Explore the vast range of titles available.

Anthocyanins obtained from jambolan have been used as active agents in different carboxymethyl starch-based tablet formulations and their release profiles evaluated in simulated gastric fluids (SGF) and simulated intestinal (SIF) fluids. Structural analysis highlighted a strong interaction between anthocyanins and carboxymethyl starch, evidenced by scanning electron microscopy and infrared analysis. Tablet dissolution behavior varied according to the pH of the media, being controlled by the swelling and/or erosion of the polymeric matrix. Various formulations for immediate, fast, and sustained release of anthocyanins for 30 min, 2 h and 12 h of dissolution have been developed. It was found that monolithic carboxymethyl starch tablets loaded with powdered jambolan extract efficiently afforded the complete delivery (100% of anthocyanins) to different sites of the simulated gastrointestinal tract and ensured the stability of these pigments, which maintained their antioxidant activity.

This study investigated the various chemical modifications that affect the functional properties of Acorn starch. Acorn starch was modified using octenyl succinic anhydride, sodium trimetaphosphate (STMP), oxidation, and lactic acid at different concentrations, with their impacts assessed at various temperatures. Octenyl succinic anhydride–treated samples exhibited swelling power ranging from 2.9% at 60°C to 10.4% at 90°C. Modification levels significantly decreased swelling power (P < 0.05), due to structural changes in amylose and amylopectin and stabilization of starch granules from cross-linking. Pasting viscosities increased with modification levels; for example, peak viscosity rose from 1736.0 to 2033.0 cP with octenyl succinic anhydride modification from 3.0 to 9.0%. Lactic acid modification resulted in the highest peak viscosities, whereas STMP cross-linkage showed the lowest. The highest water-holding capacity (WHC) of 139.8% was found with octenyl succinic anhydride at 45°C, while STMP at 0.5% had the lowest WHC. Syneresis varied from 6.80 to 25.30% across freeze–thaw cycles, being lowest with oxidation and highest with STMP. Chemical modifications generally reduced dissolution rates, with lactic acid-modified starch showing the lowest dissolution (58.7%) after 24 h. Results indicated that chemical modifications significantly impact the properties of Acorn starch, emphasizing the need for careful selection based on application.

This paper presents structural evolution in iron oxide tablets at vibration testing for catalytic converters. The raw tablets composed from a mixture of cordierite powder with nanostructured iron oxide powders (pure and K-doped) and PVP binder. The analysis of the structural integrity of the raw tablets before vibration testing is evidenced by metallographic microscopic highlight the incidence of cracks. The raw tablets were mechanical vibration tested under normal operating conditions within the vibration damper to determine the structural integrity of the tablets. The mechanical vibration behavior of the tablets is essential in the development of new catalyst based on iron oxide nanoparticles for the reduction of gaseous pollutants from internal combustion engines.

A simple, sensitive and accurate HPLC method with high throughput has been developed and validated for the simultaneous determination of irbesartan (IRB) and hydrochlorothiazide (HCT) in combined pharmaceutical dosage forms. The proposed method employed, for the first time, a monolithic column in the analysis. Optimal chromatographic separation of the analytes was achieved on Chromolith® Performance RP-18e column using a mobile phase consisting of phosphate buffer (pH 4)/acetonitrile (50:50, V/V) pumped isocratically at a flow rate of 1.0 mL min . The eluted analytes were monitored with a UV detector set at 270 nm. Under the optimum chromatographic conditions, linear relationship with a good correlation coefficient (R ≥ 0.9997) was found between the peak area and the corresponding concentrations of both IRB and HCT in the ranges of 10-200 and 1-20 ng mL . The limits of detection were 2.34 and 0.03 ng mL for IRB and HCT, respectively. The intra- and inter-assay precisions were satisfactory as the RSD values did not exceed 3 %. The accuracy of the proposed method was > 97 %. The proposed method had high throughput as the analysis involved a simple procedure and a very short run- -time of < 3 min. The results demonstrated that the method is applicable in the quality control of combined pharmaceutical tablets containing IRB and HCT

This contribution describes use of a separation method based on on-line coupling of a multisyringe flow system with a chromatographic monolithic column for simultaneous determination of hydrochlorothiazide and losartan potassium in tablets. The system comprised a multisyringe module, three low-pressure solenoid valves, a monolithic C₁₈ column (25 mm x 4.6 mm i.d.), and a diode-array detector. The mobile phase was 10 mmol L⁻¹ potassium dihydrogen phosphate (pH 3.1)-acetonitrile-methanol (65:33:2 v/v/v) at a flow rate 0.8 mL min⁻¹. UV detection was carried out at 226 nm. The multi-syringe chromatographic (MSC) method with UV spectrophotometric detection was optimized and validated. Results from validation were very good. The analysis time was about 400 s. The method was found to be applicable to routine analysis of both compounds in tablets. The coupling of the monolithic columns with a multi-syringe flow-injection analysis manifold provides an excellent and inexpensive tool to solve the separation problems without use of HPLC instrumentation.

BackgroundLoratadine is a commonly used selective non-sedating antihistaminic drug. Desloratadine is the active metabolite of loratadine and, in addition, a potential impurity in loratadine bulk powder stated by the United States Pharmacopeia as a related substance of loratadine. Published methods for the determination of both analytes suffer from limited throughput due to the time-consuming steps and tedious extraction procedures needed for the analysis of biological samples. Therefore, there is a strong demand to develop a simple rapid and sensitive analytical method that can detect and quantitate both analytes in pharmaceutical preparations and biological fluids without prior sample extraction steps.ResultsA highly-sensitive and time-saving micellar liquid chromatographic method is developed for the simultaneous determination of loratadine and desloratadine. The proposed method is the first analytical method for the determination of this mixture using a monolithic column with a mobile phase composed of 0.15 M sodium dodecyl sulfate, 10% n-Butanol and 0.3% triethylamine in 0.02 M phosphoric acid, adjusted to pH 3.5 and pumped at a flow rate of 1.2 mL/min. The eluted analytes are monitored with fluorescence detection at 440 nm after excitation at 280 nm. The developed method is linear over the concentration range of 20.0–200.0 ng/mL for both analytes. The method detection limits are 15.0 and 13.0 ng/mL and the limits of quantification are 20.0 and 18.0 ng/mL for loratadine and desloratadine, respectively. Validation of the developed method reveals an accuracy of higher than 97% and intra- and inter-day precisions with relative standard deviations not exceeding 2%.ConclusionsThe method can be successfully applied to the determination of both analytes in various matrices including pharmaceutical preparations, human urine, plasma and breast milk samples with a run-time of less than 5 min and without prior extraction procedures. The method is ideally suited for use in quality control laboratories. Moreover, it could be a simple time-saving alternative to the official pharmacopeial method for testing desloratadine as a potential impurity in loratadine bulk powder.