Explore the vast range of titles available.

A good knowledge of the quality of the satellite soil moisture products is of great importance for their application and improvement. This paper examines the performance of eight satellite-based soil moisture products, including the Soil Moisture Active Passive (SMAP) passive Level 3 (L3), the Soil Moisture and Ocean Salinity (SMOS) Centre Aval de Traitement des Données SMOS (CATDS) L3, the Japan Aerospace Exploration Agency (JAXA) Advanced Microwave Scanning Radiometer 2 (AMSR2) L3, the Land Parameter Retrieval Model (LPRM) AMSR2 L3, the European Space Agency (ESA) Climate Change Initiative (CCI) L3, the Chinese Fengyun-3B (FY3B) L2 soil moisture products at a coarse resolution of ~0.25°, and the newly released SMAP enhanced passive L3 and JAXA AMSR2 L3 soil moisture products at a medium resolution of ~0.1°. The ground soil moisture used for validation were collected from two well-calibrated and dense networks, including the Little Washita Watershed (LWW) network in the United States and the REMEDHUS network in Spain, each with different land cover. The results show that the SMAP passive soil moisture product outperformed the other products in the LWW network region, with an unbiased root mean square (ubRMSE) of 0.027 m3 m−3, whereas the FY3B soil moisture performed the best in the REMEDHUS network region, with an ubRMSE of 0.025 m3 m−3. The JAXA product performed much better at 0.25° than at 0.1°, but at both resolutions it underestimated soil moisture most of the time (bias < −0.05 m3 m−3). The SMAP-enhanced passive soil moisture product captured the temporal variation of ground measurements well, with a correlation coefficient larger than 0.8, and was generally superior to the JAXA product. The LPRM showed much larger amplitude and temporal variation than the ground soil moisture, with a wet bias larger than 0.09 m3 m−3. The underestimation of surface temperature may have contributed to the general dry bias found in the SMAP (−0.018 m3 m−3 for LWW and 0.016 m3 m−3 for REMEDHUS) and SMOS (−0.004 m3 m−3 for LWW and −0.012 m3 m−3 for REMEDHUS) soil moisture products. The ESA CCI product showed satisfactory performance with acceptable error metrics (ubRMSE < 0.045 m3 m−3), revealing the effectiveness of merging active and passive soil moisture products. The good performance of SMAP and FY3B demonstrates the potential in integrating them into the existing long-term ESA CCI product, in order to form a more reliable and useful product.

High-quality and long time-series soil moisture (SM) data are increasingly required for the Qinghai-Tibet Plateau (QTP) to more accurately and effectively assess climate change. In this study, to evaluate the accuracy and effectiveness of SM data, five passive microwave remotely sensed SM products are collected over the QTP, including those from the soil moisture active passive (SMAP), soil moisture and ocean salinity INRA-CESBIO (SMOS-IC), Fengyun-3B microwave radiation image (FY3B), and two SM products derived from the advanced microwave scanning radiometer 2 (AMSR2). The two AMSR2 products are generated by the land parameter retrieval model (LPRM) and the Japan Aerospace Exploration Agency (JAXA) algorithm, respectively. The SM products are evaluated through a two-stage data comparison method. The first stage is direct validation at the grid scale. Five SM products are compared with corresponding in situ measurements at five in situ networks, including Heihe, Naqu, Pali, Maqu, and Ngari. Another stage is indirect validation at the regional scale, where the uncertainties of the data are quantified by using a three-cornered hat (TCH) method. The results at the regional scale indicate that soil moisture is underestimated by JAXA and overestimated by LPRM, some noise is contained in temporal variations in SMOS-IC, and FY3B has relatively low absolute accuracy. The uncertainty of SMAP is the lowest among the five products over the entire QTP. In the SM map composed by five SM products with the lowest pixel-level uncertainty, 66.64% of the area is covered by SMAP (JAXA: 19.39%, FY3B: 10.83%, LPRM: 2.11%, and SMOS-IC: 1.03%). This study reveals some of the reasons for the different performances of these five SM products, mainly from the perspective of the parameterization schemes of their corresponding retrieval algorithms. Specifically, the parameterization configurations and corresponding input datasets, including the land-surface temperature, the vegetation optical depth, and the soil dielectric mixing model are analyzed and discussed. This study provides quantitative evidence to better understand the uncertainties of SM products and explain errors that originate from the retrieval algorithms.

The primary objective of this work is to develop an operational snow depth retrieval algorithm for the FengYun3B Microwave Radiation Imager（FY3B-MWRI） in China. Based on 7-year（2002–2009） observations of brightness temperature by the Advanced Microwave Scanning Radiometer-EOS（AMSR-E） and snow depth from Chinese meteorological stations, we develop a semi-empirical snow depth retrieval algorithm. When its land cover fraction is larger than 85%, we regard a pixel as pure at the satellite passive microwave remote-sensing scale. A 1-km resolution land use/land cover（LULC） map from the Data Center for Resources and Environmental Sciences, Chinese Academy of Sciences, is used to determine fractions of four main land cover types（grass, farmland, bare soil, and forest）. Land cover sensitivity snow depth retrieval algorithms are initially developed using AMSR-E brightness temperature data. Each grid-cell snow depth was estimated as the sum of snow depths from each land cover algorithm weighted by percentages of land cover types within each grid cell. Through evaluation of this algorithm using station measurements from 2006, the root mean square error（RMSE） of snow depth retrieval is about 5.6 cm. In forest regions, snow depth is underestimated relative to ground observation, because stem volume and canopy closure are ignored in current algorithms. In addition, comparison between snow cover derived from AMSR-E and FY3B-MWRI with Moderate-resolution Imaging Spectroradiometer（MODIS） snow cover products（MYD10C1） in January 2010 showed that algorithm accuracy in snow cover monitoring can reach 84%. Finally, we compared snow water equivalence（SWE） derived using FY3B-MWRI with AMSR-E SWE products in the Northern Hemisphere. The results show that AMSR-E overestimated SWE in China, which agrees with other validations.

Given their high albedo and low thermal conductivity, snow and sea ice are considered key reasons for amplified warming in the Arctic. Snow-covered sea ice is a more effective insulator, which greatly limits the energy and momentum exchange between the atmosphere and surface, and further controls the thermal dynamic processes of snow and ice. In this study, using the Microwave Emission Model of Layered Snowpacks (MEMLS), the sensitivities of the brightness temperatures (TBs) from the FengYun-3B/MicroWave Radiometer Imager (FY3B/MWRI) to changes in snow depth were simulated, on both first-year and multiyear ice in the Arctic. Further, the correlation coefficients between the TBs and snow depths in different atmospheric and sea ice environments were investigated. Based on the simulation results, the most sensitive factors to snow depth, including channels of MWRI and their combination form, were determined for snow depth retrieval. Finally, using the 2012–2013 Operational IceBridge (OIB) snow depth data, retrieval algorithms of snow depth were developed for the Arctic on first-year and multiyear ice, separately. Validation using the 2011 OIB data indicates that the bias and standard deviation (Std) of the algorithm are 2.89 cm and 2.6 cm on first-year ice (FYI), respectively, and 1.44 cm and 4.53 cm on multiyear ice (MYI), respectively.

Soil moisture (SM) is a crucial driving variable for the global land surface-atmosphere water and energy cycle. There are now many satellite-based SM products available internationally and it is necessary to consider all available SM products under the same context for comprehensive assessment and inter-comparisons at the global scale. Moreover, product performances varying with dynamic environmental factors, especially those closely related to retrieval algorithms, were less investigated. Therefore, this study evaluated and identified the relative strengths of nine mainstream satellite-based SM products derived from the Advanced Microwave Scanning Radiometer 2 (AMSR2), Chinese Fengyun-3B (FY3B), the Soil Moisture Active Passive (SMAP), the Soil Moisture and Ocean Salinity (SMOS), and the European Space Agency (ESA) Climate Change Initiative (CCI) by using the Pearson correlation coefficient (R), R of SM seasonal anomalies (Ranom), unbiased Root Mean Square Error (ubRMSE), and bias metrics against ground observations from the International Soil Moisture Network (ISMN), as well as the Global Land Data Assimilation System (GLDAS) Noah model simulations, overall and under three dynamic (Land Surface Temperature (LST), SM, and Vegetation Optical Depth (VOD)) conditions. Results showed that the SMOS-INRA-CESBIO (IC) product outperformed the SMOSL3 product in most cases, especially in Australia, but it exhibited greater variability and higher random errors in Asia. ESA CCI products outperformed other products in capturing the spatial dynamics of SM seasonal anomalies and produced significantly high accuracy in croplands. Although the Chinese FY3B presented poor skills in most cases, it had a good ability to capture the temporal dynamics of the original SM and SM seasonal anomalies in most regions of central Africa. Under various land cover types, with the changes in LST, SM, and VOD, different products exhibited distinctly dynamic error characteristics. Generally, all products tended to overestimate the low in-situ SM content but underestimate the high in-situ SM content. It is expected that these findings can provide guidance and references for product improvement and application promotions in water exchange and land surface energy cycle.

An in situ soil moisture observation network at pixel scale is constructed in cropland in the northeast of China for accurate regional soil moisture evaluations of satellite products. The soil moisture products are based on the Japan Aerospace Exploration Agency (JAXA) algorithm and the Land Parameter Retrieval Model (LPRM) from the Advanced Microwave Scanning Radiometer 2 (AMSR2), and the products from the FengYun-3B (FY3B) satellite are evaluated using synchronous in situ data collected by the EC-5 sensors at the surface in a typical cropland in the northeast of China during the crop-growing season from May to September 2017. The results show that the JAXA product provides an underestimation with a bias (b) of -0.094 cm3/cm3, and the LPRM soil moisture product generates an overestimation with a b of 0.156 cm3/cm3. However the LPRM product shows a better correlation with the in situ data, especially in the early experimental period when the correlation coefficient is 0.654, which means only the JAXA product in the early stage, with an unbiased root mean square error (ubRMSE) of 0.049 cm3/cm3 and a b of -0.043 cm3/cm3, reaches the goal accuracy (±0.05 cm3/cm3). The FY3B has consistently obtained microwave brightness temperature data, but its soil moisture product data in the study area is seriously missing during most of the experimental period. However, it recovers in the later period and is closer to the in situ data than the JAXA and LPRM products. The three products show totally different trends with vegetation cover, soil temperature, and actual soil moisture itself in different time periods. The LPRM product is more sensitive and correlated with the in situ data, and is less susceptible to interferences. The JAXA is numerically closer to the in situ data, but the results are still affected by temperature. Both will decrease in accuracy as the actual soil moisture increases. The FY3B seems to perform better at the end of the whole period after data recovery.

Soil moisture (SM) is a key variable in hydrological processes, bio-ecological processes, and biogeochemical processes. Long-term observations of soil moisture over large areas are critical to research on flooding and drought monitoring, water resource management, and crop yield forecasts. In this paper, Fengyun (FY3B and FY3C) SM products, Japan Aerospace Exploration Agency (JAXA) SM products from the Advanced Microwave Scanning Radiometer 2 (AMSR2), the Land Parameter Retrieval Model (LPRM) AMSR2 L3 SM products, the Version 2 (v2) global land parameter data record (LPDR) of SM products, Soil Moisture Ocean Salinity (SMOS) Centre Aval de Traitement des Données SMOS (CATDS) L3 SM products, the Soil Moisture Active Passive (SMAP) passive L3 SM products and the European Space Agency(ESA) Climate Change Initiative (CCI) SM products were evaluated using the ground-based observations in the Little Washita, Fort Cobb and Yanco networks. Long-time series comparison between measured and satellite products was conducted to evaluate the overall performance of FY3 series satellites SM products. Bias (mean bias), R (correlation coefficient), RMSE (root mean square error) and ubRMSE (unbiased root mean square error) were calculated to explore the agreement between satellite products and in-situ measurements. Taylor diagrams were used to compare the performance of various satellite products. The result showed that (1) FY3B, FY3C and LPRM AMSR2 ascending and descending products had an obvious overestimate with in-situ soil moisture in three networks. (2) JAXA AMSR2 ascending and descending products had considerable underestimation in three networks. (3) The validation result of SMOS ascending and descending products over the three networks was satisfactory, with a rather high correlation than other X-band products. (4) The validation result of SMAP ascending and descending products outperformed the other products over the Little Washita and Fort Cobb networks. (5) The ESA CCI product had the lowest values of RMSE and ubRMSE than the other products in the Yanco network, revealing the effectiveness of merging active and passive soil moisture products. (6)The LPDR descending SM products had better performance than the LPDR ascending SM products in the LW and FC networks.

As an important factor in the stability of the climate system in the northern hemisphere, the Arctic has recently attracted considerable attention. In the Arctic, most sea ice is covered by snow year-round, except in the snow-melting season. Given its high albedo and low thermal conductivity, snow cover on sea ice is considered a key component of amplified warming in the Arctic. However, in Arctic regions, the only products available are for snow depths on first-year ice. Therefore, this paper studies the temporal and spatial changes of snow depth on first-year ice in the Arctic using the snow depth on sea ice product determined from the Microwave Radiation Imager onboard the Feng Yun-3B satellite. We averaged the daily snow depth on first-year ice data to give monthly and annual values over the period 2011–2018, using flags for multiyear ice and melting points. Taking the 2012 data as an example, the analysis results show that the spatial distribution of snow depth in the monthly and annual data is similar over the whole first-year ice area. The snow depth basically decreases with latitude, and the distribution features exhibit little variation by month and year. The weekly mean snow depth on first-year ice begins to increase from October/November due to snowfall, and reaches a maximum value in late April/early May of the next year. There is no obvious law governing the inter-annual variation of snow depth in the Arctic from 2011–2018.

temperatures. Given the high albedo and low thermal conductivity, snow is regarded as one of the key reasons for the amplification of the warming in polar regions. The distributions of sea ice and snow depth are essential to the whole thermal conduction in the Arctic. This study focused on the retrieval of snow depth on sea ice from brightness temperatures of the MicroWave Radiometer Imager (MWRI) onboard the FengYun (FY)-3B satellite during the period from December 1, 2010 to April 30, 2011. After cross calibrated to the Advanced Microwave Scanning Radiometer–EOS (AMSR-E) Level 2A data, the MWRI brightness temperatures were applied to calculate the sea ice concentrations based on the Arctic Radiation and Turbulence Interaction Study Sea Ice (ASI) algorithm. According to the proportional relationship between the snow depth and the surface scattering in 18.7 and 36.5 GHz, the snow depths were derived. In order to eliminate the influence of uncertainties in grain sizes of snow as well as sporadic weather effects, the seven-day averaged snow depths were calculated. Then the results were compared with the snow depths from the AMSR-E Level 3 Sea Ice products. The bias of differences between the MWRI and the AMSR-E Level 3 products are ranged between −1.09 and −0.32 cm，while the standard deviations and the correlation coefficients are ranged from 2.47 to 2.88 cm and from 0.78 to 0.90 for different months. As a result, it could be summarized that FY3B/MWRI showed a promising prospect in retrieving snow depth on sea ice.