Explore the vast range of titles available.

Further to systematic experiments on the flexural strength of laboratory-grown, fresh water ice loaded cyclically, this paper describes results from new experiments of the same kind on lake ice harvested in Svalbard. The experiments were conducted at −12 °C, 0.1 Hz frequency and outer-fiber stress in the range from ~ 0.1 to ~ 0.7 MPa. The results suggest that the flexural strength increases linearly with stress amplitude, similar to the behavior of laboratory-grown ice.

New experiments have revealed that a thin layer of granular ice bonded to salty and to salt-free columnar-grained ice increases flexural strength when the composite material is rapidly bent to the point of failure through brittle fracture. When bent slowly within the regime of ductile behavior, the layer has no detectable effect. Strengthening is attributed to the suppression of cracking; its absence, to dislocation creep.

An intermediate-depth (1751 m) ice core was drilled at the South Pole between 2014 and 2016 using the newly designed US Intermediate Depth Drill. The South Pole ice core is the highest-resolution interior East Antarctic ice core record that extends into the glacial period. The methods used at the South Pole to handle and log the drilled ice, the procedures used to safely retrograde the ice back to the National Science Foundation Ice Core Facility (NSF-ICF), and the methods used to process and sample the ice at the NSF-ICF are described. The South Pole ice core exhibited minimal brittle ice, which was likely due to site characteristics and, to a lesser extent, to drill technology and core handling procedures.

Over the course of the 2014/15 and 2015/16 austral summer seasons, the South Pole Ice Core project recovered a 1751 m deep ice core at the South Pole. This core provided a high-resolution record of paleoclimate conditions in East Antarctica during the Holocene and late Pleistocene. The drilling and core processing were completed using the new US Intermediate Depth Drill system, which was designed and built by the US Ice Drilling Program at the University of Wisconsin–Madison. In this paper, we present and discuss the setup, operation, and performance of the drill system.

Systematic experiments reveal that the flexural strength of freshwater S2 columnar-grained ice loaded normal to the columns increases upon cyclic loading. Specifically, over the range of stress amplitudes 0.1–2.6 MPa the flexural strength increases linearly with increasing stress amplitude. The experiments were conducted upon both reversed and non-reversed cyclic loading over ranges of frequencies from 0.03 to 2 Hz and temperatures from −25 to −3°C. Strengthening can also be imparted through bending-induced creep. The fundamental requirement for strengthening is that the surface that undergoes maximum tensile stress during failure must have been pre-stressed in tension. Flexural strength is governed by crack nucleation. We suggest that the process is resisted by an internal back-stress that opposes the applied stress and builds up through either crystal dislocations piling up or grain boundaries sliding.

The Japanese second deep ice coring project was carried out at Dome Fuji, Antarctica. Following the drilling of the pilot hole in 2001, deep ice core drilling led by the Japanese Antarctic Research Expedition (JARE) was conducted over four austral summer seasons, beginning with the 2003/04 season and reached a depth of 3035.22 m near the bedrock in January 2007. The new drill was designed and developed with the goals of (1) solving the problems encountered during the first JARE deep coring drill and (2) achieving more efficient drilling. In particular, the maximum core length that can be drilled at one time was increased from 2.30 m to 3.84 m and the chip storage efficiency was enhanced by a special pipe with many small holes. This paper gives an outline of the improved drilling system, the progress of drilling and various drilling data.

We developed a novel laser melting sampler (LMS) for ice cores to measure the stable water isotope ratios (δ18O and δD) as temperature proxies at sub-centimeter depth resolutions. In this LMS system, a 2 mm diameter movable evacuation nozzle holds an optical fiber through which a laser beam irradiates the ice core. The movable nozzle intrudes into the ice core, the laser radiation meanwhile melts the ice cylindrically, and the meltwater is pumped away simultaneously through the same nozzle and transferred to a vial for analysis. To avoid isotopic fractionation of the ice through vaporization, the laser power is adjusted to ensure that the temperature of the meltwater is always kept well below its boiling point. A segment of a Dome Fuji shallow ice core (Antarctica), using the LMS, was then demonstrated to have been discretely sampled with a depth resolution as small as 3 mm: subsequent analysis of δ18O, δD, and deuterium excess (d) was consistent with results obtained by hand segmentation within measurement uncertainties. With system software to control sampling resolution, the LMS will enable us to identify temperature variations that may be detectable only at sub-centimeter resolutions in ice cores.

A new, modified version of the cable-suspended Ice and Bedrock Electromechanical Drill (IBED) was designed for drilling in firn, ice, debris-rich ice and rock. The upper part of the drill is almost the same for all drill variants and comprises four sections: cable termination, a slip-ring section, an antitorque system and an electronic pressure chamber. The lower part of the IBED comprises an auger core barrel, reamers, a core barrel for ice/debris-ice drilling and a conventional geological single-tube core barrel or custom-made double-tube core barrel. First, the short and full-scale field versions of the IBED were tested at an outdoor testing stand and a testing facility with a 12.5 m-deep ice well. Then, in the 2018–2019 summer season, the IBED was tested in the field at a site ~12 km south of Zhongshan Station, East Antarctica, and a ~6 cm bedrock core was recovered from a 198 m-deep borehole. A total of 18 d was required to penetrate the ice sheet. The retrieved core samples of blue ice, basal ice and bedrock provided valuable information regarding the Earth's paleo-environment.

A deep ice core was drilled at Dome A, Antarctic Plateau, East Antarctica, which started with the installation of a casing in January 2012 and reached 800.8 m in January 2017. To date, a total of 337 successful ice-core drilling runs have been conducted, including 118 runs to drill the pilot hole. The total drilling time was 52 days, of which eight days were required for drilling down and reaming the pilot hole, and 44 days for deep ice coring. The average penetration depths of individual runs were 1 and 3.1 m for the pilot hole drilling and deep ice coring, respectively. The quality of the ice cores was imperfect in the brittle zone (650−800 m). Some of the troubles encountered are discussed for reference, such as armoured cable knotting, screws falling into the hole bottom, and damaged parts, among others.

Atmospheric ice accretion results from the exposure of technical equipment or facilities to cold and humid environments. Supercooled droplets in a cloud can impact an airplane's surface and quickly form an ice layer. The presence of air pockets in such a layer is well known and explains the white appearance of some of the accretions. However, estimation of its porosity values and studies on the pore formation mechanics remain limited. In this study, we performed tests in an icing wind tunnel and scans with micro-computed tomography to address these issues. Here, we show that the accretion has closed porosity below 1%, which is mostly produced by the interaction between a spray-like impact on the water surface. The insights we provide here are important to improve ice accretion modelling techniques and establish a different approach to address the interaction between the cloud and the surfaces exposed to atmospheric icing.