmented effect of the Cp of the VAWT under the influence of the VRGV in the experiment. Besides, economic estimation of the VRGV was conducted.

A flexible proximity sensor fully fabricated by inkjet printing is proposed in this paper. The flexible proximity sensor is composed of a ZnO layer sandwiched in between a flexible aluminum sheet and a web-shaped top electrode layer. The flexible aluminum sheet serves as the bottom electrode. The material of the top electrode layer is nano silver. Both the ZnO and top electrode layers are deposited by inkjet printing. The fully inkjet printing process possesses the advantages of direct patterning and low-cost. It does not require photolithography and etching processes since the pattern is directly printed on the flexible aluminum sheet. The prototype demonstrates that the presented flexible sensor is sensitive to the human body. It may be applied to proximity sensing or thermal eradiation sensing.

Due to the fact that Iron oxide (Fe2O3) is known to have a good effect on the photochemical reaction of catalysts, an investigation in this study into the enhancement of the degradation performance of bio-electro-Fenton microbial fuel cells (Bio-E-Fenton MFCs) was carried out using three photocatalytic cathodes. These cathodes were produced at different calcination temperatures of Fe2O3 ranging from 500 °C to 900 °C for realizing their performance as photo catalysts within the cathodic chamber of an MFC, and they were compared for their ability to degrade oily wastewater. Results show that a suitable temperature for the calcination of iron oxide would have a significantly positive effect on the performance of Bio-E-Fenton MFCs. An optimal calcination temperature of 500 °C for Fe2O3 in the electrode material of the cathode was observed to produce a maximum power density of 52.5 mW/m2 and a chemical oxygen demand (COD) degradation rate of oily wastewater (catholyte) of 99.3% within one hour of operation. These novel findings will be useful for the improvement of the performance and applications of Bio-E-Fenton MFCs and their future applications in the field of wastewater treatment.

Nowadays, increased interest among the scientific community to explore the Calophyllum inophyllum as alternative fuels for diesel engines is observed. This research is about using mixed Calophyllum inophyllum-palm oil biodiesel production and evaluation that biodiesel in a diesel engine. The Calophyllum inophyllum–palm oil methyl ester (CPME) is processed using the following procedure: (1) the crude Calophyllum inophyllum and palm oils are mixed at the same ratio of 50:50 volume %, (2) degumming, (3) acid-catalysed esterification, (4) purification, and (5) alkaline-catalysed transesterification. The results are indeed encouraging and satisfy ASTM D6751. CPME shows the high heating value (37.9 MJ/kg) but low kinematic viscosity (4.50 mm2/s) due to change a higher proportion of shorter-chain and unsaturated FAMEs, which tend to lower viscosity compared to Calophyllum inophyllum methyl ester (CIME).). The blended fuels exhibit higher brake-specific fuel consumption (BSFC) and NOx emissions, along with lower brake thermal efficiency (BTE) and reduced CO and HC emissions compared to diesel fuel across the entire range of speeds. Among the blends, CPME5 offered better performance compared to other blends fuel ratios.

In this study a biophysical passive micromixer with channel anamorphosis in a space of 370 mm, which is shorter than traditional passive micromixers, could be created by mimicing features of vascular flow networks and executed with Reynolds numbers ranging from 1 to 90. Split and recombination (SAR) was the main mixing method for enhancing the convection effect and promoting the mixing performance in the biophysical channel. The 2D numerical results reveal that good mixing efficiency of the mixer was possible, with εmixing = 0.876 at Reynolds number ration Rer = 0.85. Generally speaking, increasing the Reynolds number will enhance the mixing. In addition, the sidewall effect will influence the mixing performance and an optimal mixing performance with εmixing = 0.803 will occur at an aspect ratio of AR = 2. These findings will be useful for enhancing mixing performance for passive micromixers.

Nowadays, solid organic waste is of major environmental concern and is reaching critical levels worldwide. Currently, a form of natural decomposition, known as composting technology, is widely used to deal with organic waste. This method is applied to enhance the performance of solid microbial fuel cells (SMFCs) in this study. Operational composting parameters (carbon/nitrogen ratio, moisture content and pH value) are investigated to explore the optimal power performance of solid microbial fuel cells (SMFCs). Results indicate that the carbon/nitrogen ratio and the moisture content displayed the most significant impact on SMFCs. When the carbon/nitrogen ratio is 31.4 and moisture content is 60%, along with a pH value of 6–8, a better SMFC power performance would be obtained. These findings would provide positive information regarding the application of compost in SMFCs.

Microbial Fuel Cell (MFC) has various application potential as in generation of bioelectricity, bio-hydrogen production, waste water treatment and it is also used as biosensors. It would not be possible to headway without mentioning that MFCs have quite a many similarities with Chemical Fuel Cells (CFC). It is seen that a lot of research is carried out for CFCs as compared to MFCs. Most of the research works on MFCs include experimental approach while very few computational studies have been carried out for MFCs. So an endeavour is made to create a model which mimics the working by simulating the key physical and biochemical processes occurring. Results imply that variation of current density occurs with change in Reynolds number (Re) and kinetic rate of reaction (k) which lead to the study of effects of variation of flow rates, turbulence and the action of different bacteria in the efficiency of MFCs. The current density achieved computationally is around 512 mA/m2 for Re=5 and k=10−3 which is in good agreement with the experimental data. Regions of higher current density are found which can be used to improvise the MFCs. Present mathematical model provides a new perspective in understanding the biomass concentration across the MFC and gives better knowledge of the mechanisms taking place. This simple computational framework provides insight into the fluid dynamics involved during continuous feeding, by overcoming the limitations and technical barriers in monitoring and examining through experiments. By implementing the findings from this model optimization of designs can be achieved leading to higher current generation, increase in efficacy and cost effective production techniques which paves the way for future work.

The journal is publishing this correction to update the name of the Academic Editor listed on this published paper [...]