Explore the vast range of titles available.

This study focused on the preparation and investigation of g-C3N4/TiO2 photocatalysts using different TiO2 morphologies (anatase nanoparticles (TPs), poorly crystalline nanotubes (aTTs), and well-crystalline anatase nanorods (TRs)) and self-synthesized g-C3N4 (CN). The synthesis of the g-C3N4/TiO2 composites was carried out using a mortar mixing technique and a g-C3N4 to TiO2 weight ratio of 1:1. In addition, the g-C3N4/TiO2 composites were annealed in a muffle furnace at 350 °C for 2 h in air. The successful formation of a g-C3N4/TiO2 composite with a mesoporous structure was confirmed using the results of XRD, N2 physisorption, and FTIR analyses, while the results of microscopic analysis techniques confirmed the preservation of TiO2 morphology in all g-C3N4/TiO2 composites investigated. UV-Vis DR measurements showed that the investigated g-C3N4/TiO2 composites exhibited visible-light absorption due to the presence of CN. The results of solid-state photoluminescence and electrochemical impedance spectroscopy showed that the composites exhibited a lower charge recombination compared to pure TiO2 and CN. For example, the charge transfer resistance (RCT) of the CNTR/2 composite of TR and CN calcined in air for 2 h was significantly reduced to 0.4 MΩ, compared to 0.9 MΩ for pure TR and 1.0 MΩ for pure CN. The CNTR/2 composite showed the highest photocatalytic performance of the materials tested, achieving 30.3% degradation and 25.4% mineralization of bisphenol A (BPA) dissolved in water under visible-light illumination. In comparison, the pure TiO2 and CN components achieved significantly lower BPA degradation rates (between 2.4 and 11.4%) and mineralization levels (between 0.6 and 7.8%). This was due to (i) the presence of Ti3+ and O-vacancies in the TR, (ii) enhanced heterojunction formation, and (iii) charge transfer dynamics enabled by a dual mixed type-II/Z scheme mechanism.

Titanium dioxide (TiO2) is a semiconductor material that plays an important role in photocatalysis. Bicontinuous concentric lamellar (bcl) is an interesting morphology with an open channel pore structure that has been successfully synthesized on silica-based materials. If bcl morphology can be applied in TiO2 system, then many surface properties of TiO2 can be enhanced, i.e. photocatalytic activity. A simple and effective strategy has been demonstrated to transform aggregated and spherical TiO2 particles to bcl morphology via alkaline hydrothermal route. Alkaline hydrothermal treatment successfully transforms TiO2 particle surface to have bcl morphology through swelling with ammonia then followed by phase segregation process. We proposed this strategy as a general pathway to transform the particle surface with any shape to have bcl morphology. 

Legionella pneumophila (L. pneumophila) is the causative agent of Legionnaires’ disease and Pontiac fever, collectively known as legionellosis. L. pneumophila infection occurs through inhalation of contaminated aerosols from water systems in workplaces and institutions. The development of disinfectants that can eliminate L. pneumophila in such water systems without evacuating people is needed to prevent the spread of L. pneumophila. Photocatalysts are attractive disinfectants that do not harm human health. In particular, the TiO2 photocatalyst kills L. pneumophila under various conditions, but its mode of action is unknown. Here, we confirmed the high performance of TiO2 photocatalyst containing PtO2 via the degradation of methylene blue (half-value period: 19.2 min) and bactericidal activity against Escherichia coli (half-value period: 15.1 min) in water. Using transmission electron microscopy, we demonstrate that the disinfection of L. pneumophila (half-value period: 6.7 min) by TiO2 photocatalyst in water is accompanied by remarkable cellular membrane and internal damage to L. pneumophila. Assays with limulus amebocyte lysate and silver staining showed the release of endotoxin from L. pneumophila due to membrane damage and photocatalytic degradation of this endotoxin. This is the first study to demonstrate the disinfection mechanisms of TiO2 photocatalyst, namely, via morphological changes and membrane damage of L. pneumophila. Our results suggest that TiO2 photocatalyst might be effective in controlling the spread of L. pneumophila.

Over the last two decades, oxide nanostructures have been continuously evaluated and used in many technological applications. The advancement of the controlled synthesis approach to design desired morphology is a fundamental key to the discipline of material science and nanotechnology. These nanostructures can be prepared via different physical and chemical methods; however, a green and ecofriendly synthesis approach is a promising way to produce these nanostructures with desired properties with less risk of hazardous chemicals. In this regard, ZnO and TiO2 nanostructures are prominent candidates for various applications. Moreover, they are more efficient, non-toxic, and cost-effective. This review mainly focuses on the recent state-of-the-art advancements in the green synthesis approach for ZnO and TiO2 nanostructures and their applications. The first section summarizes the green synthesis approach to synthesize ZnO and TiO2 nanostructures via different routes such as solvothermal, hydrothermal, co-precipitation, and sol-gel using biological systems that are based on the principles of green chemistry. The second section demonstrates the application of ZnO and TiO2 nanostructures. The review also discusses the problems and future perspectives of green synthesis methods and the related issues posed and overlooked by the scientific community on the green approach to nanostructure oxides.

The selective photocatalytic oxidation with O2 as oxidant of valencene and thymol was evaluated using nanostructured TiO2 under UV-Vis radiation at atmospheric conditions. The effect of the morphology and optical properties of TiO2 nanotubes and aminate nanoparticles was studied. Different scavengers were used to detect the presence of positive holes (h+), electrons (e−), hydroxyl radicals (•OH), and the superoxide radical anion (O2−) during the photooxidation reaction. Superoxide anion radical is the main oxidizing specie formed, which is responsible for the selective formation of nootkatone and thymoquinone using aminated TiO2 nanoparticles under 400 nm radiation.

SARS-CoV-2 is the causative agent of COVID-19, which is a global pandemic. SARS-CoV-2 is transmitted rapidly via contaminated surfaces and aerosols, emphasizing the importance of environmental disinfection to block the spread of virus. Ultraviolet C radiation and chemical compounds are effective for SARS-CoV-2 disinfection, but can only be applied in the absence of humans due to their toxicities. Therefore, development of disinfectants that can be applied in working spaces without evacuating people is needed. Here we showed that TiO2-mediated photocatalytic reaction inactivates SARS-CoV-2 in a time-dependent manner and decreases its infectivity by 99.9% after 20 min and 120 min of treatment in aerosol and liquid, respectively. The mechanistic effects of TiO2 photocatalyst on SARS-CoV-2 virion included decreased total observed virion count, increased virion size, and reduced particle surface spike structure, as determined by transmission electron microscopy. Damage to viral proteins and genome was further confirmed by western blotting and RT-qPCR, respectively. The multi-antiviral effects of TiO2-mediated photocatalytic reaction implies universal disinfection potential for different infectious agents. Notably, TiO2 has no adverse effects on human health, and therefore, TiO2-induced photocatalytic reaction is suitable for disinfection of SARS-CoV-2 and other emerging infectious disease-causing agents in human habitation.

Photocatalysis is a hopeful technology to solve various environmental problems, but it is still a technical task to produce large-scale photocatalysts in a simple and sustainable way. Here, nano-flower β-Bi2O3/TiO2 composites were prepared via a facile solvothermal method, and the photocatalytic performances of β-Bi2O3/TiO2 composites with different Bi/Ti molar ratios were studied. The nano-flower Bi2O3/TiO2 composites were studied by SEM, XRD, XPS, BET, and PL. The PL result proved that the construction of staggered heterojunction enhanced the separation efficiency of carriers. The degradation RhB was applied to study the photocatalytic performances of prepared materials. The results showed that the degradation efficiency of RhB increased from 61.2% to 99.6% when the molar ratio of Bi/Ti was 2.1%. It is a mesoporous approach to enhance photocatalytic properties by forming heterojunction in Bi2O3/TiO2 composites, which increases the separation efficiency of the generated carriers and improves photocatalytic properties. The photoactivity of the Bi2O3/TiO2 has no evident changes after the fifth recovery, indicating that the Bi2O3/TiO2 composite has distinguished stability.

Rhodamine B (RhB) is extensively used for dyeing purposes, and cannot be completely removed using traditional water treatment technologies. Here, we report for the first time the photodegradation of RhB using nitrogen-doped titanium dioxide (N-TiO2) on reduced graphene oxide (rGO) composite (N-TiO2/rGO). The work primarily highlights the synergistic effect of the incorporation of N-TiO2 and rGO and its kinetic study for the photodegradation of RhB. The N-TiO2/rGO composite was synthesized by dispersing titanium(IV) isopropoxide and urea, followed by annealing treatment via the hydrothermal method with rGO. Scanning electron microscopy (SEM) images illustrated that N-TiO2 particles with an irregular round shape and white color were dispersed onto the rGO surface. X-Ray diffraction (XRD) patterns revealed that N-TiO2/rGO composite showed an anatase phase of TiO2 with a diffraction peak of 2θ = 25.622°. The gas sorption analysis (GSA) showed that N-TiO2/rGO had surface area, pore volume, and pore size of 53.393 m2/g, 0.096 cc/g, and 3.588 nm, respectively. The thermogravimetric-differential thermal analysis (TG-DTA) showed an anatase phase of TiO2 that appeared at a temperature of 200–500 °C, with a weight loss of 2.50%. According to the ultraviolet-visible diffuse reflectance spectroscopy (UV-Vis DRS) study, TiO2, N-TiO2, and N-TiO2/rGO had band gap energies of 3.25, 2.95, and 2.86 eV, respectively. The highest photodegradation of RhB was obtained at the optimum condition in pH 2 with a photocatalyst mass of 20 mg and an irradiation time of 90 min. The photocatalytic activity of N-TiO2/rGO using visible light showed a higher percentage of photodegradation at 78.29%, compared to 44.08% under UV light. The kinetic study of the photodegradation of RhB using N-TiO2/rGO followed the pseudo-second-order model.

Particle size of nanomaterials has significant impact on their photocatalyst properties. In this paper, TiO2 nanoparticles with different crystalline sizes were prepared by adjusting the alkali-hydrothermal time (0–48 h). An annealing in N2 atmosphere after hydrothermal treatment caused TiO2 reduction and created defects, resulting in the visible light photocatalytic activity. The evolution of physicochemical properties along with the increase of hydrothermal time at a low alkali concentration has been revealed. Compared with other TiO2 samples, TiO2-24 showed higher photocatalytic activity toward degrading Rhodamine B and Sulfadiazine under visible light. The radical trapping and ESR experiments revealed that O2•- is the main reactive specie in TiO2-24. Large specific surface areas and rapid transfer of photogenerated electrons are responsible for enhancing photocatalytic activity. The above findings clearly demonstrate that particle size and surface oxygen defects can be regulated by alkali-hydrothermal method. This research will deepen the understanding of particle size on the nanomaterials performance and provide new ideas for designing efficient photocatalysts.