Explore the vast range of titles available.

Sometimes, during the dyeing process of textile fabrics, some color variations and color spots occur, which considerably decrease the fabric quality. The problem of defective and uneven dyeing during textile processing generally involves a chemical stripping approach. The stripping efficiency of reactive dyes from cellulose fabric cannot be easily attained because of the formation of covalent bonds between dye molecules and fibers. This research examined the effects of oxidative and reductive color stripping on cotton fabrics dyed with reactive black 5 dye. A microwave-assisted technique was applied instead of conventional stripping methods, which involve chemicals and high energy consumption that adversely affect the strength and quality of the fabric. This strategy ensures efficient surface strength and fabric quality, which is favorable for redyeing. The efficiency of the stripped material was 97–97.56%, as measured via a Spectra-flash spectrophotometer, and the fabric strength was determined when the fabric was subjected to the primary method, i.e., 306 was the load at a maximum elongation percentage of 11.16% according to the tensile strength of the material. The data obtained from this study were evaluated via a standard deviation method.

Purpose: To compare the outcomes of two techniques, for preparation of microkeratome-assisted ultrathin grafts for Descemet's stripping automated endothelial keratoplasty (DSAEK). Methods: The study involved 20 eyes of 20 patients with pseudophakic bullous keratopathy, randomized into two groups. Group 1 eyes underwent microkeratome-assisted DSAEK using the single-pass technique for lenticule preparation, whereas group 2 eyes underwent microkeratome-assisted DSAEK using the double-pass technique. Patients were followed up till 6 months, postoperatively. Best-corrected visual acuity (BCVA) at final follow-up was considered as the primary outcome measure, whereas graft thickness (GT) contrast sensitivity and endothelial cell loss were considered as the secondary outcome measures. A P value of <0.05 was considered as statistically significant. Results: Baseline characteristics of two groups were comparable. The mean central GT was comparable in both groups at 6 months follow-up [group 1: 98 ± 24.46 μm, group 2: 129 ± 31.46 μm (P = 0.18)]. Both groups fared equally in terms of BCVA (P = 0.33). Contrast sensitivity was significantly better in group 1 eyes (P = 0.045). A statistically significant negative correlation was found between postoperative BCVA and postoperative GT (R = −0.728, P = 0.016). The percentage endothelial cell loss was slightly higher in group 2 eyes, although not statistically significant. Two eyes in group 2 experienced complications during lenticule preparation. None of the eye experienced any complication in the postoperative period. Conclusion: Both techniques provided grafts with comparable thickness and endothelial cell loss and were associated with comparable BCVA, at final follow-up visit. The contrast sensitivity was, however, better in eyes receiving grafts prepared with the single-pass technique.

Background and Objectives: Descemet stripping automated endothelial keratoplasty (DSAEK) is a widely used surgical technique for treating corneal endothelial dysfunctions such as Fuchs endothelial corneal dystrophy (FECD) and pseudophakic bullous keratopathy (PBK). This study aimed to investigate the association between postoperative visual acuity and various corneal morphological and optical parameters, including corneal densitometry (CD) and higher-order aberrations (HOAs), measured using the Pentacam (OCULUS Optikgeräte GmbH, Wetzlar, Germany), as well as graft thickness, which was assessed by anterior segment optic coherence tomography (AS-OCT), (Optovue Inc., Fremont, CA, USA), and corneal thickness, assessed by both AS-OCT and Pentacam. Materials and Methods: This prospective, observational cohort study included 17 eyes from 13 patients who underwent DSAEK. Data on preoperative visual acuity were collected, while postoperative parameters were assessed during follow-up visits. Corneal measurements included the total corneal and corneal graft thickness, corneal densitometry in 20 defined subregions, and corneal higher-order aberrations. Associations between these parameters and postoperative visual acuity were evaluated using nonparametric statistical tests. Results: The postoperative visual acuity improved significantly (p < 0.001). Strong correlations were found between poorer visual acuity and higher CD values. The strongest correlations with visual acuity were found for CD 2–6 mm total (Rho = 0.795; p < 0.001), CD central 2–6 mm (Rho = 0.791; p < 0.001), and CD central 0–2 mm (Rho = 0.730; p < 0.001). Significant associations were also observed with anterior and posterior HOAs (Rho = 0.624, p = 0.01; and Rho = 0.556, p = 0.02, respectively). No correlation was found between visual outcomes and graft thickness measured by AS-OCT (Rho = 0.051; p = 0.85), nor with total corneal thickness measured by AS-OCT (Rho = −0.227; p = 0.38) or Pentacam (Rho = −0.369; p = 0.14). Conclusions: This study demonstrates that CD and HOAs are more strongly associated with postoperative visual acuity after DSAEK than traditionally monitored parameters such as graft or corneal thickness. The results highlight the value of detailed corneal imaging and support the use of advanced optical diagnostics in postoperative evaluation.

This study analyzed the influence of different ammonia stripping parameters on ammonia removal efficiency and mass transfer rate. Ammonia stripping was performed on two devices, a column and a packed tower, with artificial ammonium hydroxide wastewater. First, ammonia concentration and pH were varied in a column without liquid circulation. At the same pH, the removal efficiency and mass transfer rate were constant, irrespective of initial ammonia concentration. When pH was increased, the ammonia fraction also increased, resulting in higher removal efficiency and mass transfer rate. Second, the effects of stripping were assessed using a packed tower with fluid circulation. The ammonium hydroxide concentration did not affect the removal efficiency or mass transfer rate. Furthermore, at apparatus liquid-gas ratios of 26.8–107.2 L/m3, a lower liquid-gas ratio led to increased ammonia removal efficiency and mass transfer rate. Conversely, the lower the liquid-gas ratio, the greater the air consumption. In conclusion, considering the removal rate and volume of air supply, the range of optimal liquid-gas ratio was determined as 26.8–53.6 L/m3. In particular, the 26.8 L/m3 condition achieved the best ammonia removal rate of 63.0% through only 6 h of stripping at 70 °C and pH 8.5.

AimsTo compare best-corrected visual acuity (BCVA), contrast sensitivity and endothelial cell density (ECD) after ultrathin Descemet’s stripping automated endothelial keratoplasty (UT-DSAEK) and Descemet’s membrane endothelial keratoplasty (DMEK).MethodsA randomised, single-blinded, single-centre design was used. 72 patients with Fuchs’ endothelial dystrophy and cataract were randomised to UT-DSAEK or DMEK combined with phacoemulsification and lens implantation. 27 patients with cataract were included in a control group and treated with phacoemulsification and lens implantation. The primary outcome was BCVA at 12 months.ResultsCompared with UT-DSAEK, DMEK resulted in better BCVA with mean differences of 6.1 early treatment diabetic retinopathy study (ETDRS) (p=0.001) after 3 months, 7.4 ETDRS (p<0.001) after 6 months and 5.7 ETDRS (p<0.001) after 12 months. The control group obtained significantly better BCVA with a mean difference of 5.2 ETDRS (p<0.001) compared with DMEK 12 months postoperatively. Compared with UT-DSAEK, contrast sensitivity was significantly better 3 months after DMEK with a mean difference of 0.10 LogCS (p=0.03). However, our study found no effect after 12 months (p=0.08). ECD was significantly lower after UT-DSAEK compared with DMEK with mean differences of 332 cells/mm2 (p<0.01) after 3 months, 296 cells/mm2 (p<0.01) after 6 months and 227 cells/mm2 (p=0.03) after 12 months.ConclusionsCompared with UT-DSAEK, DMEK resulted in better BCVA 3, 6 and 12 months postoperatively. Twelve months postoperatively, DMEK had a higher ECD than UT-DSAEK; however, no difference in contrast sensitivity was found.Trial registration number NCT04417959

The formation of lithium dendrites during charge-discharge cycles limits the development of lithium metal batteries, because the dendrites can cause electrical shorting of the cells. A number of tricks have been used to try to prevent dendrite formation. Li et al. took the opposite approach (see the Perspective by Mukhopadhyay and Jangid). They operated their cells at higher current densities, under which one would expect dendrites to form owing to the higher nucleation rates. However, under these conditions, the dendrites that started to form heated up and annealed, leading to their disappearance. Science , this issue p. 1513 ; see also p. 1463 Lithium metal dendrites can be healed in situ by Joule self-heating of the dendritic particles. Lithium (Li) metal electrodes are not deployable in rechargeable batteries because electrochemical plating and stripping invariably leads to growth of dendrites that reduce coulombic efficiency and eventually short the battery. It is generally accepted that the dendrite problem is exacerbated at high current densities. Here, we report a regime for dendrite evolution in which the reverse is true. In our experiments, we found that when the plating and stripping current density is raised above ~9 milliamperes per square centimeter, there is substantial self-heating of the dendrites, which triggers extensive surface migration of Li. This surface diffusion heals the dendrites and smoothens the Li metal surface. We show that repeated doses of high-current-density healing treatment enables the safe cycling of Li-sulfur batteries with high coulombic efficiency.

We aimed to investigate the clinical characteristics and risk factors for graft rejection after keratoplasty in Japanese patients. We enrolled 730 cases (566 patients) of penetrating keratoplasty (PK, N = 198), Descemet’s stripping automated endothelial keratoplasty (DSAEK, N = 277), non-Descemet’s stripping automated endothelial keratoplasty (nDSAEK, N = 138), and Descemet membrane endothelial keratoplasty (DMEK, N = 117). The incidence, clinical characteristics, and possible risk factors for graft rejection were analyzed. Graft rejection occurred in 65 cases (56 patients, 8.9%). The incidence rate of rejection was highest with PK (3.45/100 person-years), followed by DSAEK (2.34), nDSAEK (1.55), and DMEK (0.24). Cox regression analysis revealed keratoplasty type, younger age, indications (such as failed keratoplasty and infection), and steroid eyedrop use as possible risk factors. In the multivariate model adjusting baseline characteristics, PK and DSAEK had significantly higher hazard ratios (HRs) than DMEK (HR = 13.6, 95% confidence interval [CI] [1.83, 101] for PK, 7.77 [1.03, 58.6] for DSAEK). Although not statistically significant, the HR estimate of nDSAEK to DMEK (HR = 7.64, 95% CI [0.98, 59.6]) indicated higher HR in nDSAEK than in DMEK. DMEK is the favorable option among the four surgical procedures to avoid graft rejection after keratoplasty.

Metallic zinc is an attractive anode material for aqueous rechargeable batteries because of its high theoretical capacity and low cost. However, state-of-the-art zinc anodes suffer from low coulombic efficiency and severe dendrite growth during stripping/plating processes, hampering their practical applications. Here we show that eutectic-composition alloying of zinc and aluminum as an effective strategy substantially tackles these irreversibility issues by making use of their lamellar structure, composed of alternating zinc and aluminum nanolamellas. The lamellar nanostructure not only promotes zinc stripping from precursor eutectic Zn 88 Al 12 (at%) alloys, but produces core/shell aluminum/aluminum sesquioxide interlamellar nanopatterns in situ to in turn guide subsequent growth of zinc, enabling dendrite-free zinc stripping/plating for more than 2000 h in oxygen-absent aqueous electrolyte. These outstanding electrochemical properties enlist zinc-ion batteries constructed with Zn 88 Al 12 alloy anode and K x MnO 2 cathode to deliver high-density energy at high levels of electrical power and retain 100% capacity after 200 hours. Aqueous rechargeable Zn-ion batteries are attractive energy storage devices, but their wide adoption is impeded by the irreversible metallic Zn anode. Here the authors report lamellar-nanostructured eutectic Zn/Al alloys as reversible and dendrite-free anodes for improved battery performance.

This study aimed to report the 3-year clinical outcomes of corneal endothelial keratoplasty (EK) in late-stage elderly patients (≥75 years) compared with younger patients (<75 years). Retrospective observational study. Patients who underwent EK, including Descemet's stripping automated keratoplasty (DSAEK) and non-Descemet stripping and automated endothelial keratoplasty (nDSAEK) with bullous keratopathy (BK) at Keio University Hospital between 2016 and 2018, were included. Patient characteristics, graft survival rate, best corrected visual acuity (BCVA), corneal endothelial cell density (ECD), and complications were compared between the late elderly group (75 years or older) and the younger group (<75 years old) stratified by surgical procedure. Among the 64 eyes and 55 patients who underwent EK, 31 eyes and 30 patients were in the late elderly group (81.4±3.7 years), and 33 eyes and 25 patients were in the younger group (66.2±9.1 years). There was no difference between the groups in terms of the cause of BK, and PBK was more common in the DSAEK group in the late elderly group (p = 0.029). There was no difference in graft survival between the two groups during the follow-up period. In the late elderly group, graft survival was significantly better in the nDSAEK group than in the DSAEK group (p = 0.045). BCVA and postoperative ECD improved in both groups. There were no differences in intraoperative or postoperative complications between the late elderly and younger groups. EK for BK in late elderly patients resulted in postoperative visual improvement, with similar efficacy and safety to those of EK for BK in younger patients.

The article describes innovative procedures for determining In(III) using anodic stripping voltammetry (ASV) and adsorptive stripping voltammetry (AdSV) with cupferron as a chelating agent. In both procedures, an environmentally friendly solid bismuth microelectrode (SBiµE) with a diameter of 25 µm was used as the working electrode. In both procedures, 0.1 mol L−1 acetate buffer with a pH of 3.0 ± 0.05 was used as the supporting electrolyte. The electrochemical measurement conditions were as follows: −2.4 V for a 20 s activation step and −1.2 V for a 20 s accumulation step for ASV, and −2.5 V for a 45 s activation step and −0.65 V for a 10 s accumulation step for AdSV. The signal was recorded as a result of a positive potential change from −1.0 to −0.3 V in the case of the ASV procedure and as a result of a negative potential change from −0.4 to −1.0 V in the case of the AdSV procedure. The calibration graph was linear from 5 × 10−9 mol L−1 to 5 × 10−7 mol L−1 with a detection limit of 1.4 × 10−9 mol L−1 for ASV and from 1 × 10−9 mol L−1 to 1 × 10−7 mol L−1 with a detection limit of 3.9 × 10−10 mol L−1 for AdSV. The effect of interferents such as surfactants, humic substances and EDTA on the analytical signal was compared in the case of signal recording using the ASV technique with the signal recorded using the AdSV technique. Based on the results obtained, it was determined how the charge of interferents affects the signal depending on the technique used. To validate the practical application of the developed procedures, an analysis of In(III) recovery from samples of the Baltic Sea and Synthetic Sea Water was performed.