Explore the vast range of titles available.

Extreme temperatures and fluid pressures are measured, and their causes modelled, in a borehole into the Alpine Fault, where an earthquake rupture is expected within the next few decades. Hydrothermal pressure in earthquake zones Rock deformation at geologic faults is affected by changes in temperature and in the pressure exerted by fluids within the pores of the rocks. Earthquakes occur when variations in these conditions lead to destabilization of mineral phases in Earth's crust, so understanding how this 'tipping point' is reached is important for forecasting earthquakes. Rupert Sutherland et al . report findings from a borehole drilled into the upper part of the Alpine Fault of southern New Zealand. This fault is thought to be late in its cycle of stress accumulation and is therefore expected to rupture in a magnitude 8 earthquake in the coming decades. The authors observed a pore fluid pressure gradient that is well above hydrostatic levels, meaning greater pressure on the surrounding rock, and a high geothermal gradient within the 'hanging wall' of the fault. They conclude that these extreme conditions result from rapid fault movement, which transports rock and heat upwards from deep below the surface, and topographically driven fluid movement that concentrates heat into valleys at the surface. Temperature and fluid pressure conditions control rock deformation and mineralization on geological faults, and hence the distribution of earthquakes 1 . Typical intraplate continental crust has hydrostatic fluid pressure and a near-surface thermal gradient of 31 ± 15 degrees Celsius per kilometre 2 , 3 . At temperatures above 300–450 degrees Celsius, usually found at depths greater than 10–15 kilometres, the intra-crystalline plasticity of quartz and feldspar relieves stress by aseismic creep and earthquakes are infrequent. Hydrothermal conditions control the stability of mineral phases and hence frictional–mechanical processes associated with earthquake rupture cycles, but there are few temperature and fluid pressure data from active plate-bounding faults. Here we report results from a borehole drilled into the upper part of the Alpine Fault, which is late in its cycle of stress accumulation and expected to rupture in a magnitude 8 earthquake in the coming decades 4 , 5 . The borehole (depth 893 metres) revealed a pore fluid pressure gradient exceeding 9 ± 1 per cent above hydrostatic levels and an average geothermal gradient of 125 ± 55 degrees Celsius per kilometre within the hanging wall of the fault. These extreme hydrothermal conditions result from rapid fault movement, which transports rock and heat from depth, and topographically driven fluid movement that concentrates heat into valleys. Shear heating may occur within the fault but is not required to explain our observations. Our data and models show that highly anomalous fluid pressure and temperature gradients in the upper part of the seismogenic zone can be created by positive feedbacks between processes of fault slip, rock fracturing and alteration, and landscape development at plate-bounding faults.

A 3 km deep research borehole KFD1 was drilled in the Koyna reservoir-triggered seismicity region, Western India, between December 2016 and May 2017. The 1967 M 6.3 Koyna earthquake had generated a NNE-SSW trending surface fissure zone in the Nanel-Donichawadi-Kadoli sector. KFD1 is located ~5 km south of Kadoli along the trend of the Donichawadi fault zone. Online gas monitoring was carried out during drilling of KFD1 from 1315 m to 2831 m depth to sample and study the composition of crustal gases. Formation gases CO2, CH4, H2, and He were only observed during water flushing of ~100 m intervals following coring runs. Laboratory analyses of gas samples collected between 1737 m and 2831 m depth revealed concentrations of up to 1200 ppmv CO2, 186 ppmv CH4, 139 ppmv H2, and 12.8 ppmv He. Zones enriched in gases are mostly below the 2100 m depth with significant He enhancement ranging from 4.6 to 7.6 ppmv above the atmospheric value. The He-rich zones correlate well with the zones of anomalous physical and mechanical properties identified from geophysical logs and are characterized by high fracture density as revealed from borehole images, indicating that the borehole punctured multiple fracture zones. The helium concentrations are consistent with those previously observed over the surface fissures near Kadoli, suggesting a southward extension of the Donichawadi fault zone up to the KFD1 site and confirming that the fault zone is permeable even after 50 years of the 1967 Koyna earthquake. 3He/4He ratios of eleven gas samples fall between 0.426±0.022 and 0.912±0.059 Ra, with 4He/20Ne values between 0.3449±0.0091 and 0.751±0.020. Air-corrected helium isotope ratios indicate that helium is a mixture of atmospheric and crustal radiogenic components but no mantle contribution within 2σ analytical uncertainties.

Volatiles transported from the Earth’s interior to the surface through permeable faults provide insights on the gas composition of deep reservoirs, mixing and migration processes, and can also be applied as gas-geothermometer. Here, we present carbon (δ13C), hydrogen (δ2H) and nitrogen (δ15N) isotopic data of CO2, CH4, and N2 from gas samples collected from the Kızıldere and Tekke Hamam geothermal fields, located along the eastern segment of the Büyük Menderes Graben, Turkey. The stable isotopic composition of carbon (δ13C) ranges from +0.30 to +0.99‰ (PDB) for CO2 from Kızıldere and is slightly more variable (−0.95 to +1.3‰) in samples from Tekke Hamam. Carbon isotope data in combination with CO2/3He data reveal that ~97% (Tekke Hamam) to ~99% (Kızıldere) of CO2 derives from limestone sources, with the residual CO2 being magmatic in origin with no evidence for CO2 from organic sources. The slightly higher contribution of limestone-derived CO2 in Kızıldere, compared to Tekke Hamam can be attributed to the higher temperatures of the Kızıldere reservoir and resulting amplified fluid–limestone interaction, as well as helium depletion during phase separation for Kızıldere samples. In contrast to the carbon isotopic composition of CO2, the δ13C values of methane from Kızıldere and Tekke Hamam are clearly distinct and vary between −23.6 and −20.8‰ for Kızıldere and −34.4 and −31.7‰ for Tekke Hamam, respectively. The δ2H-CH4 composition is also distinct, measured as −126.7‰ for Kızıldere and −143.3‰ for Tekke Hamam. CO2-CH4 carbon isotope geothermometry calculations based on the isotopic fractionation of δ13C between the dominant component CO2 and the minor component CH4 reveals temperatures 20–40 °C and 100–160 °C higher than the bottom–hole temperatures measured for Tekke Hamam and Kızıldere, respectively. Based on the CO2-CH4 carbon isotope disequilibrium, unusual high methane concentrations of ~0.3 to 0.4 vol.-% and CH4/3He-δ13C-CH4 relationships we suggest thermal decomposition of late (Tekke Hamam) to over-mature (Kızıldere) organic matter and, to some extent, also abiogenic processes as principal source of methane. The N2/36Ar ratios of most samples reveal the existence of a non–atmospheric nitrogen component within the gas mixture issuing from both fields, in addition to a constant contribution of atmospheric derived nitrogen accompanied into the system via the meteoric recharge of the geothermal system. Based on the δ15N isotopic ratios (varying between −4.44‰ and 4.54‰), the non–atmospheric component seems to be a mixture of both sedimentary (crustal organic) and mantle nitrogen. The thick Pliocene sedimentary sequence covering the metamorphic basement is the likely major source for the thermogenic content of CH4 and crustal N2 gas content in the samples.

The Trans‐Amazon Drilling Project (TADP) drilled a sequence of claystones, siltstones, and sandstones in the Acre sedimentary basin, reaching a final depth of 923 m. This study characterizes the occurrence and compositional variation of light gaseous hydrocarbons detected using the online gas analysis (OLGA) monitoring system deployed during drilling, along with methane (CH 4 ) and carbon dioxide (CO 2 ) concentrations measured in discrete gas samples extracted from cores during drilling operations. The gaseous hydrocarbons detected by the OLGA system are predominantly CH 4 but with the regular presence of ethane (C 2 H 6 ), propane (C 3 H 8 ), isobutane (i‐C 4 H 10 ), and n‐butane (n‐C 4 H 10 ). Zones with higher CH 4 , C 2 H 6 , and C 3 H 8 concentrations were observed at depth intervals of 250–380 and 420–588 m. These higher concentrations of CH 4 , C 2 H 6 , and C 3 H 8 occur in siltstone or sandstone layers capped by claystones, suggesting that these lithological associations act as stratigraphic gas traps. The Bernard parameter (CH 4 /C 2 H 6 + C 3 H 8 ) varied from a low value of 2 at 466 m depth to a maximum value of 1904 at 621 m depth. Stable carbon isotope ratios of CH 4 show δ 13 C values between −35‰ and −25‰, suggesting the nearly ubiquitous presence of thermogenic gas. The discrete gas samples from cores exhibited CO 2 concentrations between 230 and 1400 ppm in claystones, 850 and 950 ppm in siltstones, and 240–820 ppm in sandstones, indicating higher concentrations in fine‐grained sediments. The CH 4 concentration ranges from 2 to 6 ppm in sandstone layers and from 2 to 4 ppm in siltstone and claystone layers. There is no significant correlation between CH 4 and CO 2 concentrations. These results provide evidence of light hydrocarbon migration from deeper thermally mature source rocks, with entrapment in sandstone layers capped by fine‐grained sedimentary rock layers. The high concentration of CO 2 relative to CH 4 in fine‐grained rock layers points to restricted conditions for microbial gas generation in the drilled sediments, possibly due to a combination of low organic carbon content and oxidizing conditions. This is in accordance with the abundance of reddish fine‐grained paleosols in the drilled sedimentary units. The combination of online gas monitoring and discrete sampling methods allowed the comparison between gas collected during drilling and in situ gas, contributing to a better understanding of the processes of the subsurface carbon cycle.

The geological formation of the Muschelkalk is widespread in the center of the North German Basin (NGB) and is increasingly attracting interest for application of geothermal energy extraction or high-temperature aquifer thermal energy storage (HT-ATES). This study investigates the Middle Triassic “Rüdersdorfer Schaumkalk”, which was the former injection horizon of the natural gas storage facility in Berlin, Germany. For the first time, detailed chemical and microbiological analyses of formation water of this Lower Muschelkalk limestone formation were conducted and hydrogeochemically characterized. In addition, a hydrogeochemical model was developed to quantify the potential reactions during HT-ATES focusing on calcite dissolution and precipitation. The main objectives of this study are: (1) to determine the origin of the water from the three wells targeting the Muschelkalk aquifer, (2) to understand changes in hydrochemistry after system operation, and (3) to evaluate the long-term sustainability of a potential HT-ATES system with increasing temperature. The target formation is encountered by several wells at about 525 m below the surface with an average thickness of 30 m. Two hydraulic lifting tests including physical, chemical, and microbial groundwater as well as gas monitoring were carried out. In addition, several downhole samples of formation fluid were collected from the aquifer at in situ pressure and temperature conditions. Fluid analysis of the saline formation water indicate a seawater origin within the Muschelkalk with subsequent evaporation and various water–rock interactions with anhydrite/gypsum, dolomite, and calcite. With a salinity of 130 g/L, dominated by Na–Cl, a slightly acidic pH between 6 and 7, and a low gas content of 3%, the formation water fits to other saline deep formation waters of the NGB. Gas concentrations and microbial communities like sulfate-reducing bacteria and methanogenic archaea in the produced water indicate several geochemical alterations and microbial processes like corrosion and the forming of biogenic methane. Geochemical simulations of calcite equilibrium over 10 HT-ATES cycles indicated a pronounced propensity for calcite precipitation up to 31 mg/kgw, within the heat exchanger. At the same time, these models predicted a significant potential for calcite dissolution, with rates up to 21 mg/kgw, in both the cold and hot reservoirs. The results from the carbonate aquifer characterized in this study can be transferred to other sites in the NGB affected by salt tectonics and have provided information on the microbiological-chemical processes to be expected during the initial use of old wells.

Unconventional geothermal resource development can contribute to increase power generation from renewable energy sources in countries without conventional hydrothermal reservoirs, which are usually associated with magmatic activity and extensional faulting, as well as to expand the generation in those regions where conventional resources are already used. Three recent drilling experiences focused on the characterization of unconventional resources are described and compared: the Campi Flegrei Deep Drilling Project (CFDDP) in Italy, the United Downs Deep Geothermal Power (UDDGP) project in the United Kingdom, and the DEEP Earth Energy Production in Canada. The main aspects of each project are described (geology, drilling, data collection, communication strategies) and compared to discuss challenges encountered at the tree sites considered, including a scientific drilling project (CFDDP) and two industrial ones (UDDGP and DEEP). The first project, at the first stage of pilot hole, although not reaching deep supercritical targets, showed extremely high, very rare thermal gradients even at shallow depths. Although each project has its own history, as well as social and economic context, the lessons learned at each drilling site can be used to further facilitate geothermal energy development.

Noble gas abundance and isotope data from 12 drilling mud gas samples obtained during IODP Expeditions 338 and 348 provide new insights on fluid origin and fluid migration in the inner accretionary prism below the Kumano forearc basin offshore SE Japan. The samples originate from three adjoining boreholes (C0002F, C0002N and C0002P) spanning depths between 950 and 3050 meters below sea floor (mbsf) and are composed of air and variable contributions of mantle-derived and crustal fluids.Air-corrected 3He/4He ratios of samples from Exp. 338 fall between 0.44 ± 0.24 Ra and 3.26 ± 0.28 Ra. Samples #1400 and #1800 (sample number denotes depth in mbsf) are more influenced by radiogenic helium (1.33 ± 0.34 Ra resp. 0.44 ± 0.24 Ra), whereas the air-free helium isotopic composition of sample #950 is clearly higher (3.26 ± 0.28 Ra). Enhanced radon activity around 950 mbsf, 1100 mbsf, 1400 mbsf, and 1800 mbsf suggests active flow of fluids at these depths.The helium isotopic composition of two other samples (#1700 and #1850) collected during Exp. 338 and of all samples obtained during the 1-year-later Exp. 348 are less variable (1.74–2.46 Ra with a mean 3He/4He ratio of ~ 2.4 Ra) and no radon anomalies were observed during sampling. For these samples, we assume migration by diffusive flow of helium-bearing fluids through sediments of the accretionary prism. In contrast, elevated radon activities and the more variable helium isotopic composition of fluids from 950, 1400, and 1800 mbsf from Exp. 338 are better explained by channelized and active fluid flow through temporarily permeable strata, maybe as a short-term episodic flow event caused by reactivation of buried trust faults. The helium isotopic composition of #950 is in good agreement with estimated helium isotope values of the subducting Philippine Sea Plate (PSP) at present (~ 3.4 Ra), whereas fluids from 1400 and 1800 mbsf demonstrate the input of radiogenic helium from a crustal, probably terrestrial source.

The Weihe Basin, enclosed by the Chinese Loess Plateau to the north and the Qinling Mountains to the south, is an outstanding, world-class continental site for obtaining high-resolution multi-proxy records that reflect environmental changes spanning most of the Cenozoic. Previous geophysical and sedimentary studies indicate that the basin hosts 6000–8000 m thick fluvial–lacustrine sedimentary successions spanning the Eocene to Holocene. This sedimentary record provides an excellent and unique archive to decipher long-term tectonic–climate interactions related to the uplift of the Tibetan Plateau, the onset/evolution of the Asian monsoon, and the development of the biogeography of East Asia. Owing to its location at the interface of the opposing westerly and Asian monsoon circulation systems, the Weihe Basin also holds enormous promise for providing a record of changes in these circulation systems in response to very different boundary conditions since the Eocene. To develop an international scientific drilling programme in the Weihe Basin, the Institute of Earth Environment, Chinese Academy of Sciences, organized a dedicated workshop with 55 participants from eight countries. The workshop was held in Xi'an, China, from 15 to 18 October 2019. Workshop participants conceived the key scientific objectives of the envisaged Weihe Basin Drilling Project (WBDP) and discussed technical and logistical aspects as well as the scope of the scientific collaboration in preparation for a full drilling proposal for submission to the International Continental Scientific Drilling Program (ICDP). Workshop participants mutually agreed to design a two-phase scientific drilling programme that will in a first phase target the upper 3000 m and in a second phase the entire up to 7500 m thick sedimentary infill of the basin. For the purpose of the 7500 m deep borehole, the world's only drill rig for ultra-deep scientific drilling on land, Crust 1, which previously recovered the entire continental Cretaceous sediments in the Songliao Basin, will be deployed in the WBDP.

Fault slip is a complex natural phenomenon involving multiple spatiotemporal scales from seconds to days to weeks. To understand the physical and chemical processes responsible for the full fault slip spectrum, a multidisciplinary approach is highly recommended. The Near Fault Observatories (NFOs) aim at providing high-precision and spatiotemporally dense multidisciplinary near-fault data, enabling the generation of new original observations and innovative scientific products. The Alto Tiberina Near Fault Observatory is a permanent monitoring infrastructure established around the Alto Tiberina fault (ATF), a 60 km long low-angle normal fault (mean dip 20°), located along a sector of the Northern Apennines (central Italy) undergoing an extension at a rate of about 3 mm yr−1. The presence of repeating earthquakes on the ATF and a steep gradient in crustal velocities measured across the ATF by GNSS stations suggest large and deep (5–12 km) portions of the ATF undergoing aseismic creep. Both laboratory and theoretical studies indicate that any given patch of a fault can creep, nucleate slow earthquakes, and host large earthquakes, as also documented in nature for certain ruptures (e.g., Iquique in 2014, Tōhoku in 2011, and Parkfield in 2004). Nonetheless, how a fault patch switches from one mode of slip to another, as well as the interaction between creep, slow slip, and regular earthquakes, is still poorly documented by near-field observation. With the strainmeter array along the Alto Tiberina fault system (STAR) project, we build a series of six geophysical observatory sites consisting of 80–160 m deep vertical boreholes instrumented with strainmeters and seismometers as well as meteorological and GNSS antennas and additional seismometers at the surface. By covering the portions of the ATF that exhibits repeated earthquakes at shallow depth (above 4 km) with these new observatory sites, we aim to collect unique open-access data to answer fundamental questions about the relationship between creep, slow slip, dynamic earthquake rupture, and tectonic faulting.

The Trans-Amazon Drilling Project (TADP) is reconstructing the late Cenozoic history of Amazonian geology, climate, rivers, and forests. Drilling in the Acre Basin of western Brazil in 2023 recovered an 860 m drill core characterized by sediments that were deposited in a large paleo-river system. The overall sequence includes sandstones, siltstones, and mudstones that underwent varied degrees of weathering and pedogenesis. Here, we describe the ongoing geochronologic, geochemical, mineralogical, geophysical, and biotic analyses of the sedimentary record and present some preliminary inferences of the environmental history based on these initial results.