Explore the vast range of titles available.

An on-line multi-frequency electrical resistance tomography (mfERT) device with a melt-resistive sensor and noise reduction hardware has been proposed for crystalline phase imaging in high-temperature molten oxide. The melt-resistive sensor consists of eight electrodes made of platinum-rhodium (Pt-20mass%Rh) alloy covered by non-conductive aluminum oxide (Al2O3) to prevent an electrical short. The noise reduction hardware has been designed by two approaches: (1) total harmonic distortion (THD) for the robust multiplexer, and (2) a current injection frequency pair: low fL and high fH, for thermal noise compensation. THD is determined by a percentage evaluation of k-th harmonic distortions of ZnO at f=0.1~10,000 Hz. The fL and fH are determined by the thermal noise behavior estimation at different temperatures. At  f <100 Hz, the THD percentage is relatively high and fluctuates; otherwise, THD dramatically declines, nearly reaching zero. At the determined fL≥ 10,000 Hz and fH≈ 1,000,000 Hz, thermal noise is significantly compensated. The on-line mfERT was tested in the experiments of a non-conductive Al2O3 rod dipped into conductive molten zinc-borate (60ZnO-40B2O3) at 1000~1200 °C. As a result, the on-line mfERT is able to reconstruct the Al2O3 rod inclusion images in the high-temperature fields with low error, ςfL, T = 5.99%, at 1000 °C, and an average error ⟨ςfL⟩ = 9.2%.

Accurate analysis of the air gap magnetic field is the focus of research in the field of precision permanent magnet linear synchronous motors. In this paper, the two-dimensional air gap magnetic field of a secondary trapezoidal Halbach permanent magnet array coreless permanent magnet linear synchronous motor (PMLSM) was taken as our research object. On the basis of the equivalent surface current method, we proposed an improved equivalent analytical algorithm with a trapezoidal side length unit. The equivalent analytical model of the magnetic induction vector of the two-dimensional air gap was established, and the air gap magnetic field of the trapezoidal Halbach array coreless PMLSM was calculated. At the same time, we analyzed the influence of the bottom angle α of a trapezoidal permanent magnet equivalent width coefficient αw, pole height coefficient αh, and air gap height coefficient αg on the amplitude (Bpeak) and total harmonic distortion (THDB) of the central magnetic field in the air gap. The results show that α and αw have a significant influence on the Bpeak and THDB of the central magnetic field air gap. With the synergy of α and αw, we identified the “flux convergence” effect, which makes the maximum range of Bpeak α > 90° and αw < 0.5. We also found the “equilateral” effect, which causes the minimum region of THDB to change linearly. The calculation results of the improved equivalent surface current analytical model established in this paper agree with those verified by the finite element method. The calculation is convenient, and the accuracy of the result is high. This research provides a new method for analyzing the air gap magnetic field of a permanent magnet with a nonrectangular cross-section and lays a theoretical foundation for optimizing the PMLSM pole model.

The use of advanced modulation and control schemes for power converters, such as a Feedback Quantizer and Predictive Control, is widely studied in the literature. This work focuses on improving the closed-loop modulation scheme called Feedback Quantizer, which is applied to a three-phase voltage source inverter. This scheme has the natural behavior of mitigating harmonics at low frequencies, which are detrimental to electrical equipment such as transformers. This modulation scheme also provides good tracking for the voltage reference at the fundamental frequency. On the other hand, the disadvantage of this scheme is that it has a variable switching frequency, creating a harmonic spectrum in frequency dispersion, and it also needs a small sampling time to obtain good results. The proposed scheme to improve the modulation scheme is based on a Discrete Space Vector with virtual vectors to obtain a better approximation of the optimal vectors for use in the algorithm. The proposal improves the conventional scheme at a high sampling time (200 μs), obtaining a THD less than 2% in the load current, decreases the noise created by the conventional scheme, and provides a fixed switching frequency. Experimental tests demonstrate the correct operation of the proposed scheme.

Demand Response (DR) plays a vital role in a smart grid, helping consumers plan their usage patterns and optimize electricity consumption and also reduce harmonic pollution in a distribution grid without compromising on their needs. The first step of DR is the disaggregation of loads and identifying them individually. The literature suggests that this is accomplished through electric features. Present-day households are using modern power electronic-based nonlinear loads such as LED (Light Emitting Diode) lamps, electronic regulators and digital controllers to reduce the electricity consumption. Furthermore, usage of SMPS (Switched-Mode Power Supply) for computing and mobile phone chargers is increasing in every home. These nonlinear loads, while reducing electricity consumption, also introduce harmonic pollution into the distribution grid. This article presents a deterministic approach to the non-intrusive identification of load patterns using percentage Total Harmonic Distortion (THD) for DR management from a Power Quality perspective. The percentage THD of various combinations of loads is estimated by enhanced dual-spectrum line interpolated FFT (Fast Fourier Transform) with a four-term minimal side-lobe window using a LabVIEW-based hardware setup in real time. The results demonstrate that percentage THD identifies a different combination of loads effectively and advocates alternate load combinations for recommending to the consumer to reduce harmonic pollution in the distribution grid.

Silicon carbide (SiC)-based switching devices provide significant performance improvements in many aspects, including lower power dissipation, higher operating temperatures, and faster switching; compared with conventional Si devices, all these features contribute to these devices generating interest in applications for electric traction systems. The topology that is frequently used in these systems is the voltage source inverter (VSI), but the use of SiC devices in the current source inverter topology (CSI), which is considered as an emerging topology, generates interest. This paper presents a method for improving total harmonic distortion (THD) in the currents of output and efficiency in SiC current source inverter for future application in an electric traction system. The method that is proposed consists of improving the coupling of a bidirectional converter topology, voltage current (V-I) and CSI. The V-I converter serves as a current regulator for the CSI, and allows for the recovery of energy. The method involves an effective selection of the switching frequencies and phase angles for the carrier signals that are present in each converter topology. With this method, it is expected to have a reduction of the total harmonic distortion, THD in the output currents. In addition, a comparative analysis between converters with all-SiC technology and converters with hybrid technology is realized, to verify the impact of the SiC devices in the power converters efficiency.

Since multicarrier based modulation techniques are simple to implement and can be used to control inverters at any level, they are frequently employed in modern multilevel inverters in high or medium power applications. When considering the many multi-carrier modulation techniques available, level-shifted pulse-width modulation (LSPWM) is often chosen for its superior harmonic performance. However, this traditional LSPWM method is not suitable for controlling newly proposed reduced switch count (RSC) MLI topologies. The research work in this paper seeks to elucidate the reasons why conventional LSPWM is ineffective in controlling RSC MLI topologies, and proposes a generalized LSPWM system based on logical expressions. The proposed method can be utilized with symmetrical and asymmetrical RSC MLIs, and can be extended to an arbitrary number of levels. The merit of the proposed method for controlling any RSC configuration with satisfactory line-voltage THD (≈1.8%) performance (identical to conventional LSPWM) was evaluated using multiple 13-level asymmetrical RSC-MLI topologies. A MATLAB model was developed and then subjected to simulation and real-world testing to prove the effectiveness of the proposed modulation strategy.

The hybrid AC-DC microgrid (MG) has gained popularity recently as it offers the benefits of AC and DC systems. Interconnecting AC-DC converters are necessary since the MG has both DC and AC sub-grids. Adding an extra harmonic adjustment mechanism to the interlinking converters is promising because non-linear AC loads can worsen the quality of the voltage on the AC bus. The interlinking converters’ primary function is to interchange real and reactive power between DC and AC sub-grids, so the typical harmonic controlling approach implemented for active power filters (APFs) might not be appropriate for them. When the MG’s capacity is high, it is desirable that the switching frequency be lesser than the APFs. The performance of harmonic correction or even system stability may suffer at low switching frequencies. In this study, a harmonic compensating technique appropriate for hybrid AC-DC interlinking converters with lower switching frequencies is planned. The suggested strategy, modeling techniques, stability analysis, and a thorough virtual impedance design are discussed in this work.

Summary In this paper, the authors present a new method for simultaneous optimal placement and sizing (PLAS) of the passive power filters (PPFs) and active power filters (APFs) with acceptable standard levels. Total harmonic distortion of voltage, total harmonic distortion of current, harmonic transmission line loss and total cost of installed PPFs and APFs are the four objectives considered in the optimization, while individual and total harmonic distortion, fundamental reactive power compensation, parallel and series resonance, detuning of the PPFs and maximum allowable APF size are satisfied with predetermined trust levels. The proposed model is one of the non‐convex optimization problems having a non‐linear mixed‐integer nature. Hence, a new improved harmony search algorithm (IHSA) is used and followed by a fuzzy satisfying method in order to obtain the final optimal solution. The IHSA is a recently developed optimization algorithm which imitates the music improvisation process. In this process, the Harmonists improvise their instrument pitches searching for the perfect state of harmony. The newly developed method has been implemented on the IEEE 18‐bus test system by three cases to demonstrate the feasibility and effectiveness of the proposed method. Simulation results illustrate the sufficiency and profitableness of the newly developed method in the PLAS of the multiple passive and APFs, when compared with other methods. Copyright © 2013 John Wiley & Sons, Ltd.

In recent modern power systems, the number of renewable energy systems (RESs) and nonlinear loads have become more prevalent. When these systems are connected to the electricity grid, they may face new difficulties and issues such as harmonics and non-standard voltage. The proposed study suggests the application of a whale optimization algorithm (WOA) based on a fractional-order proportional-integral controller (FOPIC) for unified power quality conditioner (UPQC) and STATCOM tools. These operate best with the help of their improved control system, to increase the system’s reliability and fast dynamic response, and to decrease the total harmonic distortion (THD) for enhancing the power quality (PQ). In this article, three different configurations are studied and assessed, namely: (C1) WOA-based FOPIC for UPQC, (C2) WOA-based FOPIC for STATCOM, and (C3) system without FACTS, i.e., base case, to mitigate the mentioned drawbacks. C3 is also considered as a base case to highlight the main benefits of C1 and C2 in improving the PQ by reducing the %THD of the voltage and current system and improving the systems’ voltage waveforms. With C2, voltage fluctuation is decreased by 98%, but it nearly disappears in C1 during normal conditions. Additionally, during the fault period, voltage distortion is reduced by 95% and 100% with C2 and C1, respectively. Furthermore, when comparing C1 to C2 and C3 under regular conditions, the percentage reduction in THD is remarkable. In addition, C1 eliminates the need for voltage sag, and harmonic and current harmonic detectors, and it helps to streamline the control approach and boost control precision. The modeling and simulation of the prepared system are performed by MATLAB/Simulink. Finally, it can be concluded that the acquired results are very interesting and helpful in the recovery to the steady state of wind systems and nonlinear loads, thereby increasing their grid connection capabilities.