Explore the vast range of titles available.

Quasi-two-dimensional (quasi-2D) perovskites have attracted extraordinary attention due to their superior semiconducting properties and have emerged as one of the most promising materials for next-generation light-emitting diodes (LEDs). The outstanding optical properties originate from their structural characteristics. In particular, the inherent quantum-well structure endows them with a large exciton binding energy due to the strong dielectric- and quantum-confinement effects; the corresponding energy transfer among different n-value species thus results in high photoluminescence quantum yields (PLQYs), particularly at low excitation intensities. The review herein presents an overview of the inherent properties of quasi-2D perovskite materials, the corresponding energy transfer and spectral tunability methodologies for thin films, as well as their application in high-performance LEDs. We then summarize the challenges and potential research directions towards developing high-performance and stable quasi-2D PeLEDs. The review thus provides a systematic and timely summary for the community to deepen the understanding of quasi-2D perovskite materials and resulting LED devices.

Rapid Auger recombination represents an important challenge faced by quasi-2D perovskites, which induces resulting perovskite light-emitting diodes’ (PeLEDs) efficiency roll-off. In principle, Auger recombination rate is proportional to materials’ exciton binding energy ( E b ). Thus, Auger recombination can be suppressed by reducing the corresponding materials’ E b . Here, a polar molecule, p -fluorophenethylammonium, is employed to generate quasi-2D perovskites with reduced E b . Recombination kinetics reveal the Auger recombination rate does decrease to one-order-of magnitude lower compared to its PEA + analogues. After effective passivation, nonradiative recombination is greatly suppressed, which enables resulting films to exhibit outstanding photoluminescence quantum yields in a broad range of excitation density. We herein demonstrate the very efficient PeLEDs with a peak external quantum efficiency of 20.36%. More importantly, devices exhibit a record luminance of 82,480 cd m −2 due to the suppressed efficiency roll-off, which represent one of the brightest visible PeLEDs yet. Designing efficient perovskite light-emitting diodes remains a challenge due to the strong Auger recombination and resulting Joule heating. Here, the authors propose polarizable p -fluorophenethylammonium to generate quasi-2D perovskites with reduced binding energy developing perovskite light-emitting diodes with a peak EQE of 20.36% and a maximum luminance of 82,480 cdm -2 .

Efficient ultra-broadband emitter is realized by using lanthanide ion doping coupled with “DPs-in-glass composite” (DiG) structure. The synergy of self-trapped exciton together with the energy transition induce this ultra-broadband emission emerge.Efficient ultra-broadband emitter is realized by using multi-Ln-doped Cs2Ag(In/Bi)Cl6 lead-free double perovskite (DP) coupled with “DPs-in-glass composite” (DiG) structure. The synergy of self-trapped exciton together with the energy transition induces this ultra-broadband emission emerge.

Reduced-dimensional (quasi-2D) perovskite materials are widely applied for perovskite photovoltaics due to their remarkable environmental stability. However, their device performance still lags far behind traditional three dimensional perovskites, particularly high open circuit voltage ( V oc ) loss. Here, inhomogeneous energy landscape is pointed out to be the sole reason, which introduces extra energy loss, creates band tail states and inhibits minority carrier transport. We thus propose to form homogeneous energy landscape to overcome the problem. A synergistic approach is conceived, by taking advantage of material structure and crystallization kinetic engineering. Accordingly, with the help of density functional theory guided material design, (aminomethyl) piperidinium quasi-2D perovskites are selected. The lowest energy distribution and homogeneous energy landscape are achieved through carefully regulating their crystallization kinetics. We conclude that homogeneous energy landscape significantly reduces the Shockley-Read-Hall recombination and suppresses the quasi-Fermi level splitting, which is crucial to achieve high V oc . Quasi-2D halide perovskites are good candidates for efficient and stable solar cells but they suffer from high open-circuit voltage ( V oc ) deficit. Here He et al. show that homogeneous energy landscape of the charge transport levels is important to suppressing the recombination and increasing V oc .

Serious performance decline arose for perovskite light-emitting diodes (PeLEDs) once the active area was enlarged. Here we investigate the failure mechanism of the widespread active film fabrication method; and ascribe severe phase-segregation to be the reason. We thereby introduce L-Norvaline to construct a COO − -coordinated intermediate phase with low formation enthalpy. The new intermediate phase changes the crystallization pathway, thereby suppressing the phase-segregation. Accordingly, high-quality large-area quasi-2D films with desirable properties are obtained. Based on this, we further rationally adjusted films’ recombination kinetics. We reported a series of highly-efficient green quasi-2D PeLEDs with active areas of 9.0 cm 2 . The peak EQE of 16.4% is achieved in  = 3, represent the most efficient large-area PeLEDs yet. Meanwhile, high brightness device with luminance up to 9.1 × 10 4  cd m −2 has achieved in = 10 film. Performance of perovskite LED tends to decline as the active area increases, thus understanding the failure mechanism is paramount to surmount this limitation. Here, the authors report severe phase-segregation to be the cause, and introduce L-Norvaline to overcome it, as the result, highly-efficient 9.0 cm 2 green PeLED is realised.

Quasi-two-dimensional (quasi-2D) Ruddlesden–Popper (RP) perovskites such as BA 2 Cs n –1 Pb n Br 3 n +1 (BA = butylammonium, n  > 1) are promising emitters, but their electroluminescence performance is limited by a severe non-radiative recombination during the energy transfer process. Here, we make use of methanesulfonate (MeS) that can interact with the spacer BA cations via strong hydrogen bonding interaction to reconstruct the quasi-2D perovskite structure, which increases the energy acceptor-to-donor ratio and enhances the energy transfer in perovskite films, thus improving the light emission efficiency. MeS additives also lower the defect density in RP perovskites, which is due to the elimination of uncoordinated Pb 2+ by the electron-rich Lewis base MeS and the weakened adsorbate blocking effect. As a result, green light-emitting diodes fabricated using these quasi-2D RP perovskite films reach current efficiency of 63 cd A −1 and 20.5% external quantum efficiency, which are the best reported performance for devices based on quasi-2D perovskites so far. Owing to large exciton binding energy, quasi-2D perovskite is promising for light-emitting application, yet inhomogeneous phases distribution limits the potential. Here, the authors improve the performance by using MeS additive to regulate the phase distribution and to reduce defect density in the films.

Device performance and in particular device stability for blue perovskite light-emitting diodes (PeLEDs) remain considerable challenges for the whole community. In this manuscript, we conceive an approach by tuning the ‘A-site’ cation composition of perovskites to develop blue-emitters. We herein report a Rubidium-Cesium alloyed, quasi-two-dimensional perovskite and demonstrate its great potential for pure-blue PeLED applications. Composition engineering and in-situ passivation are conducted to further improve the material’s emission property and stabilities. Consequently, we get a prominent film photoluminescence quantum yield of around 82% under low excitation density. Encouraged by these findings, we finally achieve a spectra-stable blue PeLED with the peak external quantum efficiency of 1.35% and a half-lifetime of 14.5 min, representing the most efficient and stable pure-blue PeLEDs reported so far. The strategy is also demonstrated to be able to generate efficient perovskite blue emitters and PeLEDs in the whole blue spectral region (from 454 to 492 nm). Besides device operational stability, the color stability is also an important challenge for the perovskite light-emitting diodes, especially the blue ones. Here Jiang et al. report the most efficient and color stable pure-blue perovskite LEDs so far, with a half-lifetime of 14.5 minutes.

Perovskite light-emitting diodes (PeLEDs) with an external quantum efficiency exceeding 20% have been achieved in both green and red wavelengths 1 – 5 ; however, the performance of blue-emitting PeLEDs lags behind 6 , 7 . Ultrasmall CsPbBr 3 quantum dots are promising candidates with which to realize efficient and stable blue PeLEDs, although it has proven challenging to synthesize a monodispersed population of ultrasmall CsPbBr 3 quantum dots, and difficult to retain their solution-phase properties when casting into solid films 8 . Here we report the direct synthesis-on-substrate of films of suitably coupled, monodispersed, ultrasmall perovskite QDs. We develop ligand structures that enable control over the quantum dots’ size, monodispersity and coupling during film-based synthesis. A head group (the side with higher electrostatic potential) on the ligand provides steric hindrance that suppresses the formation of layered perovskites. The tail (the side with lower electrostatic potential) is modified using halide substitution to increase the surface binding affinity, constraining resulting grains to sizes within the quantum confinement regime. The approach achieves high monodispersity (full-width at half-maximum = 23 nm with emission centred at 478 nm) united with strong coupling. We report as a result blue PeLEDs with an external quantum efficiency of 18% at 480 nm and 10% at 465 nm, to our knowledge the highest reported among perovskite blue LEDs by a factor of 1.5 and 2, respectively 6 , 7 . Ultrasmall monodisperse perovskite quantum dots are synthesized in situ on a substrate via ligand structure regulation, yielding the highest external quantum efficiency blue perovskite LEDs reported so far.

Low-dimensional perovskites have—in view of their high radiative recombination rates—shown great promise in achieving high luminescence brightness and colour saturation. Here we investigate the effect of electron–phonon interactions on the luminescence of single crystals of two-dimensional perovskites, showing that reducing these interactions can lead to bright blue emission in two-dimensional perovskites. Resonance Raman spectra and deformation potential analysis show that strong electron–phonon interactions result in fast non-radiative decay, and that this lowers the photoluminescence quantum yield (PLQY). Neutron scattering, solid-state NMR measurements of spin–lattice relaxation, density functional theory simulations and experimental atomic displacement measurements reveal that molecular motion is slowest, and rigidity greatest, in the brightest emitter. By varying the molecular configuration of the ligands, we show that a PLQY up to 79% and linewidth of 20 nm can be reached by controlling crystal rigidity and electron–phonon interactions. Designing crystal structures with electron–phonon interactions in mind offers a previously underexplored avenue to improve optoelectronic materials' performance.

Hybrid perovskites are promising semiconductors for optoelectronic applications. However, they suffer from morphological disorder that limits their optoelectronic properties and, ultimately, device performance. Recently, perovskite single crystals have been shown to overcome this problem and exhibit impressive improvements: low trap density, low intrinsic carrier concentration, high mobility, and long diffusion length that outperform perovskite-based thin films. These characteristics make the material ideal for realizing photodetection that is simultaneously fast and sensitive; unfortunately, these macroscopic single crystals cannot be grown on a planar substrate, curtailing their potential for optoelectronic integration. Here we produce large-area planar-integrated films made up of large perovskite single crystals. These crystalline films exhibit mobility and diffusion length comparable with those of single crystals. Using this technique, we produced a high-performance light detector showing high gain (above 10 4 electrons per photon) and high gain-bandwidth product (above 10 8  Hz) relative to other perovskite-based optical sensors. Single crystals of organolead halide perovskites exhibit large carrier mobilities and long diffusion lengths. Here, the authors succeed in growing the single crystals on planar substrates and integrate them as the active layer of visible photodetectors with a large gain-bandwidth product.