Explore the vast range of titles available.

With Nb-Ti-stabilized 430 ferritic stainless steel（NTS430FSS） and SUS 430 ferritic stainless steel（SUS430FSS） as experimental materials, the influence of precipitation on intergranular corrosion resistance was investigated. A series of aging treatment were carried out. The free-exposure corrosion test and double loop electrochemical potentiokinetic reactivation（DL-EPR） test with a scan rate of 1.67 m V/s at 26 °C were applied to evaluate the intergranular corrosion（IGC） resistance. Metallographic observation, scanning electron microscope（SEM）, transmission electron microscope（TEM） with energy dispersive spectroscopy（EDS） and X-ray diffraction（XRD） analysis were conducted. The results show that IGC occurred in SUS430 FSS aged above 700 °C, while it occurred in NTS430 FSS as the temperature was improved to 1 050 °C. The critical degree of sensitization Ir/Ia reaches 0.305 in SUS430 FSS, which is higher than that of NTS430 FSS, i.e. 0.010, aged at 950 °C for 2 h. The TEM, EDS and XRD results show that a large amount of Cr23C6 precipitates with size of 60 nm×22 nm are located at the SUS430 FSS grain boundaries as chains. With the addition of Nb and Ti and reduction of C, the amount of precipitates reduces significantly in NTS430 FSS. A majority of Cr23C6 were replaced by Ti C and Nb C. Only a small amount of spherical Ti C（R=186 nm） and square Ti N（312 nm×192 nm） with Nb and Cr adsorbed are left along grain boundaries. Due to the dual stabilization of Nb and Ti, the precipitation of Cr23C6 is restrained, the chromium depleted region is avoided and accordingly the resistance to the intergranular corrosion is improved.

The hot deformation behavior of ultra purified 17% Cr ferritic stainless steel stabilized with Nb and Ti was investigated using axisymmetric hot compression tests on a thermomechanical simulator.The deformation was carried out at the temperatures ranging from 700 to 1 100℃ and strain rates from 1to 10s-1.The microstructure was investigated using electron backscattering diffraction.The effects of temperature and strain rate on deformation behavior were represented by Zener-Hollomon parameter in an exponent type equation.The effect of strain was incorporated in the constitutive equation by establishing polynomial relationship between the material constants and strain.A sixth order polynomial was suitable to represent the effect of strain.The modified constitutive equation considering the effect of strain was developed and could predict the flow stress throughout the deformation conditions except at800℃in 1s-1 and at 700℃in 5and 10s-1.Losing the reliability of the modified constitutive equation was possibly ascribed to the increase in average Taylor factor at 800℃in 1s-1 and the increase in temperature at 700℃in 5and10s-1 during hot deformation.The optimum window for improving product quality of the ferritic stainless steels was identified as hot rolling at a low finisher entry temperature of 700℃,which can be achieved in practical production.

It is promising for metal especially ferritic stainless steel（FSS）to be used as interconnector when the solid oxide fuel cell（SOFC）is operated at temperature lower than 800℃.However,there are many challenges for FSS such as anti-oxidant,poisoning to cathode and high area specific resistance（ASR）when using as SOFC interconnector.The effect of Cr content（12-30 mass%）in Fe-Cr alloys on thermal expansion coefficient（TEC）,oxidation resistance,microstructure of oxidation scale and ASR was investigated by thermo-gravimetry,scanning electron microscopy,energy dispersive spectroscopy and four-probe DC technique.The TEC of Fe-Cr alloys is（11-13）×10~（-6） K~（-1）,which excellently matches with other SOFC components.Alloys have excellent oxidation resistance when Cr content exceeds 22mass% because of the formation of chromium on the surface of alloy.The oxidation rate constants kdand ksdecrease rapidly with increasing the Cr content and then increase slowly when the Cr content is higher than 22mass%.The kinetic results indicate that Cr evaporation must be considered at high temperature for Fe-Cr alloys.After the alloys were oxidized in air at 800℃ for500 h,log（ASR/T）（Tis the absolute temperature）presents linear relationship with 1/T and the conduct activation energy is 0.6-0.8eV（Cr16-30）.Optimal Cr content is 22-26mass%considering the oxidation resistance and ASR.

The influence of cerium addition on the isothermal oxidation behavior of 00Cr17NbTi ferritic stainless steel was studied at temperature up to 1,000 ℃ for 100 h in air. The results show that cerium additions can reduce the grain size of this ferritic stainless steel, improve the diffusion of chromium and decrease the critical concentration of chromium to form protective Cr2O3 layer. With the increasing of cerium addition, the oxide particles become smaller and this can increase the rupture strength and spalling resistance of oxide layers. The transport mechanism through the oxide layer is varied from metal transport outward from steel to principally oxygen transport inward with the increase of cerium content, which leads to the lower oxidation rate and the better scale adherence of 00Cr17NbTi ferritic stainless steel.

Texture inhomogeneity usually takes place in ferritic stainless steels due to the lack of phase transformation and recrystallization during hot strip rolling,which can deteriorate the formability of final sheets.In order to work out the way of weakening texture inhomogeneity,conventional hot rolling and warm rolling processes have been carried out with an ultra purified ferritic stainless steel.The results showed that the evolution of through-thickness texture is closely dependent on rolling process,especially for the texture in the center layer.For both conventional and warm rolling processes,shear texture components were formed in the surface layers after hot rolling and annealing;sharp α-fiber and weakγ-fiber with the major component at{111}〈110〉 were developed in both cold rolled sheet surfaces,leading to the formation of inhomogeneousγ-fiber dominated by{111}〈112〉after recrystallization annealing.In the center layer of conventional rolled and annealed bands,strongα-fiber and weakγ-fiber textures were formed;the cold rolled textures were comprised of sharpα-fiber and weakγ-fiber with the major component at{111}〈110〉,and inhomogeneousγ-fiber dominated by{111}〈112〉 was formed after recrystallization annealing.By contrast,in the centre layer of warm rolled bands,the texture was comprised of weakα-fiber and sharpγ-fiber,andγ-fiber became the only component after annealing.The cold rolled texture displayed a sharpγ-fiber with the major component at{111}〈112〉and the intensity ofγ-fiber close to that ofα-fiber,resulting in the formation of a nearly homogeneousγ-fiber recrystallization texture in the center layer of the final sheet.

In order to understand the effect of Mo element on the high-temperature fatigue behavior of 15CrNbTi ferritic stainless steel, the stress-controlled fatigue tests have been performed for both 15CrNbTi and 15Cr0.5MoNbTi ferritic stainless steels at 800 ℃ in laboratory air. The fatigue test results indicate that the fatigue resistance of 15Cr0.5MoNbTi steel is manifestly higher than that of 15CrNbTi steel at the maximum stress below 57 MPa; the 15Cr0.5MoNbTi steel possesses a fatigue limit of 35 MPa, which is higher than that of 15CrNbTi steel. The TEM observations reveal that the Mo element can suppress the formation of coarsened Fe3Nb3C precipitates and result in the fatigue resistance enhancement. The dislocation networks formed during the cyclic load favor to improve the fatigue resistance of 15Cr0.5MoNbTi steel at 800 ℃.

This article reports the effects of Sn on the inclusions as well as the mechanical properties and hot workability of ferritic stainless steel. Precipitation phases and inclusions in Sn-bearing ferritic stainless steel were observed, and the relationship between the workability and the microstructure of the steel was established. Energy-dispersive X-ray spectroscopic analysis of the steel reveals that an almost pure Sn phase forms and MnS-Sn compound inclusions appear in the steel with a higher Sn content. Little Sn segregation was observed in grain boundaries and in the areas around sulfide inclusions;however, the presence of Sn does not adversely affect the workability of the steel con-taining 0.4wt%Sn. When the Sn content is 0.1wt%-0.4wt%, Sn improves the tensile strength and the plastic strain ratio and also improves the plasticity with increasing temperature. A mechanism of improving the workability of ferritic stainless steel induced by Sn addition was discussed：the presence of Sn lowers the defect concentration in the ultra-pure ferritic lattice and the good distribution of tin in the lattice overcomes the problem of hot brittleness that occurs in low-carbon steel as a result of Sn segregation.

The effects of Ni content and heat-treatment process on the toughness of a super ferritic stainless steel with 26 wt% Cr and 3.5 wt% Mo were investigated. It was found that with the increase of Ni content, the Charpy impact toughness improved remarkably, and transformed from cleavage brittle fracture to the most ductile fracture. There were no obvious differences between the high- and low-Ni contents on the microstructure and mechanical properties since the addition of Ni did not influence crystal structure, phase composition, and precipitation of ultra pure ferritic stainless steels. Meanwhile, the heat-treatment process was a key point to maintain a high level of toughness by optimizing structure and removing detrimental precipitation, i.e., chi phase.

The microstructure analysis and mechanical properties evaluation of laser beam welded AISI 409M ferritic stainless steel joints are investigated. Single pass autogeneous welds free of volumetric defects were produced at a welding speed of 3 000 mm/min. The joints were subjected to optical microscope, scanning electron fractographe, microhardness, transverse and longitudinal tensile, bend and charpy impact toughness testing. The coarse ferrite grains in the base metal were changed into dendritic grains as a result of rapid solidification of laser beam welds. Tensile testing indicates overmatching of the weld metal is relative to the base metal. The joints also exhibited acceptable impact toughness and bend strength properties.

The effects of Mg addition on the formation of nonmetallic inclusions and solidification structure of Ti-sta- bilized ultra-pure ferritie stainless steels were investigated by experimentally casting ingots with different composi tions. Thermodynamic analyses on the formation of complex inclusions after adding Mg into steels were carried out combined with the scanning electron microscopy energy dispersive spectrometry （SEM EDS） analysis. And the EDS analysis showed that in steel samples with Mg addition, a new spinel crystal phase combined with AI2O3- TiOx formed. It was also found that after Mg addition, the proportions of equiaxed grain zone of 409L, 4003, 439 and 443NT steels increased from 10.2%, 21.8%, 13.4% and 18.6% to 84.3%, 92.3%, 91.1% and 100.0%, respec tively. Since the planar disregistry between spinel and TiN is 5. 1%0, spinel could promote the precipitation of TiN and increase the number density of TiN inclusions in steel melts. The mechanism of solidification structure refinement after adding Mg into steels supposed that the complex inclusions of spinel and TiN in high number density enhanced columnar-to-equiaxed transition, since the planer disregistry between δ phase and spinel is 1.4 %.