Explore the vast range of titles available.

The direct energy deposition (DED) metal additive manufacturing process enables rapid deposition and repair, providing an efficient approach to producing durable tool steel components. Here, 5 wt% Cr cold-work tool steel (Caldie) was developed by reducing carbon and chromium to suppress coarse carbide formation and by increasing molybdenum and vanadium to enhance dimensional stability. In this study, Caldie tool steel was fabricated via DED for the first time, and the effects of post-heat treatment on its hierarchical microstructure and mechanical properties were investigated and compared with those of wrought (reference) material. The as-built sample exhibited a mixed microstructure comprising lath martensite, retained austenite, polygonal ferrite, and carbide networks, which transformed into full martensite with fine carbides after heat treatment (DED-HT). The tensile strength of the DED Caldie material increased from 1340 MPa to 1949 MPa after heat treatment, demonstrating superior strength compared to other heat-treated, DED-processed high-carbon tool steels. Compared to DED-HT, the wrought material exhibited finer martensite, a more uniform Bain group distribution, and finer carbides, resulting in higher strength. This study provides insights into the effects of heat treatment on the hierarchical microstructure and mechanical behavior of Caldie tool steel manufactured by DED.

Additive manufacturing (AM) techniques such as selective laser melting (SLM) can enable the construction of injection moulding (IM) tools with conformal cooling channels that significantly improve performance through higher cooling uniformity and reduced cycle times. Design of IM cooling systems is typically achieved using commercial IM numerical modelling software originally developed for conventionally cooled mould designs. However, the accuracy of IM modelling software in predicting the performance of SLM manufactured tools with conformal cooling, across a range of moulding materials and processing conditions, has not been thoroughly evaluated in the literature. Furthermore, the SLM manufacturability and mechanical properties of tool steels typically applied in IM, such as AISI H13, are not well documented. This work addresses these deficiencies through the following: quantification of SLM H13 material properties, in particular fatigue strength which has not been previously reported; design and manufacture of a mould tool with easily exchangeable conventionally and conformally cooled inserts; and subsequent experimental validation of IM simulation software predictions under a range conditions. Result of mechanical testing showed SLM H13 parts to offer lower mechanical properties in the as-built condition compared to conventional materials; however, these increased substantially following residual stress reduction with heat treatment. Evaluation of the temperature prediction accuracy of IM numerical models showed generally high accuracy for conformally cooled SLM tools, although marginally lower when compared to conventionally cooled moulds. The outcomes of this work offer designers typical material property data for SLM manufactured H13 tooling, as well as an indication of the expected prediction accuracy of current commercial IM simulation software when applied to conformally cooled SLM tooling.

Conventional heat treatment is not capable of converting a sufficient amount of retained austenite into martensite in high-carbon or high-carbon and high-alloyed iron alloys. Cryogenic treatment induces the following alterations in the microstructures: (i) a considerable reduction in the retained austenite amount, (ii) formation of refined martensite coupled with an increased number of lattice defects, such as dislocations and twins, (iii) changes in the precipitation kinetics of nano-sized transient carbides during tempering, and (iv) an increase in the number of small globular carbides. These microstructural alterations are reflected in mechanical property improvements and better dimensional stability. A common consequence of cryogenic treatment is a significant increase in the wear resistance of steels. The current review deals with all of the mentioned microstructural changes as well as the variations in strength, toughness, wear performance, and corrosion resistance for a variety of iron alloys, such as carburising steels, hot work tool steels, bearing and eutectoid steels, and high-carbon and high-alloyed ledeburitic cold work tool steels.

The ability of cryogenic treatment to improve tool steel performance is well established; however, the selection of optimal heat treatment is pivotal for cost reduction and extended tool life. This investigation delves into the influence of distinct cryogenic and tempering treatments on the hardness, fracture toughness, and tribological properties of Vanadis 6 tool steel. Emphasis was given to comprehending wear mechanisms, wear mode identification, volume loss estimation, and detailed characterization of worn surfaces through scanning electron microscopy coupled with energy dispersive spectroscopy and confocal microscopy. The findings reveal an 8–9% increase and a 3% decrease in hardness with cryogenic treatment compared to conventional treatment when tempered at 170 °C and 530 °C, respectively. Cryotreated specimens exhibit an average of 15% improved fracture toughness after tempering at 530 °C compared to conventional treatment. Notably, cryogenic treatment at −140 °C emerges as the optimum temperature for enhanced wear performance in both low- and high-temperature tempering scenarios. The identified wear mechanisms range from tribo-oxidative at lower contacting conditions to severe delaminative wear at intense contacting conditions. These results align with microstructural features, emphasizing the optimal combination of reduced retained austenite and the highest carbide population density observed in −140 °C cryogenically treated steel.

The powder-pack boriding technique with an open retort was used to form borided layers on X165CrV12 tool steel. The process was carried out at 1123, 1173, and 1223 K for 3, 6, and 9 h. As a result of boriding the high-chromium substrate, the produced layers consisted of three zones: an outer FeB layer, an inner Fe2B layer, and a transition zone, below which the substrate material was present. Depending on the applied parameters of boriding, the total thickness of the borided layers ranged from 12.45 to 78.76 µm. The increased temperature, as well as longer duration, was accompanied by an increase in the thickness of the FeB zone and the total layer thickness. The integral diffusion model was utilized to kinetically describe the time evolution of the thickness of the FeB and (FeB + Fe2B) layers grown on the surface of powder-pack borided X165CrV12 steel. The activation energy of boron for the FeB phase was lower than that for the Fe2B phase. This suggested that the FeB phase could be formed before the Fe2B phase appeared in the microstructure. The high chromium concentration in X165CrV12 steel led to the formation of chromium borides in the borided layer, which increased the hardness (21.88 ± 1.35 GPa for FeB zone, 17.45 ± 1.20 GPa for Fe2B zone) and Young’s modulus (386.27 ± 27.04 GPa for FeB zone, 339.75 ± 17.44 GPa for Fe2B zone). The presence of the transition zone resulted from the accumulation of chromium and carbon atoms at the interface between the tips of Fe2B needles and the substrate material. The presence of hard iron and chromium borides provided significant improvement in the wear resistance of X165CrV12 steel. The powder-pack borided steel was characterized by a four times lower mass wear intensity factor and nine times lower ratio of mass loss to the length or wear path compared to the non-borided material.

In connection with the growing importance of the efficiency and reliability of tools in industrial sectors, our research represents a key step in the effort to optimize production processes and increase their service life in real conditions. The study deals with the comparison of the tribological properties of three tool steels, two of which were produced by the powder metallurgy method—ASP2017 and ASP2055—and the last tool steel underwent the conventional production method—X153CrMoV12. The samples were mechanically machined with the finishing technology of turning and, finally, heat treated (Q + T). The study focused on the evaluation of hardness, resulting microstructure, wear resistance, and coefficient of friction (COF). The ball-on-disc method was chosen as part of the COF and wear resistance test. The tribological test took place at room temperature with dry friction to accelerate surface wear. The pressing material was a hardened steel ball G40 (DIN 100Cr6). Measurements were performed at loads of 10 N, 6 N, and 2 N and turning radii of 13 mm, 18 mm, and 23 mm, which represents a peripheral speed of 0.34, 0.47, and 0.60 m/s. The duration of the measurement for each sample was 20 min. The results showed that the COF of powder steels showed almost the same values, while a significant difference occurred with the increase of the radius rotation in the case of conventional steel. The results within the friction mechanism showed two types of wear, namely, adhesive and abrasive wear, depending on the Q + T process. From a tribological point of view in terms of wear, it was possible to state that the material ASP2055 after Q + T showed the lowest rate of wear of all the tested steels.

With the rising need to promote productivity that is based on quality, energy, and cost, it is imperative that cutting tools are not just selected on the basis of its suitability, but on its efficiency. It is particularly important that workpiece materials are aligned to specific cutting tools, to improve manufacturing costs, lead time, and quality of the overall product and to create flexibility. For this reason, a comparative study of the performance of high-speed steel and tungsten carbide cutting tools has been performed to determine the most suitable for the machining of a 304 Austenite Steel cylindrical bar. The tool wear of the cutting tools was selected as a measured to ascertain their performance in the turning operation. Response surface methodology was employed to analyzing the results and determining their optimal performance. From the study, the tungsten carbide tool recorded optimal parameters as follows: cutting speed 1303 m/min, feed rate 0.354 mm/rev, and depth of cut 0.458 mm with a tool wear of 1.173 mm and for the high-speed steel tool, cutting speed 1321 m/min, feed rate 0.208 mm/rev, and depth of cut 0.682 mm with a tool wear of 2.073 mm. The study judging from the tool wear shows the efficiency of the tungsten carbide tool over the high-speed steel cutting tool, as it can be seen from the results obtained that the lowest tool wear in the turning of the cylindrical steel bar is recorded from the use of the tungsten carbide cutting tool. From the 3D surface plots, it can be confirmed that to obtain a good performance from the different cutting tools, the cutting speed best suited for the cutting tool must be taken into consideration.

The impact of manufacturing strategies on the development of residual stresses in Dievar steel is presented. Two fabrication methods were investigated: conventional ingot casting and selective laser melting as an additive manufacturing process. Subsequently, plastic deformation in the form of hot rotary swaging at 900 °C was applied. Residual stresses were measured using neutron diffraction. Microstructural and phase analysis, precipitate characterization, and hardness measurement—carried out to complement the investigation—showed the microstructure improvement by rotary swaging. The study reveals that the manufacturing method has a significant effect on the distribution of residual stresses in the bars. The results showed that conventional ingot casting resulted in low levels of residual stresses (up to ±200 MPa), with an increase in hardness after rotary swaging from 172 HV1 to 613 HV1. SLM-manufactured bars developed tensile hoop and axial residual stresses in the vicinity of the surface and large compressive axial stresses (−600 MPa) in the core due to rapid cooling. The subsequent thermomechanical treatment via rotary swaging effectively reduced both the surface tensile (to approximately +200 MPa) and the core compressive residual stresses (to −300 MPa). Moreover, it resulted in a predominantly hydrostatic stress character and a reduction in von Mises stresses, offering relatively favorable residual stress characteristics and, therefore, a reduction in the risk of material failure. In addition to the significantly improved stress profile, rotary swaging contributed to a fine grain (3–5 µm instead of 10–15 µm for the conventional sample) and increased the hardness of the SLM samples from 560 HV1 to 606 HV1. These insights confirm the utility of rotary swaging as a post-processing technique that not only reduces residual stresses but also improves the microstructural and mechanical properties of additively manufactured components.

In this research, samples of the H13 steel, a commonly used hot work tool steel in the die/mould manufacturing industry, were additively manufactured using selective laser melting (SLM). Their as-built microstructures were characterised in detail using transmission electron microscopy (TEM) and compared with that of the conventionally manufactured H13 (as-supplied). SLM resulted in the formation of martensite and also its partial decomposition into fine α-Fe and Fe 3 C precipitates along with retained austenite. TEM analyses further revealed that the lattice of the resulting α-Fe phase is slightly distorted due to enhanced Cr, Mo and V contents. Substantially high residual stresses in the range of 940–1420 MPa were detected in the as-built H13 samples compared with its yield strength of ~1650 MPa. In addition, it was identified that the high residual stress existed from just about two additive layers (100 µm) above the substrate along the build direction. The high residual stresses were mainly attributed to the martensitic transformation that occurred during SLM. The research findings of this study suggest that the substantially high residual stresses can be easily problematic in the AM of intricate H13 dies or moulds by SLM.

This study refers to an analysis of the dies used in the first operation of producing a valve forging from chromium-nickel steel NC3015. The analyzed process of manufacturing forgings of exhaust valves is realized in the co-extrusion technology, followed by forging in closed dies. This type of technology is difficult to master, mainly due to the increased adhesion of the charge material to the tool substrate as well as the complex conditions of the tools’ operations, which are caused by the cyclic thermo-mechanical loads and also the hard tribological conditions. The average durability of tools made from tool steel WLV (1.2365), subjected to thermal treatment and nitriding, equals about 1000 forgings. In order to perform an in-depth analysis, a complex analysis of the presently realized technology was conducted in combination with multi-variant numerical simulations. The obtained results showed numerous cracks on the tools, especially in the cross-section reduction area, as well as sticking of the forging material, which, with insufficient control of the tribological conditions, can cause premature wear of the dies. In order to increase the durability of forging dies, alternative materials made of hot work tool steels were used: QRO90 Supreme, W360, and Unimax. The preliminary tests showed that the best results were obtained for QRO90, as the average durability for the tools made of this steel equaled about 1200 forgings (with an increase in both the minimal and maximal values), with reference to the 1000 forgings for the material applied so far.