Explore the vast range of titles available.

Consolidates the many different chemistries being employed to provide environmentally acceptable products through the upstream oil and gas industry.-- Provided by publisher.

To address the issues of low frequency and high costs associated with the current manual production measurement for ESP wells in the Tarim Oilfield, a study was conducted to develop a digital production measurement method for ESP wells. Based on the principle of energy conservation, where the input power of the pump equals the output power of the motor, and incorporating parameters such as surface tubing and casing pressure, motor current, and motor/ pump performance curves, with viscosity correction of the pump performance curve, a corrected power calculation method was proposed. A digital production measurement mathematical model was established. According to feedback from field applications, the calculated results of this method align well with the metered results when corrected using on-site measured flow rate. Furthermore, by applying this model, accurate allocation of merged production well outputs and risk warning or failure diagnosis for oil wells can be achieved. This method not only improves the accuracy and efficiency of ESP well production calculations but also enables real-time reflection of oil well production trends, contributing to intelligent production management in the Tarim Oilfield and significantly enhancing the level of oilfield production management.

This research focused on the quantitative assessment of the surface deformation velocities and rates and their natural and man-made controlling factors at Tengiz Oilfield in Kazakhstan using the Small Baseline Subset remote sensing technique followed by 3D and 2D decompositions and cosine corrections to derive vertical and horizontal movements from line-of-sight (LOS) measurements. In the present research we applied time-series of Sentinel-1 satellite images acquired during 2018–2020. All ground deformation derivatives showed the continuous subsidence at the Tengiz oilfield with increasing velocity. 3D and 2D decompositions of LOS measurements to vertical movement showed that the Tengiz Oil Field 2018–2020 continuously subsided with the maximum annual vertical deformation velocity around 70 mm. Based on the LOS measurements, the maximum annual subsiding velocity was observed to be 60 mm. Cosine corrections of LOS measurements to vertical movement, however, revealed a maximum annual vertical deformation velocity of 77 mm. The vertical deformation confirmed typical patterns of subsidence caused by oil extraction. Detected east-west and north-south horizontal movements at the Tengiz field clearly indicated that the study area crossed by seismic faults is affected by natural tectonic processes. The overall RMSE of 3D decomposed vertical deformation in relationship to LOS measurements and cosine corrections were in the range of 10–13 mm and 6–8 mm, correspondingly. The results of the present research will support operators of oil and gas fields and also other types of infrastructure to evaluate the actual differences of InSAR ground deformation measurements against the required standards and the precision of measurements depending on the operational needs, timeframes and availability of radar imagery.

The Sichuan Basin is rich in shale oil and gas resources, with favorable geological conditions that the other shale reservoirs in China cannot match. Thus, the basin is an ideal option for fully “exploring petroleum inside source kitchen” with respect to onshore shale oil and gas in China. This paper analyzes the characteristics of shale oil and gas resources in the United States and China, and points out that maturity plays an important role in controlling shale oil and gas composition. US shale oil and gas exhibit high proportions of light hydrocarbon and wet gas, whereas Chinese marine and transitional shale gas is mainly dry gas and continental shale oil is generally heavy. A comprehensive geological study of shale oil and gas in the Sichuan Basin reveals findings with respect to the following three aspects. First, there are multiple sets of organic-rich shale reservoirs of three types in the basin, such as the Cambrian Qiongzhusi Formation and Ordovician Wufeng Formation-Silurian Longmaxi Formation marine shale, Permian Longtan Formation transitional shale, Triassic Xujiahe Formation lake-swamp shale, and Jurassic lacustrine shale. Marine shale gas enrichment is mainly controlled by four elements: Deep-water shelf facies, moderate thermal evolution, calcium-rich and silicon-rich rock association, and closed roof/floor. Second, the “sweet section” is generally characterized by high total organic carbon, high gas content, large porosity, high brittle minerals content, high formation pressure, and the presence of lamellation/bedding and natural microfractures. Moreover, the “sweet area” is generally characterized by very thick organic-rich shale, moderate thermal evolution, good preservation conditions, and shallow burial depth, which are exemplified by the shale oil and gas in the Wufeng-Longmaxi Formation, Longtan Formation, and Daanzhai Member of the Ziliujing Formation. Third, the marine, transitional, and continental shale oil and gas resources in the Sichuan Basin account for 50%, 25%, and 30% of the respective types of shale oil and gas geological resources in China, with great potential to become the cradle of the shale oil and gas industrial revolution in China. Following the “Conventional Daqing-Oil” (i.e., the Daqing oilfield in the Songliao Basin) and the “Western Daqing-Oil & Gas” (i.e., the Changqing oilfield in the Ordos Basin), the Southwest oil and gas field in the Sichuan Basin is expected to be built into a “Sichuan-Chongqing Daqing-Gas” in China.

In recent years, petroleum exploration in the Carboniferous volcanic rock reservoirs in the Junggar Basin has been the focus of important petroleum energy development in western China. The lithologic identification of volcanic rock reservoirs seriously restricts the accuracy of reservoir prediction and affects the success rate of oil exploration. Different types of volcanic rocks have different petrological characteristics and mineral assemblages, especially affected by the depositional environment. The volcanic rocks in different regions have their own uniqueness. This paper takes the Carboniferous volcanic reservoirs in Xiquan block, Beisantai Oilfield, Junggar Basin as the research target. Through a large number of core observations, casting slices, scanning electron microscopy, and X-ray diffraction methods, the Carboniferous volcanic rocks are analyzed. The petrology, pore characteristics, physical properties, and diagenetic evolution history of the reservoir are analyzed. The study shows that the volcanic facies in the Xiquan block can be divided into explosive facies, overflow facies, and volcanic sedimentary facies, among which the explosive facies is subdivided into empty subfacies (volcanic breccia-breccia tuff combination) and thermal base wave subfacies (tuff). The lithology of the reservoir is pyroclastic rock and volcanic lava, belonging to medium-porous and ultralow permeability reservoirs, and the storage space can be divided into three types: primary pores, secondary pores, and fractures. The lithology of key exploration is breccia tuff, followed by breccia tuff and volcanic breccia.

Well activation is one of the most important aspects in the oil and gas industries and nitrogen gas is predominately used. The gas, being light, is sent down the producing reservoir which will enhance the production or improve the flow of crude oil. In addition to the methods used to increase production there are several problems like sand production and water production from the producing wells.Sand production occurs when the destabilizing stresses at the formation face exceed the strength of the natural arching tendencies and/or grain-to-grain cementation strength. Ideally, during oil production, the formation should be porous, permeable and well consolidated through which hydrocarbons can easily flow into the production wells. But sometimes, especially during production from unconsolidated sandstone reservoirs, the produced hydrocarbons may also carry large amounts of sand into the well bore and sand entering production wells is one of the oldest problems faced by oil companies and one of the toughest to solve. These unconsolidated formations may not restrain grain movement, and produce sand along with the fluids especially at high rates.Water production is also a problem that many reservoir or production engineers face in day-to-day life. As engineers we should be able to decide whether water control solutions should be applied or not. The excess production of water is caused by the depletion of the reservoir and simply sweeps away most of the oil that the reservoir can produce.This book gives an information how well activation using nitrogen is carried out, and how sand control and water control issues can be resolved.

This book bridges the gap between theory and practice in a range of real-world EOR settings. Areas covered include steam and polymer flooding, use of foam, in situ combustion, microorganisms, \"smart water\"-based EOR in carbonates and sandstones, and many more. Oil industry professionals know that the key to a successful enhanced oil recovery project lies in anticipating the differences between plans and the realities found in the field. This book aids that effort, providing valuable case studies from more than 250 EOR pilot and field applications in a variety of oil fields. The case studies cover practical problems, underlying theoretical and modeling methods, operational parameters, solutions and sensitivity studies, and performance optimization strategies, benefitting academicians and oil company practitioners alike.

Emulsification plays an important role in enhancing oil recovery. Experiments and field applications of alkali/surfactant/polymer (ASP) flooding indicated that the amount of oil recovery in liquids with emulsions is 5% higher than that in liquids with no emulsions. Therefore, it is of great significance to study emulsion and its field application for enhanced oil recovery. This paper discusses the current status of emulsion for enhanced oil recovery, including the formation mechanism of emulsions in chemical flooding, rheological properties, stability, seepage characteristics, emulsion improving sweep volume, and displacement efficiency, along with future development plans of emulsion for enhanced oil recovery, especially surfactants for chemical flooding. In addition, the Pickering emulsion for application in enhanced oil recovery is also discussed. The development effects of emulsion flooding have been discussed for the Midway‐Sunset Oilfield, the emulsification characteristics of ASP flooding have been analyzed in Xing‐V and Xing‐II of the Daqing Oilfield, and the experiences regarding emulsion for enhanced oil recovery have been summarized. The key research directions of emulsion for enhanced oil recovery are indicated. Emulsification plays an important role in enhancing oil recovery. Although there have been developments, some fundamental aspects of emulsion seepage and the mechanism of emulsion enhancing oil recovery remain unclear. The emulsion formation mechanism, rheological properties, stability, seepage characteristics, and enhanced oil recovery are discussed in detail. The application of emulsion for enhanced oil recovery is analyzed, and the experiences from laboratory tests and field tests are summarized.

Oilfield produced water (OPW) has become a primary environmental concern due to the high concentration of dissolved organic pollutants that lead to bioaccumulation with high toxicity, resistance to biodegradation, carcinogenicity, and the inhibition of reproduction, endocrine, and non-endocrine systems in aquatic biota. Photodegradation using photocatalysts has been considered as a promising technology to sustainably resolve OPW pollutants due to its benefits, including not requiring additional chemicals and producing a harmless compound as the result of pollutant photodegradation. Currently, titanium dioxide (TiO2) has gained great attention as a promising photocatalyst due to its beneficial properties among the other photocatalysts, such as excellent optical and electronic properties, high chemical stability, low cost, non-toxicity, and eco-friendliness. However, the photoactivity of TiO2 is still inhibited because it has a wide band gap and a low quantum field. Hence, the modification approaches for TiO2 can improve its properties in terms of the photocatalytic ability, which would likely boost the charge carrier transfer, prevent the recombination of electrons and holes, and enhance the visible light response. In this review, we provide an overview of several routes for modifying TiO2. The as-improved photocatalytic performance of the modified TiO2 with regard to OPW treatment is reviewed. The stability of modified TiO2 was also studied. The future perspective and challenges in developing the modification of TiO2-based photocatalysts are explained.

This paper provides an introduction to the topic of water shutoff and conformance improvement. After indicating the volumes of water produced during oilfield operations, a strategy is provided for attacking excess water production problems. Problem types are categorized, typical methods of problem diagnosis are mentioned, and the range of solutions is introduced for each problem type. In the third section of the paper, the concept of disproportionate permeability reduction is introduced—where polymers and gels may reduce permeability to water more than to oil or gas. When and where this property is of value is discussed. The fourth section describes the properties of formed gels as they extrude through fractures and how those properties can be of value when treating conformance problems caused by fractures. Section 5 covers the efficiency with which gels block fractures after gel placement—especially, the impact of fluids injected subsequent to the gel treatment.