Explore the vast range of titles available.

In this paper, simulations of deep drawing tests at elevated temperatures were carried out with experimental validation. The aim of this work was to study the effect of process parameters on formability and mechanical properties of aluminum alloy 7075 in hot stamping process.Process parameters, including blank temperature, stamping speed, blank holder force and friction coefficient, were studied. Stamping tests were conducted at temperatures between 350 and 500 ℃, blank holder force between 0 and 10 kN, stamping speed between 50 and 150 mm·s^-1, and friction coefficient between 0.1 and 0.3. Based on the analysis, it is shown that thickness homogeneity could be improved when the blank is formed at lower temperature,lower blank holder force and lower friction coefficient.Formability could be improved when the blank was well lubricated at about 400 ℃. Formability at stamping speed 50 mm·s^-1 is far better than those at other speeds. The mechanical property analysis shows that the hot stamping process could make the formed part to obtain high quality.

The effects of isothermal treatments on the microstructural evolution and coarsening rate of semi-solid 7075 aluminum alloy produced via the recrystallization and partial remelting （RAP） process were investigated. Samples of 7075 aluminum alloy were subjected to cold extrusion, and semi-solid treatment was carried out for 5-30 min at temperatures ranging from 580 to 605℃. A backward-extrusion experiment was conducted to investigate liquid segregation during the thixoforming process. The results revealed that obvious grain coarsening and spheroidization occurred during prolonged isothermal treatments. In addition, higher soaking temperatures promoted the spheroidization and coarsening process because of the increased liquid fraction and the melting of second phases. Segregation of the liquid phase caused by the difference in fluidity between the liquid and the solid phases was observed in different regions of the thixoformed specimens.

The hardness, the tensile and the high-cycle fatigue（HCF） performances of 7075 aluminum alloy were investigated under temper T651, solution treated at 380 ℃ for 0.5 h and aged at different temperatures（150, 170, 190 ℃） for 10 hours. The optimal microstructures and the fatigue fracture surfaces were observed. The results show that the hardness and the tensile performances are at their optimum at T651, but the fatigue life is the shortest. The hardness and the elongation are the lowest after solution treatment. With the aging temperature increasing（150-190 ℃）, the HCF is improved. The crack is initiated from the impurity particles on the subsurface. Treated at 170 ℃,the area of the quasi-cleavage plane and the width of parallel serrated sections of the crack propagation are the largest. With increasing aging temperature, the dimple size of finally fracture surfaces becomes larger and the depth deeper.

A new process consisting of the spray forming and the continuous extrusion forming for manufacturing 7075A1 alloy was proposed. The microstructure evolution, mechanical properties and the resistance to stress corrosion cracking of the alloy were studied. The results indicate that the spray forming process induces obviously grain refinement and greatly lower segregation microstructure. Besides, the Conform process produces finer grains and conduces to more uniform distribution of the precipitates of A1Cu and MgZn2 phases. The fabricated alloy shows good comprehensive mechanical properties and superb performance of stress corrosion resistance. Moreover, a better combination of the mechanical properties and the resistance to stress corrosion cracking could then be obtained under a certain condition of atomization gas pressure of 0.19 MPa. The enhanced properties are attributed to the following factors, which include the grain refinement, the fine and homogeneous distribution of A1Cu and MgZn2 phases, the high density of the extruded products, as well as the discontinuous distribution of the grain boundaries after retrogression and reaging （RRA） heat treatment.

The microstructure, tensile property and wear resistance of 7075 aluminum matrix composite reinforced with TiC particles prepared by in-situ reaction casting were investigated. The effect of TiC reinforcement on wear behavior was analyzed. The wear mechanism was also discussed. A micro-mechanism model of reaction kinetics for synthesis of TiC was acquired. Results show that TiC could increase the tensile and yield strength, but decrease the elongation. Besides, TiC particles improve the property of wear resistance of 7075 aluminum alloy. The wear mechanisms include abrasive wear and adhesive wear in wear test process.

We have experimentally determined the as-cast structures of semi-continuous casting 7075 aluminum alloy obtained in the pres-ence of dual-frequency electromagnetic field. Results suggest that the use of dual-frequency electromagnetic field during the semi-continuous casting process of 7075 aluminum alloy ingots reduces the thickness of the surface segregation layer, increases the height of the melt menis-cus, enhances the surface quality of the ingot, and changes the surface morphology of the melt pool. Moreover, low-frequency electromag-netic field was found to show the most obvious influence on improving the as-cast structure because of its high permeability in conductors.