Explore the vast range of titles available.

In this study, biocarbon was obtained from the waste material corn digest. Carbon adsorbents were obtained by physical activation of the precursor with CO2. Detailed physicochemical characterization of the biocarbon was carried out using low-temperature nitrogen adsorption/desorption, Boehm titration, zero-charge point (pHpzc) and iodine number. In addition, the sorption capacity of the biocarbon agents towards an aqueous solution of methylene blue and methyl red was determined, and the kinetics of the adsorption process were determined. The biocarbon adsorbents were characterized by an average developed specific surface area covering the range from 320 to 616 m2/g. The sorption capacity of the biocarbon adsorbents against methylene blue ranged from 40 mg/g to 146 mg/g, and for methyl red it covered the range from 31 mg/g to 113 mg/g. It was shown that the efficiency of organic dye removal by the obtained biocarbons depends on the initial concentration of the adsorbate solution, its mass, shaking rate, adsorbent–adsorbate contact time and temperature. The results obtained from the Langmuir and Freundlich kinetic models showed that the Langmuir model is the most suitable model for describing the adsorption of the studied pollutants on biocarbon. In turn, the adsorption kinetics of dyes is described according to the pseudo-second-order model. Adsorption studies also showed that as the process temperature increases, the removal efficiency of methylene blue and methyl red increases.

In this study, fennel (Foeniculum vulgare) seeds were used as a precursor to obtain carbon adsorbents through physical activation with carbon dioxide and chemical activation by impregnating the precursor with sodium carbonate. The physical activation involved the carbonization of the precursor at a temperature of 600 °C for 60 min and activation at a temperature of 800 °C for 30 min with carbon dioxide. Chemical activation included impregnation of the precursor with sodium carbonate at a mass ratio of a precursor to activator of 1:2. The mixture was activated in a nitrogen atmosphere with a flow rate at a temperature of 700 °C for 45 min. The resulting biochar samples were washed with 5% hydrochloric acid and subsequently rinsed with boiling distilled water. The biochar adsorbents were characterized using low-temperature nitrogen adsorption–desorption isotherms, Boehm titration, and pH measurements of their aqueous extracts. The specific surface area of the obtained adsorbents ranged from 89 to 345 m2/g. Biochar adsorbents exhibit a predominance of acidic groups over basic groups on their surfaces. The sorption capacities of the obtained samples towards an aqueous solution of methyl red range from 26 to 135 mg/g. Based on adsorption studies, it was found that the adsorption of the dye on the obtained biochar materials follows a pseudo-second-order model. The Freundlich isotherm best describes the studied process, indicating the formation of a multilayer of adsorbate on the adsorbent surface. The efficacy of adsorption in aqueous solutions of methyl red was found to increase with the elevation of the process temperature. Moreover, thermodynamic studies have shown that the adsorption process is spontaneous and endothermic. Consequently, this work provides a description of the physicochemical parameters of two biochars obtained by physical and chemical activation of a little-studied precursor—fennel seeds—and studies on their potential use as adsorbents for contaminants from the aqueous phase.

The preparation of biocarbons from cellulose fibres utilised in the production of baby nappy mats (sourced from Feniks Recycling company, Poland) for the removal of methylene blue and rhodamine B dyes has been documented. A Brunauer, Emmett and Teller analysis revealed a surface area within the range of 384 to 450 m2/g. The objective of this study was to investigate the removal efficiency of dyes from aqueous solutions by biocarbons, with a particular focus on the influence of various parameters, including pH, dye concentration, adsorbent dosage, shaking speed, contact time, and temperature. The maximum adsorption capacity of the dyes onto the biocarbons was found to be 85 mg/g for methylene blue and 48 mg/g for rhodamine B, respectively. The Langmuir equation proved to be the most suitable for interpreting the sorption of organic dyes. The adsorption process was found to exhibit a chemisorption mechanism, effectively mirroring the pseudo-second-order kinetics. Furthermore, the adsorption of dyes was observed to be endothermic (the enthalpy change was positive, 9.1–62.6 kJ/mol) and spontaneous under the tested operating conditions. The findings of this study indicate that biocarbons represent a cost-effective option for the removal of methylene blue and rhodamine B. The adsorption method was observed to be an effective and straightforward approach for the removal of these dyes. The results of the Boehm titration analysis and zero charge point value indicated that the synthesised biomaterials exhibited a slightly basic surface character.

The aim of this study was to obtain a series of activated carbon samples by the chemical activation of low-rank coal. The precursor was impregnated with a NaOH solution. Activated carbons were characterized by determining their textural parameters and content of surface oxygen functional groups and by using an elemental analysis. The carbons were tested as potential adsorbents for the removal of liquid pollutants represented by rhodamine B. The effectiveness of rhodamine B removal from water solutions depended on the initial concentration of the dye, the mass of rhodamine B, and the pH and temperature of the reaction. The isotherm examination followed the Langmuir isotherm model. The maximum adsorption capacity of the rhodamine B was 119 mg/g. The kinetic investigation favored the pseudo-second-order model, indicating a chemisorption mechanism. The thermodynamic assessment indicated spontaneous and endothermic adsorption, with decreased randomness at the solid–liquid interface. The experiment revealed that a 0.1 M HCl solution was the most effective regenerative agent.

This paper presents the results of studies on the life span, survival, weight and fecundity of the forest cockchafer (Melolontha hippocastani, Fabricius, 1801) and the common cockchafer (Melolontha melolontha, Linnaeus, 1758) beetle feeding on Alnus glutinosa (L.) Gaertn., Betula pendula Roth., Carpinus betulus L., Fagus sylvatica L., Larix decidua Mill., Prunus serotina (Ehr.) Borkh., Quercus petraea (Matt.) Liebl., Quercus robur L., Robinia pseudoacacia L., Sambucus nigra L. and Sorbus aucuparia L. em. Hedl. The lifespan and weight of beetles as well as female fertility were examined in 2011 and 2013. Specimen for laboratory tests were collected in the field shortly after leaving their overwintering sites in the soil and identical experimental protocols were applied to both examined species. 576 and 432 beetles were tested in 2011 and 2013, respectively. In 2011, beetles were feeding on A. glutinosa, B. pendula, F. sylvatica, L. decidua Q. petraea leaves and on C. betulus, P. serotina, R. pseudoacacia, S. aucuparia and S. nigra in 2013. Both years, beetles feeding on Q. robur leaves were examined as a control. Our results showed that feeding on leaves of Q. robur and Q. petraea had the largest positive impact on the life time, weight and fecundity of the studied beetles. Leaves of F. sylvatica and L. decidua also constituted an adequate food source for the development of M. melolontha. M. hippocastani, however, did not perform as well when feeding on these two tree species. Females of M. melolontha reared on leaves of B. pendula did not lay eggs. The following plant species had a negative impact on the survival and development of the collected specimen and female fertility: A. glutinosa, S. nigra, P. serotina and R. pseudoacacia. Neither beetle species fed on the leaves of A. glutinosa or S. nigra.

The idea of Industry 4.0 is a stage of revolution in terms of new solutions and advanced technology, as well as artificial intelligence. Micro and macroeconomic factors generate the need to modify logistics and production processes in enterprises. One of the changes is the organization of warehouse management. The aim of the article is to indicate the possibility of using RFID technology in conjunction with Laser Telemetry in the location of objects in space along with the visualization of this location. In addition, the study aims to merge passive RFID technology with laser scanning to produce a system that can identify and locate objects in a virtual Computer-Aided Design (CAD)—based 3Dimensional (3D) environment. The described case study is the result of research conducted as part of the implementation project. This paper describes the steps to be taken and the creation of a system that will use RFID technology and that will enable the identification of objects in the space of computer systems. For this purpose, it was possible to create a system that will identify objects using RFID and Laser Telemetry in 3D space.

The waste materials left after supercritical extraction of hop cones and marigold flowers were tested as precursors of activated bio-carbons. Adsorbents were produced by means of the physical (also called thermal) activation method using CO2 as the gasifying agent. All the activated bio-carbons were tested for the removal of NO2 and H2S from the gas phase under dry and wet conditions. The effects of the type of precursor and the activation procedure on the porous structure development, the acid-base properties of the surface, as well as the sorption capacities of the materials produced were also checked. The final products were bio-carbons of medium developed surface area with a basic surface nature, characterized by their high effectiveness in removal of gas pollutants of acidic character, especially nitrogen dioxide (sorption capacities in the range from 12.5 to 102.6 mg/g). It was proved that the toxic gas removal efficiency depends considerably on the sorption conditions and the activation procedure. All materials showed greater effectiveness in gas removal when the process of adsorption was carried out in the presence of steam.

This study presents the production of activated carbon through the direct physical activation of oak bark using carbon (IV) oxide. The activation process was conducted at three distinct temperatures of 700 °C, 800 °C, and 900 °C. The activation time was 60 min. A comprehensive series of analytical procedures was performed on the resultant adsorbents. These included elemental analysis, determination of textural parameters, Boehm titration, pH determination of aqueous extracts, pHpzC0, assessment of ash content, and elemental and XPS analysis. Subsequently, adsorption tests for butyl paraben and methylene blue were carried out on the materials obtained. The total surface area of the sorbents ranged from 247 m2/g to 696 m2/g. The acid-based properties of the samples tested were examined, and the results indicated that the sorbents exhibited a distinct alkaline surface character. The sorption capacities of the tested samples for butylparaben ranged between 20 and 154 mg/g, while the capacities for methylene blue varied between 13 and 224 mg/g. The constants of the Langmuir and Freundlich models were determined for each of the impurities, as well as the thermodynamic parameters. The present study investigates the influence of contact time between adsorbent and adsorbate, in addition to the kinetics of the adsorption processes. The activated carbon samples obtained demonstrated satisfactory sorption capacities, with the material obtained at 900 °C exhibiting the best sorption capacities.

In the present work, we reported on the efficiency of the removal of organic dyes by adsorption on activated carbons prepared from the residue of supercritical extraction of marigold. The performance of adsorbents prepared was tested towards methyl red, methylene blue, malachite green, and crystal violet at room temperature. The effects of carbonization (500 and 700 °C) and activation (700 and 800 °C) temperatures, textural parameters, and acid-base character of the adsorbent surface on the sorption properties of the activated carbons were established. Activated carbons are characterized by low developed specific surface area, from 2 to 206 m2/g, and have a basic character of the surface (pH of carbons water extracts ranging from 10.4 to 11.2). Equilibrium adsorption isotherms were investigated. The equilibrium data were analyzed in the Langmuir, Freundlich, and Temkin models. The adsorption capacities of activated carbons studied varied from 47.62 to 102.43 mg/g towards methyl red, 53.14 to 139.72 mg/g towards methyl red, 425.46 to 622.80 towards malachite green and 155.91 to 293.75 mg/g towards crystal violet, from their water solutions. Kinetics of the adsorption of the organic dyes studied were found to be described by the pseudo-second-order model. It was proven that through the physical activation of the residue of supercritical extraction of marigold, it is possible to obtain carbonaceous materials of very high adsorption capacity towards organic pollutants.

Natural User Interfaces (NUI) are now widely used in electronic devices such as smartphones, tablets and gaming consoles. We have tried to apply this technology in the teaching of chemistry in middle school and high school. A virtual chemical laboratory was developed in which students can simulate the performance of laboratory activities similar to those that they perform in a real laboratory. Kinect sensor was used for the detection and analysis of the student's hand movements, which is an example of NUI. The studies conducted found the effectiveness of educational virtual laboratory. The extent to which the use of a teaching aid increased the students' progress in learning chemistry was examined. The results indicate that the use of NUI creates opportunities to both enhance and improve the quality of the chemistry education. Working in a virtual laboratory using the Kinect interface results in greater emotional involvement and an increased sense of self-efficacy in the laboratory work among students. As a consequence, students are getting higher marks and are more interested in the subject of chemistry.