Explore the vast range of titles available.

The optimal operation of high-voltage underground power cables is crucial for powering our communities, and it hinges on the intricate dynamics of insulation temperature around the conductor, primarily influenced by joule heating. This temperature responsiveness is further molded by seasonal and diurnal fluctuations in power demand, as well as the moisture content in the surrounding soil. Past research concentrated on theoretical analyses and experiments under dry conditions, but our study expands this scope. Through extensive laboratory tests exploring static and cyclic thermal loads in both dry and saturated sand environments, we uncovered valuable insights. Cyclic thermal loads in dry sand demonstrated a significant thermal charging effect, especially with shorter relaxation times. In static thermal loading, utilizing saturated sand enhanced heat dissipation due to higher thermal conductivity. However, it also revealed a noteworthy observation: a robust convection cell formed after three days of continuous heating, presenting challenges for cables under crop fields despite facilitating efficient cooling. Highlighting the importance of high-voltage power cable infrastructure, our study delves into the critical intersection between infrastructure and the underground soil. Understanding these interactions becomes imperative for the sustainable development of clean energy initiatives. As the world transitions to cleaner energy practices, optimizing the performance of underground power cable systems becomes pivotal in realizing their full potential and aligning with broader clean energy goals. This research contributes essential knowledge to enhance the safety, efficiency, and sustainability of high-voltage underground power cable systems in support of a cleaner and more sustainable energy future.

Background Subsea power cable failures in offshore wind farms result in significant financial losses. One common failure mode is submarine power cable bending. Objective The primary objective of this study is to validate two analytical models using strain readings obtained from a novel 3-point bending setup designed for power cable specimens. The setup incorporates two types of optical fiber sensors for simultaneous strain measurement. Methods A 3-point bending setup is constructed, integrating optical fiber sensors installed on the embedded fiber optic cable within the submarine power cable. One set of sensors is fixed to the fiber optic cable sheath, while a second set consists of loose tube fibers that are inside the fiber optic cable. The strain readings of the fixed sensors are compared to two analytical models. The first analytical model assumes a constant power cable curvature, while the second model considers variable curvature. Results The analytical models both predict nearly flat strain profiles and are in line with each other. The strain data, however, approaches zero strain away from the cable center. Model assumptions such as perfect sensor positioning and zero slip of the fiber optic cable cause this discrepancy. The results of the constant curvature model agree well with strain averages of the fixed sensors around the central region of the power cable, and both scale linearly with amplitude. Finally, the strain readings from the loose tube fibers demonstrate high reproducibility, facilitating the development of a calibration curve for estimating power cable curvature. Conclusions The analytical models surpass existing models by providing good agreement with the measured strain around the cable center. Moreover, the highly reproducible strain readings from the loose tube fibers allow estimating power cable curvature.

Empirical evidence suggests that marine animals perceive and orient to local distortions in the earth’s natural magnetic field. Magnetic fields (MFs) generated by electrified underwater cables may produce similar local distortions in the earth’s main field. Concern exists that these distortions may impact migration movements of MF-sensitive animals. The Trans Bay Cable (TBC) is a ± 200-kV, 400-megawatt, 85-km high-voltage direct current transmission line buried through San Francisco Bay (37° 56′ 8.81″ N, 122° 27′ 0.19″ W). Detections of adult green sturgeon implanted with acoustic transmitters were used from six cross-bay receiver arrays from 2006 to 2015 to investigate how inbound and outbound migration movements through lower portions of their route to/from upstream breeding grounds are related to the TBC’s energization status (off/on) and other local environmental variables. Here, we assess how these variables impacted transit success, misdirection from the migration route, transit times, and migration path locations within stretches between the Bay’s mouth and the start of the Sacramento River. Overall, there was varied evidence for any effect on migration behavior associated with cable status (off/on). A higher percentage of inbound fish successfully transited after the cable was energized, but this effect was nonsignificant in models including temperature. Outbound fish took longer to transit after cable energization. Inbound and outbound migration path locations were not significantly influenced by cable energization, but results suggest a potential subtle relationship between energization and both inbound and outbound paths. Overall, additional migration-based studies are needed to investigate the impact of anthropogenic cables on marine species.

Underground power cables are crucial for transmission and distribution. Lightning can stress their insulation, but not directly. So, impulse cable testing is studied. This research examines the cable’s transient response to standard and non-standard lightning impulse voltage waveforms. MATLAB Simulink was used to model a 132 kV wire with standard and non-standard impulse voltages. The IEC60060-1(2010) lightning impulse test uses a conventional waveform impulse voltage with a front time and a tail time of 1.2/50μs half value, while the non-standard test uses a front time and a tail time of 0.8/12s half value. Non-standard impulse waveforms are more accurate than standard waveforms. The impulse test voltage is four to five times the underground cable’s operational voltage and must withstand five applications without damage. Standard and non-standard impulse waveforms are injected with 132 kV and 550 kV to evaluate insulation failure or damage. Standard lightning and non-standard impulse voltage waveforms do not cause insulation failure or damage. When 132 kV and 550 kV are introduced into the normal and non-standard lightning impulse waveforms, the overshoot voltage increases. The peak voltage of a non-standard 550 kV impulse voltage waveform exceeds the IEC impulse withstand voltage. The finding shows that non-standard impulse voltage waves create increased cable voltage stress.

Power transmission covering long-distances has shifted from overhead high voltage cables to underground power cable systems due to numerous failures under severe weather conditions and electromagnetic pollution. The underground power cable systems are limited by the melting point of the insulator around the conductor, which depends on the surrounding soils’ heat transfer capacity or the thermal conductivity. In the past, numerical and theoretical studies have been conducted based on the mechanistic heat and mass transfer model. However, limited experimental evidence has been provided. Therefore, in this study, we performed a series of experiments for static and cyclic thermal loads with a cylindrical heater embedded in the sand. The results suggest thermal charging of the surrounding dry sand and natural convection within the wet sand. A comparison of heat transfer for dry, unsaturated and fully saturated sand is presented with graphs and colour maps which provide valuable information and insight of heat and mass transfer around an underground power cable. Furthermore, the measurements of thermal conductivity against density, moisture and temperature are presented showing positive nonlinear dependence.

This review represents a comprehensive study of nanocomposites for power cables insulations based on thermoplastic polymers such as polyethylene congeners like LDPE, HDPE and XLPE, which is complemented by original results. Particular focus lies on the structure-property relationships of nanocomposites and the materials’ design with the corresponding electrical properties. The critical factors, which contribute to the degradation or improvement of the electrical performance of such cable insulations, are discussed in detail; in particular, properties such as electrical conductivity, relative permittivity, dielectric losses, partial discharges, space charge, electrical and water tree resistance behavior and electric breakdown of such nanocomposites based on thermoplastic polymers are described and referred to the composites’ structures. This review is motivated by the fact that the development of polymer nanocomposites for power cables insulation is based on understanding more closely the aging mechanisms and the behavior of nanocomposites under operating stresses.

To overcome the shortcoming wherein the accuracy of subsea cable detection can be affected by the determination of the bias vector, scale factors, and non-orthogonality corrections of the vector magnetometer, a real-time attitude-independent route tracking method for subsea power cables is investigated theoretically and experimentally by means of scalar magnetic field checking. The measurement of the magnetic field Bc produced by the current in a cable is made immune to the influence of the platform attitude by extracting the component of Bc along the geomagnetic field using a high-bandwidth self-oscillating optically pumped magnetometer. The self-oscillating frequency is proved to be independent of the attitude of the magnetometer with the theoretical model. Experiments are carried out to test the attitude-independent performance, and the effectiveness of route tracking is verified by the results of the sea experiment. The proposed method will effectively improve the ability to locate subsea cables under high sea conditions.

One well‐known fault that arises from water intrusion and power cable insulation failure is the incipient fault (IF) in underground power cables (UPCs). Therefore, it is necessary to provide appropriate models for modeling this fault and also to generate data close to the actual value for validating IF detection methods. This study presents a model for IFs in UPCs, which provides the necessary data for the assessment. A few articles have been devoted to modeling the IF in UPCs, despite the numerous articles that have been introduced on arc modeling in other applications. This work deals with driving effective modeling of IFs in power cables from the two modified Avdonin models using the records of experiments obtained from a laboratory setup. The transient characteristics of IFs are demonstrated in the proposed models using the idea of transient coefficients. Also, the least squares method is used to update the models’ coefficients for every power frequency cycle. Finally, two error indices are introduced to establish each model’s optimal coefficients. Probability distribution functions (PDFs) were utilized to simulate the stochastic conduct of the model coefficients, which change with each cycle. As a result, for each combination of the model’s coefficients, some PDFs are examined, and the PDF that most closely matches the actual data is chosen. Also, the proposed models of this study are compared with the modified polynomial and modified Schwarz models.

The ageing characteristic of XLPE insulation of operating a 110 kV power cable with different service time is studied in this paper. The microscopic morphology of XLPE films from different cables were characterized by using Differential Scanning Calorimetry (DSC), X-ray Diffraction method (XRD), and Fourier Transform Infrared Spectroscopy (FTIR) methods, and the dielectric, mechanical, and electrical properties of XLPE were also measured. The relationship of several typical property parameters with the cable service time were established, and the ageing mechanism of XLPE insulation of the operating cable was also analyzed. It was found that XLPE insulation would endure a recrystallization process in the initial operation stage during which the microscopic morphology would become more perfect with higher crystallinity and denser crystal structure. Then, the thermal oxidation would dominate the ageing process of XLPE with the molecular chains broken and more micromolecular products generated after the cable had operated for more than 10–15 years. The AC breakdown strength decreases with the increase of cable service time, with lower decreasing rate in the initial operation stage and a larger rate after 10–15 years. The Pearson correlation coefficient between the cable service time with the characteristic parameters were calculated, and some of them were found to be effective to be used as indicators for operation state detection of operating power cables.

The surrounding (backfill) materials around the underground power cable systems are essential for dissipating the heat away from it, during the exertion phases. The heat dissipation restrains the thermal instability and risk of progressive drying of the backfill materials, thus reducing the thermal stress on the power cable. Thermal instability indicates the reduction in thermal properties (conductivity or diffusivity) due to the migration of moisture because of heat accumulation. Thus, the backfill materials should have adequate thermal properties and water retention capacity to transfer the heat from the heat source to the surrounding area with minimal moisture migration. The bentonite has high water retention capacity, but low thermal conductivity, whereas sand/fly ash exhibits low water retention and has higher thermal conductivity than bentonite. The addition of bentonite promotes the water holding capacity and thermophysical properties of sand and fly ash. Therefore, this study presents the thermal properties of backfill materials, bentonite–fly ash (B–F) and bentonite–sand (B–S), at varying weight-percent of sand and fly ash with bentonite. Various compositions of the mixtures were compacted to varying dry densities, and water contents and thermal properties variation of backfill materials were measured using a dual thermal needle probe ‘KD2 Pro’ at room temperature. The study deals with the systematic evaluation of the volumetric specific heat capacity, thermal conductivity, and diffusivity of backfill materials against varying dry density and water content. The threshold water content (TWC) has been determined from the thermal diffusivity–water content variation curve, and it has correlated with plastic limit (PL) and optimum moisture content (OMC). Thereafter, the efficacies of two thermal conductivity prediction models have also been evaluated statistically with respect to experimental results.