Explore the vast range of titles available.

The Internet of Things (IoT) technology has grown rapidly over the past decade, resulting in deployments of thousands of IoT devices around the world. Then, managing firmware updates for these numerous devices poses significant challenges. Firmware updates face issues such as version rollback, modified firmware files, and potential man-in-the-middle (MITM) attacks, highlighting the need for a secure over-the-air (OTA) firmware update mechanism. In this paper, we propose an automated OTA firmware update mechanism, integrated with continuous integration (CI) and continuous delivery (CD) to ensure trusted sources for firmware origins. It offers security, error handling during firmware updates, and monitoring of the update process. For evaluations, we implemented the proposal with the SEMAR IoT application server that has been implemented in our previous studies. Then, we verified the integrity and authentication, measured the performance and resource utilization, and performed benchmarking tests to assess the efficiency. The results demonstrate that the proposal is sufficiently reliable and efficient.

The capacity to update firmware is a vital component in the lifecycle of Internet of Things (IoT) devices, even those with restricted hardware resources. This paper explores the best way to wirelessly (Over The Air, OTA) update low-end IoT nodes with difficult access, combining the use of unicast and broadcast communications. The devices under consideration correspond to a recent industrial IoT project that focuses on the installation of intelligent lighting systems within ATEX (potentially explosive atmospheres) zones, connected via LoRa to a gateway. As energy consumption is not limited in this use case, the main figure of merit is the total time required for updating a project. Therefore, the objective is to deliver all the fragments of the firmware to each and all the nodes in a safe way, in the least amount of time. Three different methods, combining unicast and broadcast transmissions in different ways, are explored analytically, with the aim of obtaining the expected update time. The methods are also tested via extensive simulations, modifying different parameters such as the size of the scenario, the number of bytes of each firmware chunk, the number of nodes, and the number of initial broadcast rounds. The simulations show that the update time of a project can be significant, considering the limitations posed by regulations, in terms of the percentage of airtime consumption. However, significant time reductions can be achieved by using the proper method: in some cases, when the number of nodes is high, the update time can be reduced by two orders of magnitude if the correct method is chosen. Moreover, one of the proposed methods is implemented using actual hardware. This real implementation is used to perform firmware update experiments in a lab environment. Overall, the article illustrates the advantage of broadcast approaches in this kind of technology, in which the transmission rate is constant despite the distance between the gateway and the node. However, the advantage of these broadcast methods with respect to the unicast one could be mitigated if the nodes do not run exactly the same firmware version, since the control of the broadcast update would be more difficult and the total update time would increase.

The Internet of Things (IoT) is being deployed to provide smart solutions for buildings, logistics, hospitals, and many more. It is growing with billions of connected devices. However, with such tremendous growth, maintenance and support are the hidden burdens. The devices deployed for IoT generally have a light microcontroller, low-power, low memory, and lightweight software. The software, which includes firmware and applications, can be managed remotely via a wireless connection. This improves flexibility, installation time, accessibility, effectiveness, and cost. The firmware can be updated constantly to remove known bugs and improve the functionality of the device. This work presents an approach to update firmware over-the-air (OTA) for constrained IoT devices. We used Narrowband IoT (NB-IoT) as the wireless communication standard to communicate between the managing server and devices. NB-IoT is one of the most promising low power wide area (LPWA) network protocols that supports more than 50k devices within a cell using a licensed spectrum. This work is a proof of concept demonstrating the usage of NB-IoT to update firmware for constrained devices. We also calculated the overall power consumption and latency for different sizes of the firmware.

Message Queuing Telemetry Transport (MQTT) is one of the dominating protocols for edge- and cloud-based Internet of Things (IoT) solutions. When a security vulnerability of an IoT device is known, it has to be fixed as soon as possible. This requires a firmware update procedure. In this paper, we propose a secure update protocol for MQTT-connected devices which ensures the freshness of the firmware, authenticates the new firmware and considers constrained devices. We show that the update protocol is easy to integrate in an MQTT-based IoT network using a semantic approach. The feasibility of our approach is demonstrated by a detailed performance analysis of our prototype implementation on a IoT device with 32 kB RAM. Thereby, we identify design issues in MQTT 5 which can help to improve the support of constrained devices.

Internet of Things (IoT) devices rely upon remote firmware updates to fix bugs, update embedded algorithms, and make security enhancements. Remote firmware updates are a significant burden to wireless IoT devices that operate using low-power wide-area network (LPWAN) technologies due to slow data rates. One LPWAN technology, Long Range (LoRa), has the ability to increase the data rate at the expense of range and noise immunity. The optimization of communications for maximum speed is known as adaptive data rate (ADR) techniques, which can be applied to accelerate the firmware update process for any LoRa-enabled IoT device. In this paper, we investigate ADR techniques in an application that provides remote monitoring of cattle using small, battery-powered devices that transmit data on cattle location and health using LoRa. In addition to issues related to firmware update speed, there are significant concerns regarding reliability and security when updating firmware on mobile, energy-constrained devices. A malicious actor could attempt to steal the firmware to gain access to embedded algorithms or enable faulty behavior by injecting their own code into the device. A firmware update could be subverted due to cattle moving out of the LPWAN range or the device battery not being sufficiently charged to complete the update process. To address these concerns, we propose a secure and reliable firmware update process using ADR techniques that is applicable to any mobile or energy-constrained LoRa device. The proposed system is simulated and then implemented to evaluate its performance and security properties.

The remarkable evolution of the IoT raised the need for an efficient way to update the device’s firmware. Recently, a new process was released summarizing the steps for firmware updates over the air (FUOTA) on top of the LoRaWAN protocol. The FUOTA process needs to be completed quickly to reduce the systems’ interruption and, at the same time, to update the maximum number of devices with the lowest power consumption. However, as the literature showed, a single gateway cannot optimize the FUOTA procedure and offer the above mentioned goals since various trade-offs arise. In this paper, we conducted extensive experiments via simulation to investigate the impact of multiple gateways during the firmware update process. To achieve that, we extended the FUOTAsim simulation tool to support multiple gateways. The results revealed that several gateways could eliminate the trade-offs that appeared using a single gateway.

This paper presents an efficient and secure method for updating firmware in IoT devices using LoRaWAN network resources and communication protocols. The proposed method involves dividing the firmware into fragments, storing them in the application server’s database, and transmitting them to remote IoT devices via downlink messages, without necessitating any changes to the device’s class. This approach can be replicated across any IoT LoRaWAN device, offering a robust and scalable solution for large-scale firmware updates while ensuring data security and integrity. The proposed method significantly reduces the downtime of IoT devices and enhances the energy efficiency of the update process. The method was validated by updating a block in the program memory, associated to a specific functionality of the IoT end device. The associated Intel Hex file was segmented into 17 LoRaWAN downlink frames with an average size of 46 bytes. Upon receiving the complete firmware update, the microcontroller employs self-programming techniques that restrict the update process to specific rows of the program memory, avoiding interruptions or reboots. The update process was successfully completed in 51.33 ms, resulting in a downtime of 16.88 ms. This method demonstrates improved energy efficiency compared to existing solutions while preserving the communication network’s capacity, making it an adequate solution for remote devices in LoRaWAN networks.

IoT (Internet of Things) use cases cover all the verticals of industry/organization. From manufacturing unit to building management, from X protocol to Y protocol, from A device to Z device; everywhere it is using. The number of IoT devices is increasing exponentially, especially in remote areas. These devices, which are deployed, need to update also, as the software development process for an IoT device is not a one-time action. Even devices running on a small software needs to be updated with the time for bug fixing or feature addition.“Using more computing to move less data” is the new computing paradigm. Hence, low internet connectivity for large computing scale software updates of such IoT devices must be considered. In this paper, we proposed an implementation of a method that needed low internet connectivity for Firmware Over the Air (FOTA) of embedded devices.

The pervasiveness of IoT and embedded devices allows the deployment of services that were unthinkable only few years ago. Such devices are typically small, run unattended, possibly on batteries and need to have a low cost of production. As all software systems, this type of devices need to be updated for different reasons, e.g., introducing new features, improving/correcting existing functionalities or fixing security flaws. At the same time, because of their low-complexity, standard software distribution platforms and techniques cannot be used to update the software. In this paper we review the current limitations posed to software distribution systems for embedded/IoT devices, consider challenges that the researchers in this area have been identifying and propose the corresponding solutions.

The broadly configured smart city network requires a variety of security considerations for a heterogeneous device environment. Because a network of heterogeneous devices facilitates an attacker’s intrusion through a specific device or node, a device management framework is required to manage each node comprehensively. This paper proposes a blockchain-based device management framework for efficient device management, scalable firmware update and resiliences on attacks against smart city network. This framework offers four device management and firmware update mechanisms based on the performance and requirements of each device: bidirectional mechanism of general end node and a unidirectional mechanism of the lightweight end node. This difference optimizes the resource of network and devices in terms of management and security. All management history of each device is stored in the blockchain and transmitting firmware between vendor and management node is conducted through a smart contract of blockchain for security and resilience on the attack. Through the framework proposed in this paper, the confidentiality and availability of device management on smart city network as well as integrity, auditability, adaptability and authentication for each node are ensured and the effectiveness of the proposed framework is presented through the security analysis.