Explore the vast range of titles available.

Thoroughly revised, this book provides the reader with an understanding of the principles and practices of testing and balancing (TAB) heating, ventilating, and air conditioning (HVAC) air and water systems. For the novice and the experienced testing and balancing technician, it is a field reference book of procedures, equations, and information tables. Divided into five parts, Part I has general and specific balancing procedures for constant air volume systems, variable air volume systems, return air systems, and fans and fan performance. Part II covers testing and balancing fume hood systems and cleanrooms, commissioning HVAC systems, centrifugal pumps and pump performance, analog and digital controls and water balancing procedures using flow meters, system components, and temperatures. Part III covers fans, pumps, air distribution, water distribution, motors, electrical, fluid flow, psychrometrics, refrigeration, and instrument usage and care. Part IV includes equations and tables. New to this edition, Part V has information and additional test and balance procedures and graphics for chapters 1-7 and 13-14. TAB Data and Test forms are in the new addendum as well. • Provides the readers with revised information about the principles and practices of testing and balancing (TAB) heating • Represents a field reference guide for both the novice and experienced testing and balancing technician • Includes a new section with information and additional test and balance procedures and graphics

\"This book introduces a variety of non-destructive testing (NDT) methods, including testing and application cases. New ultrasonic testing technology for complex workpieces is proposed\"-- Provided by publisher.

Passive-wireless surface-acoustic-wave (SAW) micro-pressure sensors are suitable for extreme scenarios where wired sensors are not applicable. However, as the measured pressure decreases, conventional SAW micro-pressure sensors struggle to meet expected performance due to insufficient sensitivity. This article proposes a a method of using an A[sub.2]-mode Lamb SAW sensor and introduces an inertial structure in the form of a cantilever beam to enhance sensitivity. An MEMS-compatible manufacturing process was employed to create a multi-layer structure of SiO[sub.2], AlN, and SOI for the SAW micro-pressure sensor. To investigate the operational performance of the SAW micro-pressure sensor, a micro-pressure testing system was established. The experimental results demonstrate that the sensor exhibits high sensitivity to micro-pressure, validating the effectiveness of the proposed design.

This paper presents the implementation of an AC three-phase programmable electronic load (PEL) that emulates load profiles and can be used for testing equipment in microgrids (MGs). The implemented PEL topology is built with a voltage source inverter (VSI) which works as a current controlled source and a Buck converter which permits the dissipation of active power excess. The PEL operation modes according to the interchange of active and reactive power and its operation in four quadrants were determined. The power and current limits which establish the control limitations were also obtained. Three control loops were implemented to independently regulate active and reactive power and ensure energy balance in the system. The main contribution of this paper is the presentation a detailed analysis regarding hardware limitations and the operation of the VSI and Buck converter working together. The PEL was implemented for a power of 1.8 kVA. Several experimental results were carried out with inductive, capacitive, and resistive scenarios to validate the proper operation of the PEL. Experimental tests showed the correct behavior of the AC three-phase currents, VSI input voltage, and Buck converter output voltage of the PEL for profile changes, including transient response.

New rapid, reliable, and cost-effective alternative systems are needed for the rapid diagnosis of Streptococcus pyogenes. The aim of this study was to fabricate a microfluidic test device to detect Streptococcus pyogenes by combining the Loop-mediated isothermal amplification method via a 3D printer. Microfluidic test devices were designed in CATIA V5 Release 16 software, and data were directly transferred to a 3D printer and produced using the FDM method with biocompatible PLA filament. The S. pyogenes ATCC 19615 and different ATCC strains was used. Following identification by classical culture methods, a 0.5 McFarland suspension was prepared from the colonies, and DNA isolation was performed from this liquid by a boiling method. S. pyogenes specific speB gene was used to desing LAMP primer sets in PrimerExplorer V5 software and tested on a microfluidic device. LAMP reactions were performed on microfluidic device and on a microcentrifuge tube separately. Both results were analyzed using the culture method as the standard method to diagnostic values. Melting curve analysis of the amplicons of the LAMP reactions performed on a LightCycler 480 system to detect amplification. Among the 50 positive and 100 negative samples, only four samples were found to be false negative by LAMP reaction in a microcentrifuge tube, while eight samples were found to be false negative by LAMP reaction on a microfluidic device. Six samples were found to be false positive by the LAMP reaction in the microcentrifuge tube, while ten samples were found to be false positive by the LAMP reaction on a microfluidic chip. The sensitivity, specificity, positive predictive value, and negative predictive value of the LAMP reactions performed in the microcentrifuge tube and on the microfluidic device were 92–84%, 94–90%, 88.46–80.77%, and 95.92–91.84%, respectively. The limit of detection (LOD) was found to be the same as 1.5 × 10[sup.2] CFU/mL and the limit of quantification (LOQ) values of the LAMP reactions were performed on the microcentrifuge tube and on the microfluidic device were 2.46 × 10[sup.2]–7.4 × 10[sup.2] CFU/mL, respectively. Cohen’s kappa (κ) values of the LAMP reactions were performed on the microcentrifuge tube and on the microfluidic device were 0.620–0.705, respectively. In conclusion, our data showed that the LAMP method can be combined with microfluidic test device to detect S. pyogenes, this microfluidic device can be manufactured using 3D printers and results are close to gold standard methods. These devices can be combined with LAMP reactions to detect different pathogens where resources are limited and rapid results are required.

Contact irritant (locomotor excitation) and noncontact spatial repellent avoidance behavior to deltamethrin and cypermethrin at dosages 0.025, 0.05, and 0.1 g/[m.sup.2] impregnated on papers were evaluated in the laboratory against deltamethrin- and cypermethrin-resistant field populations of female Aedes aegypti (L) from Rayong and Chanthaburi Provinces, Thailand. Pyrethroid-resistant populations were compared with a susceptible laboratory strain (NIH-Thai) using an 'excito-repellency' (ER) test system. Both NIH-Thai and field mosquitoes had stronger contact irritancy responses compared to the relatively weak noncontact repellency effects. Contact assays with deltamethrin and cypermethrin at 0.1 g/[m.sup.2] showed high escape rates for Rayong (80.1 and 83.4%, respectively) and Chanthaburi (84.6 and 73.1%, respectively) mosquitoes. Cypermethrin produced significantly different (P< 0.05) percent escape responses in contact tests between NIH-Thai and field mosquitoes. Only deltamethrin contact at 0.05 g/[m.sup.2] produced a significant escape response (P< 0.001) between NIH-Thai and Rayong mosquitoes. These results suggest that there may not be an overall significant effect of background pyrethroid resistance on escape response, and the differences by comparisons may reflect inherent individual variation when using the ER bioassay system. The results show that pyrethroid resistance in Ae. aegypti does not appear to influence or reduce contact avoidance responses with the compounds tested. In particular, deltamethrin at 0.1 g/[m.sup.2] was an effective contact irritant and toxic compound against pyrethroidresistant populations of Ae. aegypti. Therefore, 0.1 g/[m.sup.2] deltamethrin could be considered for residual applications of either fixed surfaces or materials (e.g., curtains) as a supplemental control measure against adult dengue vectors.

Simulations of impact events in the automotive industry are now common practice. Vehicle crashworthiness simulations on plastic components cover a wide range of strain rates from 0.01 to 500 s-1. Because plastics mechanical properties are very dependent on strain rate, developing experimental methods for generating stress-strain curves at this strain rate range is of great technological importance. In this paper, a modified Charpy machine capable of acquiring useful information to obtain the stress-strain curve is presented. Strain rates between 300 to 400 s-1 were achieved. Three thermoplastics were tested: high-density polyethylene, polypropylene-copolymer and polypropylene-homopolymer. Impact simulations using LS-DYNA were performed using the acquired high-strain rates stress-strain curves and compared with experimental data. Simulations using stress-strain curves from quasi-static tests were also performed for comparison. Very good agreement between the simulation and experimental results was found when the ASTM D1822 type S specimen was used for testing each material.

With the rapid increase of software complexity, automated testing has become the mainstream of software testing. However, the current automated test tools adopt a large number of common test equipment resource. At the beginning of the test, for specific test scenarios, the testers need to plan the test equipment resources according to the requirements of the software under test. An automatic test equipment resource planning and optimization algorithm based on group optimization is proposed IPSO (Improved Particle Swarm Optimization) to solve this problem. This method maps the requirement description to the equipment description to obtain the matching matrix, and then establishes a multi-objective constrained optimization model for test equipment resource planning. The solution is obtained through improved particle swarm optimization algorithm to achieve the optimal planning of test equipment resources. Compared with traditional manual planning methods, this algorithm reduces the workload of testers, and improves the automation and efficiency of testing. Experimental results demonstrate that the optimal solutions found by the algorithm proposed in this paper is superior to those of the PSO (Particle Swarm Optimization)) and Linearly Decreasing Inertia Weight Particle Swarm Optimization (LWPSO) algorithms.

We studied the effects of some nitrogen-containing, heterocyclic, and cyclic compounds on the rate of oxidative deamination of polyamines and putrescine in tissues with a high proliferation rate. For this purpose, the specific activities of the main enzymes of polyamine oxidative degradation-spermine oxidase (SMO), polyamine oxidase (PAO), and diamine oxidase (DAO) were determined using a cell-free test system from regenerating rat liver. The compounds methyl 2-(5-formylfuran-2-yl)benzoate and 2,7-bis-[2-(diethylamino)ethoxy]- 9H-fluoren-9-one (and in the form of dihydrochloride) showed mainly activating effect on oxidative degradation of putrescine, spermidine, and spermine, which indirectly indicates their antiproliferative effect. Nitrogen-free compounds inhibited this process, thus exhibiting potentially carcinogenic properties. Correlations were calculated for activity of DAO, PAO, and SMO with 5 topological indices: Wiener (W), Rouvray (R), Balaban (J) in the Trinaistich modification, detour (Ip), and electropy (Ie). The highest dependence was noted for DAO and the Balaban index (R=-0.55), for PAO and the detour index (R=0.78), and for SMO and the electropy index (R=0.53). The remaining dependencies showed insignificant correlation strength. Key Words: polyamines; diamine oxidase; polyamine oxidase; spermine oxidase; heterocyclic compounds