Explore the vast range of titles available.

In the laser sintering technology, the semi-crystalline polymer material is exposed to elevated temperatures during processing, which leads to serious material ageing for most materials. This has already been investigated intensively by various authors. However, the ageing of the material at ambient temperatures during shelf life has not been the focus so far. The need to analyse the shelf life can be derived from an ecological and economic point of view. This work is focusing on the shelf life of PA2200 (PA12). To reduce the potential influences of powder production fluctuations, two different powder batches stored for 5.5 years and 6.5 years are investigated and compared to a reference powder produced 0.5 years before these investigations. Multiple powder analyses and part characterisations have been performed. A significant yellowing and molecular chain length reduction can be derived from the measurement results. Whereas the influence on mechanical part performance was minor, the parts built with the stored powders are more yellowish. As it is most likely that this is due to the consumption of polyamide stabilisers, it can be assumed that these parts will be subject to significantly faster ageing. Therefore, it is still not recommended to use the stored powders for critical parts or light intense and humid environments.

Electrical cable insulation, mainly composed of polymeric materials, progressively deteriorates under thermal, electrical, mechanical, and environmental stress factors. This degradation reduces dielectric strength, thermal stability, and mechanical integrity, thereby increasing susceptibility to failure modes such as partial discharges, arcing, and surface tracking—recognized precursors of fire ignition. This review consolidates current knowledge on the degradation pathways of cable insulation and their direct link to fire hazards. Emphasis is placed on mechanisms including thermal-oxidative aging, electrical treeing, surface tracking, and thermal conductivity decline, as well as the complex interactions introduced by flame-retardant additives. A bibliometric analysis of 217 publications reveals strong clustering around material degradation phenomena, while underlining underexplored areas such as ignition mechanisms, diagnostic monitoring, and system-level fire modeling. Comparative experimental findings further demonstrate how insulation aging modifies ignition thresholds, heat release rates, and smoke toxicity. By integrating perspectives from materials science, electrical engineering, and fire dynamics, this review establishes the nexus between aging mechanisms and fire hazards.

The objective of the study is development of a creep kernel recording form, which allows obtaining representations for creep curves calculation. Based on the elastic-creeping body theory a possibility of the high-rate creep movement analytical study has been shown. A creep kernel, which contains a formula to describe the aging material properties, has been built. Essential stages of the proposed creep kernel formation have been given. The correspondence of the proposed calculations to real processes has been proved by a comparison with experimental data. In the numerical implementation, decomposition of integration elements into power series has been used. A possibility of calculating functions for a long time interval has been shown. Creep kernel parameters have been determined on the basis of experimental data of early age concrete samples by minimizing the standard deviation of theoretical and empirical values.

There is growing appreciation of the role that the extracellular environment plays in regulating cell behavior. Mechanical, structural, and compositional cues, either alone or in concert, can drastically alter cell function. Biomaterials, and particularly hydrogels, have been developed and implemented to present defined subsets of these cues for investigating countless cellular processes as a means of understanding morphogenesis, aging, and disease. Although most scientists concede that standard cell culture materials (tissue culture plastic and glass) do a poor job of recapitulating native cellular milieus, there is currently a knowledge barrier for many researchers in regard to the application of hydrogels for cell culture. Here, we introduce hydrogels to those who may be unfamiliar with procedures to culture and study cells with these systems, with a particular focus on commercially available hydrogels.

A linear thermoviscoelastic model for homogeneous, aging materials with memory is established. A system of integro-differential equations is obtained by using two motions (a one-dimensional motion and a shearing motion) for this model. Applying the group analysis method to the system of integro-differential equations, the admitted Lie group is determined. Using this admitted Lie group, invariant and partially invariant solutions are found. The present paper gives a first example of application of partially invariant solutions to integro-differential equations.

Biomolecular condensates are viscoelastic materials. Here we investigate the determinants of the sequence-encoded and age-dependent viscoelasticity of condensates formed by the prion-like low-complexity domain of the protein hnRNP A1 and its designed variants. We find that the dominantly viscous forms of the condensates are metastable Maxwell fluids. A Rouse–Zimm model that accounts for the network-like organization of proteins within condensates reproduces the measured viscoelastic moduli. We show that the strengths of aromatic inter-sticker interactions determine sequence-specific amplitudes of elastic and viscous moduli and the timescales over which elastic properties dominate. These condensates undergo physical ageing on sequence-specific timescales. This is driven by mutations to spacer residues that weaken the metastability of dominantly viscous phases. The ageing of condensates is accompanied by disorder-to-order transitions, leading to the formation of non-fibrillar, β-sheet-containing, semi-crystalline, elastic, Kelvin–Voigt solids. Our results suggest that sequence grammars, which refer to amino acid identities of stickers versus spacers in prion-like low-complexity domains, have evolved to afford control over metastabilities of dominantly viscous fluid phases of condensates. This selection is likely to render barriers for conversion from metastable fluids to globally stable solids insurmountable on functionally relevant timescales. The time-dependent viscoelastic moduli of biomolecular condensates are connected to the functions that the condensates influence in cells. Now sticker and spacer residues in proteins are shown to regulate condensate viscoelasticity and ageing dynamics.

Bituminous binders as organic materials are prone to aging mainly by oxidation. Aging changes the viscoelastic behavior of the material over time towards higher stiffness and brittleness. FTIR has been increasingly used lately to investigate impacts of oxidative aging on the chemical structure of bitumen. Especially the carbonyl and sulfoxide bands are affected by aging and commonly used to describe changes due to evolving oxidation of a binder. However, spectra obtained from FTIR can be analyzed in fundamentally different ways and the analysis method applied to a spectrum has an impact on the gathered results and especially on the repeatability and sensitivity with regards to oxidative changes. For the presented study, two bituminous binders, a PG 64-16 and an SBS modified PG 76-22 PM were aged by RTFO and PAV and subsequently measured by FTIR. The obtained spectra (up to 90 individual spectra per aging state) were analyzed employing various methods using either the original or a normalized spectrum, a band maximum or integration based calculation of indices from an absolute or tangential baseline. By analyzing the coefficient of variation of the different analysis methods, it was found that not all analysis methods exhibit the same repeatability and sensitivity. From the findings of the study it can be recommended to work with normalized spectra, use an absolute baseline and work with integration of areas for index production in favor over band maximum based methods.

NRC publication: Yes

Many high-concentration multiphase materials that are industrially and academically important do not reach thermodynamic equilibrium because of kinetic constraints originating from the structurally arrested microstructure. However, owing to thermal or elastic energy of the constituents, their microstructure progressively reorganizes to form thermodynamically more stable states. In this physical ageing process, the whole spectrum of relaxation times evolves that makes relaxation dynamics increasingly sluggish. In a process of rejuvenation, deformation field increases mobility, but non-trivially alters the shape of relaxation time spectrum. Interestingly, this class of materials also demonstrates yield stress, whose origin could be closely related to physical aging, and as a result, it depends on time and deformation history. In this review, we present an overview of experimental behaviors and theoretical advances that indicate a complex coupling between ageing and rejuvenation for this class of materials having diverse microstructures.

The ageing behaviour of dense suspensions or pastes at rest is almost exclusively attributed to structural dynamics. Here, we identify another ageing process, contact-controlled ageing, consisting of the progressive stiffening of solid–solid contacts of an arrested colloidal suspension. By combining rheometry, confocal microscopy and particle-scale mechanical tests using laser tweezers, we demonstrate that this process governs the shear-modulus ageing of dense aqueous silica and polymer latex suspensions at moderate ionic strengths. We further show that contact-controlled ageing becomes relevant as soon as Coulombic interactions are sufficiently screened out that the formation of solid–solid contacts is not limited by activation barriers. Given that this condition only requires moderate ion concentrations, contact-controlled ageing should be generic in a wide class of materials, such as cements, soils or three-dimensional inks, thus questioning our understanding of ageing dynamics in these systems. The progressive stiffening of the solid–solid contacts that freeze dense colloidal suspensions are shown to cause the macroscopic ageing of such materials.